Question about 2005 Subaru Outback

1 Answer

I have a Subaru Van 700 and the Cam belt had broke . I found the timmig marks on the pulley of the can shaft and set it to tdc and fit new belt but no luck . After o long time trying to start this engine I have to remove the valve cover to set the valves overlapping then it started but lack of power. How can I know the true mark of the can shaft becouse the marks on the can shaft pulley is wrong. Thanks Vincent.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 438 Answers

Hello ,,my advice to you is to purchase a Chilton or equivalent service manual for your vehicle, all the necessary information to service most any problem can be found within the pages, these manuals can be obtained from almost any parts suppler at a reasonable cost good luck

Posted on May 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to set camshaft timing


you should have bought a Chilton or Haynes manual. most cars and trucks are all different and have a set way to set them. if you broke the chain or belt and bent a valve. you will need to do expensive repairs pulling the heads to change valves. not sure what car you have or why you pulled the timing off. so I cant be sure what to tell you.

Mar 12, 2015 | Cars & Trucks

2 Answers

The timing belt tensioner failed on my 2000 saturn Ls2 now the timing is off how do i get it back 2 tdc i got new belt n all pulleys but dont want 2 take belt off b4 i know how 2 get the timing back t


Remove Belt.Turn crankshaft pulley mark to line up with mark on housing TDC. Turn camshaft gear mark to line up with mark on head or block housing. More than one mark on cam gear ? If so turn camshaft till number four cylinder inlet and exhaust valves are just rocking this is the mark to use. ( same can be used on a six cylinder engine rocking number six valves ) fit new parts, tension belt, (TIP) now turn engine twice by hand , recheck that timing marks line up . saves a lot of time if you find they don't later.

Sep 16, 2014 | Cars & Trucks

1 Answer

What is timing belt installation sequence on a 1999 Mazda 626 6 cylinder?


set mark on crankshaft to TDC mark on timing cover. set mark on cam pulley to align with mark on head .if more than one mark on pulley rotate by hand till exhaust and inlet just rocking then align closest marks .

May 11, 2014 | Cars & Trucks

1 Answer

Engin runs ruff after a valve job


Make shore valve timing is correct compression test all cylinders same new spark plugs set ignition timing check ignition leads and vacuum hoses adjust tappets .make sure crank shaft on TDC cam shaft on number one cylinder valves close and cam pulley on marks belt tide fit distributor firing number one cylinder line up rotor and distributor cup lead to that .

Sep 21, 2012 | 1986 Chevrolet Camaro

1 Answer

I want to install new cam shafts on my Ford Puma after the timing belt snapped, How do I set the cams for TDC?


what damage was incurred when the belt broke if any. why are you changing the cams? if the damage has been rectified and you just want to change the cams find the timing marks on the relevant locations (ie) crankshaft and engine timing mark then the cams should only fit one way as there should be a locating dowl in the cams with timing marks on toothed cog

Jun 06, 2012 | 1997 Ford Puma

1 Answer

Need timing blet diagram 1992 ford ranger 2.3


Hi, the crankshaft marks are on the belt pulley and timing cover, so you have to mate it up to see them. The cam sprocket mark goes on the bottom, and aligns with another mark on the timing cover. There is a plug you pull out and hole to look thru to align the cam sprocket/shaft.


jturcotte_1801.gif


jturcotte_1802.gif


Rotate the engine so that No. 1 cylinder is at TDC on the compression stroke. Check that the timing marks are aligned on the camshaft and crankshaft pulleys. An access plug is provided in the cam belt cover so that the camshaft timing can be checked without removal of the cover or any other parts. Set the crankshaft to TDC by aligning the timing mark on the crank pulley with the TDC mark on the belt cover. Look through the access hole in the belt cover to make sure that the timing mark on the cam drive sprocket is lined up with the pointer on the inner belt cover.

Jun 01, 2011 | Ford Ranger Cars & Trucks

1 Answer

My balance shaft belt broke while I was driving. It stripped some of the teeth off the timing belt and Im pretty sure it jumped time. I need a diagram to show the timing marks and how to get it back in...


see diagrams from autozone.com. Cam sprocket has an "UP" label, but also 2 scribes on the sides to align to upper head surface. The critical part of the job is keeping tension on the side of the belt that is opposite from the tensioner as the tensioner is released onto the belt. The timing marks must be aligned when the job is done.

2bd7a51.jpg
4256a1c.gif To install:

  1. Install the camshaft timing sprocket so that the UP mark is up and the TDC marks are parallel to the cylinder head gasket surface. Install the key and tighten the bolt to 27 ft. lbs. (37 Nm).
  2. Install the crankshaft sprocket so that the TDC mark aligns with the pointer on the oil pump. Install the spacers with their concave surfaces facing in. Install the key. If equipped, install the TDC sensor assembly back into position before installing the timing belt.
  3. Install and tension the timing belt. Use a 6 x 1.0 mm x 25 mm bolt threaded through the cam belt tensioner plate to temporarily hold the tensioner.
  4. Temporarily install the crankshaft pulley and rotate the crankshaft counterclockwise 5-6 turns to be sure the belt is properly seated.
  5. Set the No. 1 piston at TDC for its compression stroke.



WARNING If any binding is felt when adjusting the timing belt tension by turning the crankshaft, STOP turning the engine, because the pistons may be hitting the valves.

  1. Rotate the crankshaft counterclockwise so that the camshaft pulley moves only 3 teeth beyond its TDC mark.
  2. Loosen, then retighten the temporary cam belt tensioner bolt.
  3. If the rear balance shaft sprocket/gear case assembly was removed, perform the following:
    1. If the rear balance shaft was moved, rotate the balance shaft until the 6 x 1.0mm x 100 mm bolt can be installed into the maintenance hole to the scribed line.
    2. Align the notch of the balance shaft sprocket edge with the pointer on the gear case. Install the rear balance shaft sprocket/gear case assembly using a new O-ring coated with fresh engine oil. The balance shaft sprocket should be installed in the TDC position. The pointer on the gear should align with the pointer on the oil pump housing plate.
    3. Tighten the mounting bolts to 18 ft. lbs. (25 Nm).

  4. If the front balance shaft sprocket was removed, perform the following:
    1. Install a suitable and sturdy screw driver or drift through the maintenance hole in the shaft behind the sprocket to hold the front balance shaft.
    2. Install the front balance shaft sprocket and mounting nut. Torque the nut to 22 ft. lbs. (29 Nm).

  5. Make sure the balance shafts and crankshaft are in the TDC position.
  6. Remove the crankshaft pulley, and if removed, install the balance shaft belt drive sprocket.
  7. Install the balance shaft belt, making sure the balance shafts and sprockets are still in the TDC position.
  8. If removed, install the balance shaft belt tensioner and tension the balance shaft belt.
  9. Loosen, then retighten the tensioner adjusting nut to 33 ft. lbs. (45 Nm).
  10. Remove the 6 x 1.0mm x 100mm rear balance shaft holding bolt.
  11. Temporarily install the crankshaft pulley and rotate the crankshaft 2 revolutions counterclockwise, stopping at TDC.



WARNING If any resistance is felt, stop immediately and determine the cause.

  1. Recheck that all of the TDC marks align for both the camshaft and balance shafts.
  2. Loosen, then retighten the tensioner adjusting nut to 33 ft. lbs. (45 Nm).
  3. Remove the 6 x 1.0 mm x 25 mm bolt used to secure the camshaft timing belt tensioner.
  4. Remove the crankshaft pulley and install the lower cover.
  5. Install the crankshaft pulley, lubricate the bolt threads and both sides of the crankshaft pulley bolt with fresh engine oil and tighten the crankshaft pulley bolt to 181 ft. lbs. (245 Nm). Do Not use an impact wrench.
See Figures 19 and 20


087aa27.gif

              Fig. Fig. 19: Holding the rear timing balancer shaft-4-cylinder Odyssey



            811a2fe.gif

            Fig. Fig. 20: Aligning the front timing balancer shaft-4-cylinder Odyssey

            1. Install the upper timing cover and the valve cover. Be sure the seals are properly seated.
            2. Install the side engine mount. Tighten the through-bolt to 47 ft. lbs. (64 Nm). Tighten the mount nut and bolt to 40 ft. lbs. (55 Nm) each.
            3. Remove the floor jack.
            4. Install and tension the alternator belt.
            5. Install the power steering pump and tension its belt.
            6. Install the splash shields.
            7. Reconnect the positive and negative battery cables. Enter the radio security code.
            8. Check engine operation.

            Sep 20, 2010 | Honda Odyssey Cars & Trucks

            1 Answer

            2002 hyundai accent DL sedan. my tension pulley


            hi from uk to retime cambelt is as follows = the crank cog has a mark which lines up with corresponding mark on front of engine block mark is approx 12-30 o/clock this is TDC No 1 the the cam cog has a small drilled hole in one of the webs just below the cog teeth ? this hole has to be at 12-o/clock position and then using a small mirror if you look through this hole you will see a vertical notch on the front of block this is theTDC mark for cam you then fit belt anticlockwise from c/shaft to cam then round tensioner then release tensionor to tension belt and then lock it up torque both bolts 20 - 27Nm rotate engine manually 4 complete turns clockwise then recheck marks ok /re align ? then re assemble crank pully bolt torque is 140 -150 Nm may i just inform you? that your engine is what is known as interferance that is to say in event of c/belt failure there is more than likely valves to piston contact however this can also occure too if miss timed belt fitted and engine has tried to start ? a compression test on cylinders will confirm if this has happened or not ? hope this helps

            Mar 16, 2010 | 2001 Hyundai Accent

            4 Answers

            1999 Plymouth Breeze 2.0 SOHC I just replaced the timing belt because the old one had not broke but rather had eaten off all the teeth so the timing was off. I set the timing mark on the crank to TDC...


            When changing the timing belt you need to place the cam shaft a TDC( clock wise), then rotate the crankshaft to TDC (clockwise), then back off the crankshaft (counter clockwise) THREE TEETH then back (clockwise) 1/2 tooth before TDC place your timing belt arround the crankshaft- water pump- and camshaft finally putting arround the tensioner pulley, holding 25 flbs of torque on the tensioner pulley to get the correct tension then push up on the hydrolic tensioner and tighten and you should have it.... rotate the crankshaft twice, if the camshaft pulley ends back on TDC then you have it correct.

            Nov 29, 2008 | Plymouth Breeze Cars & Trucks

            Not finding what you are looking for?
            2005 Subaru Outback Logo

            Related Topics:

            85 people viewed this question

            Ask a Question

            Usually answered in minutes!

            Top Subaru Experts

            yadayada
            yadayada

            Level 3 Expert

            76691 Answers

            Colin Stickland
            Colin Stickland

            Level 3 Expert

            22219 Answers

            Jeffrey Turcotte
            Jeffrey Turcotte

            Level 3 Expert

            8531 Answers

            Are you a Subaru Expert? Answer questions, earn points and help others

            Answer questions

            Manuals & User Guides

            Loading...