Question about 2000 Honda Accord

1 Answer

Got the wires mixed up on the distributor cap on my honda accord 2.3 L

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,374 Answers

1,3,4,2 is the firing order. Look at distributor and picture an imaginary line in the center of it from top to bottom 1 is top left, 3 is top right, 4 is bottom right and 2 is bottom left. There are ony four possible combinations if you mix up the top and bottoms .Write down on a piece of paper how you set them up in the event you get it wrong you can try it a different way. I don't know whybut currently I can't get a picture of this to you .

Posted on May 06, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

That helps but where is the number 1 cylinder on the distributor cap 1994 honda accord ex


From ZJ limited: "1.6L Engines Firing order: 1-3-4-2 Distributor rotation: Clockwise.

cdd80c6.gif
"

Apr 12, 2015 | 1994 Honda Accord

1 Answer

Do i disconnect spark plug wires from valve cover or leave those in and disconnect from distributor instead... 97 honda accord


Depends on what you are trying to do.
If you are removing the valve cover leave the wires attached to the distributor cap.

Sep 29, 2012 | 1997 Honda Accord

1 Answer

I have a 98 honda accord 5 spd it has a 4cyl motor vtech i just need to know how to fix a miss fire in cylinder 2 and wich one is cylinder 2


Cylinder #2 is the the second spark plug counting from the right to left.
EX.Below are spark plug on engine
engine
-------------------------------
' (oil cap) '
' (4) (3) (2) (1) '
'_________________'

Your misfire can be cause by couple of things but the cheapest way that you can try to fix your car is to do a tune up by replacing:
1)all spark plugs
2)do a oil change
3)spark plug wires
3)distributor cap and rotor

note misfire can be cause by:
1.bad gas
2.spark plug and/or wire
3.distributor cap and/or rotor
4.valve adjustment
5.injector
6.off timing
7.ECM
8.bad wiring(power, ground or feed line)

Jul 08, 2011 | 1998 Honda Accord

1 Answer

How to do a tuneup


Hi, disconnect the 3 harness attached and the distributor cap and/or spark plug wires. Remove 3- 12mm bolts. Pull disconnect the 3 harness attached and the distributor cap and/or spark plug wires. Remove 3- 12mm bolts. Pull on the distributor. When re-installing reiverse the process. Make sure that the distributor shaft is line up with the on the distributor. When re-installing reiverse the process. Make sure that the distributor shaft is line up with the notches on the cam. It only fits on way. If in one position dont fit. turn the shat 180 degree.
Take care

Aug 02, 2010 | 1992 Honda Accord

1 Answer

The sequence is 1342, ****............


The rotor of the distributor rotates clockwise as you look down into it, there should be a mark on the cap - or a raised area to locate the 2 / 1 meeting position.

start clockwise of the mark and the first point is plug 1, then 3 and so on till 4. after 4 you should feel / see the mark again.

Apr 30, 2010 | 1997 Honda Accord

1 Answer

91 honda accord ran out of gas now no spark


Check the ignitor, Honda uses a couple of different distributors, my 92 has the ignitor inside the distributor cap, w/ 4 wires attached (push on type). Pull off the wires (note where they all go) and remove one screw to remove ignitor (it's been a while since I changed it, there might be 2 screws, but it would be easy to see). If it's bad, you will have no spark. If this doesn't help, let me know, I'll try to help further.

Apr 11, 2010 | 1991 Honda Accord

1 Answer

How to remove and install a distributor on a 1993 honda accord?


1. remove the distributor cap and rotor, don't remove the spark wires. 2. unplug the wire from the distributor. 3. remove the distributor bolts, pull the distributor out. When install the distributor make sure replace the new O ring.

Apr 09, 2010 | 1993 Honda Accord

2 Answers

I need the firing order for a 1989 honda accord 4 cyl fi plugs to rotor


1 3 4 2 number one should be marked on the correct tower.

Sep 18, 2009 | 1989 Honda Accord 4 Door

2 Answers

I need the firing order for a 1987 Honda Civic 1500cc (carburated model). This car has a distributor, but the plug wires connect in a straight line rather than in circular fashion around the distributor...


I found an illustration for an 87 Civic 1.5L engine, carbureted. By the looks of it, it's 1-3-4-2 although this graphic shows a round cap. I see the Accord 2.0L does have the plugs in a line, not in a circle. Hope this helps!
a569f71.gif

Dec 15, 2008 | Honda Civic Cars & Trucks

Not finding what you are looking for?
2000 Honda Accord Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...