Question about 2006 Ford Fusion

2 Answers

Ford fusion 2007, blown blower fuse, replaced fuse, works at highest speed only (highest of 4) the other three setings don't work.

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,309 Answers

Hte blower resistor is shot, near the blower motor, have the blower motor checked my guess is that it requiring too much power to run, hence the blown fuse

Posted on May 06, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 510 Answers

You need to replace heater motor speed resistor,located behind center of dash

Posted on May 06, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 ford fusion heater fan not working.it was working sometimes but now it wont work at all.


Probably the blower motor is bad , worn brushes , armature commutator . They get worn spot on the commutator . You mite try hitting on the bottom of the blower motor housing to see if that makes it work . If it starts working the motor is bad .

Dec 21, 2016 | 2007 Ford Fusion

1 Answer

Ford windstar. Speed control problem on rear blower. It only works on high speed (4).


possible bad switch... possible loose wires to the switch and or motor...

Feb 11, 2014 | 2000 Ford Windstar

1 Answer

Sentra AC


There's a 10amp fuse that powers the ac clutch relay and compressor. There are 15amp fuses that power the blower motor and the ac control switch. All of those fuses get power from the key switch. The resistor and fan switch provide the ground circuit for the blower motor.
I would want to know if those fuses are getting power, and if the control panel is working. You should be able to ground the blower motor and make it run on high, and that should not have any effect on if the ac compressor is running or not.
It could be a key switch problem in that the circuit is not strong enough to handle the load from the blower and the compressor at the same time.

Jun 21, 2013 | Cars & Trucks

1 Answer

Air does not blow


The car normally blows air through the blower however the controls and settings of the speed of the blower are controlled by the blower motor resistor. The resistor controls the speed of the blower fan. If your blower still works on the highest setting then the blower itself is still in working order. If you are not getting any air at all, even on the highest setting, then chances are the blower has gone bad, blown fuse or open wire. If this does not help please give us more information to work with.

Aug 12, 2012 | 2002 Buick Century

1 Answer

My ford fusion 2006 the a/c blower motor will stop working on firs speed after half of an hour and i replace the resistor and steel duing the same


I have a 2008 fusion and the main control for the ac and blower will not turn anything on is there a main fuse or relay for that cause i checked the fuses and they were all good

May 02, 2012 | 2003 Ford Taurus

1 Answer

My blower only works 1 through 4 and will not work on the highest position number 5


{: ) Check out the J-case fuse (square) labeled BLWR 40amps at the underhood fuseblock. This fuse is the source of power to the blower motor when position 5(max speed) is selected. If this fuse is tested to be okay, you need to access for the blower resistor connectors. Turn ignition on, and set blower to max speed (#5). Probe on the blower resistor terminal (orange wire) and you should get 12volts, also probe the terminal (red wire) which came from the 40amp fuse. 12v should be present on these two terminals at the blower resistor when at max blower speed. Particularly on the orange wire, if you don't get 12volts when at #5 position, it 's probable that the blower speed control switch is faulty. But if you did got 12volts during the procedure, then you should replace the blower motor resistor. Goodluck.

Jul 24, 2011 | 2006 GMC Envoy

1 Answer

Fan motor will only work when the switch is in the highest speed position


Having the year, make, model, and engine size would help.

But generally when this occurs it is a bad motor resistor. The resistor uses a set of resistors in series to drop voltage to control blower speed. The lowest setting uses all the resistors and the setting below high speed uses on resistor. Since none of the lower speeds work either the resistor for the setting just below high is burned out or the internal fuse has blown. Replacing the blower motor resistor should take care of the problem.

Oct 20, 2010 | Ford F-250 Cars & Trucks

1 Answer

I have two first my four speed fan only runs on speed 4 FAST and the second is my front washer does not work


If your blower motor will only run on the highest speed the blower motor resistor pack is defective and needs replacing. If the windshield washer does not work then the fuse is blown or the motor is defective. If the motor is running but no spray is coming from the nozzles then the nozzles are clogged with wax. Use a needle to unclog them.

Apr 18, 2010 | 2000 Ford Focus

2 Answers

Blower motor does not work


Check for a blown fuse, or a faulty blower motor control relay.

Jun 26, 2009 | 1999 Mercury Sable

Not finding what you are looking for?

Open Questions:

See all 2006 Ford Fusion Questions

2006 Ford Fusion Logo

1,367 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...