Question about 2002 Chrysler Concorde

Open Question

Replace the rear socks/struts on my 2002 Chrysler Concorde

How do I replace the rear socks/struts on my 2002 chrysler concorde?

Posted by on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 16 Answers

SOURCE: how to replace a radiator in a chrysler concorde 1998 3.2

Disconnect negative battery cable.
Drain cooling system.
Disconnect upper radiator hose.
Remove upper radiator closure panels.
Disconnect electrical connectors from electric fans.
Remove all mounting bolts for electric fans then remove from vehicle.
Raise vehicle. (You might not have to, but its easier)
Remove lower splash shield.
Disconnect lower radiator hose.
Remove lower condenser mounting bolts.
Lower vehicle.
Now back to the top.
Remove upper radiator mounting brackets and bolts.
Remove upper condenser bolts.
Now separate condenser from radiator.
Tilt radiator toward the engine and remove it from the vehicle.

Hope this helps





Posted on Dec 06, 2008

  • 99 Answers

SOURCE: How do I replace the battery in a 2004 Chrysler Concorde

Hi its pretty straight forward First remove the positive lead + then the negative - undo the battery cradle ( the bit holding the battery in place) reverse these instructions for reconnected job done
Hope this helps

Avoid = when undoing the positive lead + make sure the spanner doesnt contact any other metal component also make sure you reconnect the leads the correct way around + to + and - to -

Regards Steve

Posted on Dec 11, 2008

ZJLimited
  • 17970 Answers

SOURCE: how do you replace the egr valve in a 1997

Chrysler Concorde 1993-1997 3.5L MFI 6cyl
Exhaust Gas Recirculation System
Operation

This system reduces the amount of oxides of nitrogen (NO x ) in the exhaust by allowing a predetermined amount of exhaust gases to recirculate and dilute the incoming fuel/air mixture. The diluted air/fuel mixture reduces peak flame temperature during combustion, which in turn inhibits the production of Nitrogen oxides. The principal components of the system are:
- EGR tube (connects a passage in the intake manifold to the exhaust manifold)
- EGR valve
- Electronic EGR Transducer
- Vacuum hoses


Component and System Testing

  1. Check the condition of all of the EGR system hoses and tubes for leaks, hardening or kinks on the rubber hoses. Repair and correct these conditions before proceeding any testing.
  2. Be sure that the hoses at both of the EGR valve and EGR valve control are connected to the proper fittings.
  3. Be sure the electrical connector is firmly attached at the valve control.
  4. To check the EGR system operation, connect the DRB III scan tool or equivalent to the 16-way data link connector. The data link connector is located on the lower edge of the instrument panel near the steering column. Follow the scan tool instructions.
  5. After checking the system with the DRB III scan tool, proceed to the EGR valve leak and control tests, then repair as necessary.

Removal & Installation
EGR Valve and Transducer

395f8b9.jpg

EGR valve and transducer assembly-3.5 engine



025dc6c.jpg

The EGR valve attaches to the back of the cylinder head-3.5L engine


bc80254.jpg

Loosen, but do not remove, the EGR tube to intake manifold screws

The EGR valve attaches to the rear of the right cylinder head.
  1. Remove the vacuum tube from the electric EGR transducer solenoid. Inspect the vacuum lines for cracking, poor seal due to hardness, or other problems. Replace with new hoses if necessary.
  2. Remove the electrical connector from the solenoid.
  3. Slide the transducer up and out of the mounting bracket.
  4. Loosen, but do not remove, the EGR tube to the intake manifold screws.
  5. Remove the EGR tube lower screws at the valve.
  6. Remove the EGR valve and transducer.
  7. Clean both gasket surfaces and check for any signs of leakage or cracks. Replace the components if any such damage is found or if the valve fails the tests.

To install:
  1. Loosely install the EGR valve and a new gasket onto the cylinder head.
  2. Using a new gasket, attach the EGR tube to the valve and tighten the screws to 95 inch lbs. (11 Nm).
  3. Tighten the EGR tube to the intake manifold plenum screws to 16 ft. lbs. (22 Nm).
  4. Tighten the EGR valve to the cylinder head screws to 16 ft. lbs. (22 Nm).
  5. Reconnect the transducer solenoid to the vacuum fitting on the manifold.
  6. Slide the transducer into the bracket.
  7. Reconnect the vacuum lines and electrical wires to the EGR transducer.
continue...

Posted on Sep 04, 2009

  • 1 Answer

SOURCE: 1999 Chrysler Concorde LXI Rear Speaker replacement

If you mean the rear shelf removal, then you begin by removing the rear seat (lift to release the corner clips on each side holding the cushion to the floor). Then remove the fasteners for the seat belts, then lift the seat back to raise and release it from its clips, and remove it from the vehicle. There are then a lower and upper trim panel around the back shelf that you need to remove (these may be on each side of the shelf, e.g. they are called 'quarter trim' panels). Then you will see some push-pin fasteners that hold the shelf across the front lower edge, so you gently pry out the center push-pin of each one of those to release the fastener. Then you pull the shelf forward to release it from the clips that hold it under the window. Then remove the wire to the center high-mounted brake light. The panel with its speakers attached can then be removed, but also remove the wires from the speakers so you don't break those. connections.
That is the procedure as shown in my '98 manual.

Posted on Apr 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change rear struts


Remove the bolts at the top & bottom !!
Top nuts may be in the trunk

Aug 11, 2013 | 2002 Chrysler Concorde

1 Answer

My 2002 chrysler concorde door handle has lost all tension and will not open the door from the inside. any advice??


My concorde 2003, both right side locks wont open from inside. The front one has broken handle and the rear one is without any tension.

Oct 05, 2010 | 2000 Chrysler Concorde

1 Answer

My 97 Chrysler Concorde runs good but shocks/ struts need replaced to make smoother ride - i was hoping someone would have cost estimate or tell me how to repair. I am new to this town and don't know any...


If you have struts on the front, only certified auto mechanics can fix, go to reliable name such as walmart, midus, brake stop etc. they will treat you right, check online for prices of struts, shocks, check ebay for prices, labor is about the same price as parts, I would say between 5-800 for all four.

Feb 15, 2010 | 1997 Chrysler Concorde

1 Answer

Rear strut install


I have a 1999 Chrysler LHS and have had the rear struts done for me. You have to remove the back seats to get at them. I know its not the total solution, but it should put things in a better perspective for you.

Jun 02, 2009 | 2000 Chrysler Concorde

1 Answer

Approximate price to replace chrysler concorde rear door 98


Prices will vary depending on a few factors. You can most likely get a used door at a local salvage yard for $100 and up. There's one on ebay right now for $299.

May 08, 2009 | 1998 Chrysler Concorde

Not finding what you are looking for?
2002 Chrysler Concorde Logo

Related Topics:

425 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...