Question about 1994 Oldsmobile Cutlass Ciera

2 Answers

Where are the starter bolts located? 1994 Olds Ciera S w/v6

Where are the bolts for removing the starter on a 1994 Olds Cutlass Ciera with a V6 engine (OHV)?

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,317 Answers

Should be between the radiator and engine, underneath the car. There might be a plastic cover held on with 10mm bolts. The starter bolts go up thru the starter, into the block.

Posted on May 07, 2010

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Actually, I had to remove the filter, filter guard, flywheel inspection covers, electric fan, and one sensor connector. Then, it was a breeze!

Posted on May 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1994 Olds Cutlass Ciera starter issues


You should have two or three wires that go to the large post on the solenoid, including the 4 gauge wire from the battery. Then one 16 gauge wire to the small post. That wire comes from the key switch.
Let me know if you need colors for wires.

Mar 01, 2013 | 1994 Oldsmobile Cutlass Ciera

1 Answer

Verify firing order for a 1994 v6 olds cutlass ciera


1 2 3 4 5 6 if its a 3.1L with an "M" in the vin code. Olds had the 3.1, the 3.4, and the 3.8L V6 engines that year

Sep 20, 2011 | 1994 Oldsmobile Cutlass Ciera

2 Answers

Do you know where the 2 bolts are on a starter for a 94 olds cutlass ciera s?


REMOVE THE STARTER FLY WHEEL COVER. STARTER BOLTS IS VERTICAL BOLTED INTO THE ENGINE.

Jul 08, 2011 | 1994 Oldsmobile Cutlass Ciera

1 Answer

Needs to be replaced where is it located 1994 Oldsmobile Cutlass Ciera 3 0 v6 thermastat


Follow the top radiator hose. Where it connects to the engine, there is a thermostat cover. Remove the two bolts and the thermostat is under the cover.

Mar 14, 2011 | Buick Century Cars & Trucks

1 Answer

Where are the starter bolts located 3.1 olds. ciera


There are only two bolts holding the starter in place and a small bracket.

Dec 11, 2010 | 1994 Oldsmobile Cutlass Ciera

1 Answer

Where exactly is a crank sensor on a 1988 olds. 2.8 v6


should be behind the bottom pulley(harmonic balancer)(crankshaft pulley).You will have to remove the bolt in the pulley first,to do this.You will have to remove the starter or there might be a small shield where the tranny and engine attach.This will give you a way to hold the engine so you can remove the bolt.I use an old main bearing and put in the teeth on flywheel.once bolt out You will have to get a 2 or 3 jaw puller and pull the pulley off.

Feb 19, 2010 | 1992 Oldsmobile Cutlass Ciera

1 Answer

'95 cutlass ciera, Mating the trans and engine?


Hi
Fit the torque convertor to the gearbox first, make sure it locates fully with the pump drive on the g/box(the round section that's got two flat sections) in the centre of the bellhousing. Make sure the convertor does not slip out when mating engine and g/box, when mated there should not be any gap between engine and g/box(transmision) without any bolts tightened, secure transmision to engine then only replace the bolts that holds the torque convertor to the flexplate.

Regards
Phillip

Oct 16, 2009 | 1994 Oldsmobile Cutlass Ciera

1 Answer

Replace oxygen sensor a 94 Olds Cutass Ciera S 3.1 V6 Engine where is it located. Roy M F


it should be in the exhaust manifold, if not just below the manifold in the exhaust header pipe,

ACDELCO Part # AFS75
SENSOR,HTD OXY(POSN 1) IN EXH MANIFOLD/CROSSOVER

Sep 04, 2009 | 1989 Oldsmobile Cutlass Ciera

1 Answer

Symptoms of a failing (plugged) fuel filter - GM V6 Olds Cierra


Rought idel, stalls alot, poor excelaration, starts hard, playing with gas peddel to keep running, they are also symptoms of fuel pump getting weak, or going out, should have fuel pressure test.

Feb 14, 2009 | 1994 Oldsmobile Cutlass Ciera

2 Answers

Thermostat


take off the top hose then remove the houseing it should have 2 -4 bolts after you remove them pull out the thermostat this is on a v6 or v8 let me know what you have if you would

Aug 15, 2008 | 1995 Oldsmobile Cutlass Ciera

Not finding what you are looking for?
1994 Oldsmobile Cutlass Ciera Logo

883 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...