Question about Chevrolet Silverado 1500

1 Answer

1995 Silerado; right rear turn signal doesn't work. Initially the right front didn't either. I replaced the front lamps and all 3 of the right rear lamps. This fixed the front but not the back. I replaced the 20 amp fuse and still it doesn't work. It blinks very rapidly but only the right front is functional. The emergency flasher doesnot flash on right rear side either. The other three sides work fine. What do you think?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Chevrolet Master
  • 3,854 Answers

Bad ground wire to the rear socket or the socket is bad and needs to be replace. Inspect the condition of the sock and replace if corroded, inspect the ground wire to make sure it has not corroded off.
Thank you for using fixya and good luck. Keep me posted on your progress and if your having a hard time, i'll send you the illustration to your wire harness location.

Posted on May 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

08 Buick lucerne cxl. Third brake light works as well as front signal lights. No rear brake lights or turn signals. Tail lights and headlights and third brake lights works. Bulbs good. Help


Stop Lamps
The brake pedal position sensor is used to sense the action of the driver application of the brake pedal. The body control module (BCM) provides a 5-volt reference voltage and low reference to the brake pedal position sensor. The position sensor provides an analog voltage signal back to the BCM that will increase as the brake pedal is applied. When the brake is applied, the BCM will then apply battery voltage to the left and right stop/turn signal lamp supply voltage circuits and the center high mounted stop lamp (CHMSL) supply voltage circuit illuminating the stop lamps. At the same time the BCM applies battery voltage through the signal circuit to the transmission control module (TCM) and the engine control module (ECM) indicating that the brakes are applied.
Ground for the stop lamps is supplied as follows:
• G402 provides ground for the left rear stop/tail/turn signal lamps
• G403 provides ground for the right rear stop/tail/turn signal lamps
• G301 provides ground for the CHMSL
The stop lamps on this vehicle will not illuminate unless the ignition is in the accessory, run, or crank positions. When the ignition is in the OFF position the stop lamps will not illuminate when the brake pedal is applied.
Battery voltage from the LT TRN/SIG and RT TRN/SIG fuses located in the rear fuse block is also used by the body control module (BCM) for stop lamp operation.

Turn Signal Lamps
Battery voltage supplied to the body control module (BCM) from the fuses listed below is used for turn signal and hazard lamp operation.
• LT TRN/SIG fuse for the left turn signals
• CTSY/RF TRN fuse for the right front turn signal
• RR TRN/SIG fuse for the right rear turn signal
When the turn signal switch is place in either the LEFT or RIGHT position, ground from G300 is applied through the turn signal switch signal circuit to the BCM indicating the turn signal request. In response to this signal, the BCM applies a pulsating voltage to the front and rear turn signal lamps supply voltage circuits cycling the lamps ON and OFF. At the same time the BCM sends a GMLAN serial data message to the instrument panel cluster (IPC) to cycle the appropriate turn signal indicator ON and OFF.
Ground for the turn signal lamps is supplied as follows:
• G104 provides ground for the left and right front turn signal lamps
• G402 provides ground for the left rear stop/tail/turn signal lamps
• G403 provides ground for the right rear stop/tail/turn signal lamps

Do you have a factory scan tool (tech2) ? Your best bet , take it to the dealer .

Sep 08, 2017 | Buick Cars & Trucks

1 Answer

Why is my 2008 chevrolet uplander's turn signal does not making clicking sound , but the signal lights are working.


Did you put a aftermarket radio in ? The clicking sound comes out the driver side speaker . It's generated by the BCM body control module .
Turn Signal Lamps
The STOP/TURN fuse in the instrument panel (I/P) fuse block supplies battery positive voltage to the body control module (BCM) for the turn signal lamps. When the turn switch is placed in the left or right position, ground is applied to the BCM on the left or right turn signal switch signal circuit. The BCM then applies voltage to the appropriate front and rear supply voltage circuits.
Grounds for the various lamps are as follows:
• G100 supplies the right front lamps
• G101 supplies the left front lamps
• G400 supplies the right rear lamps
• G401 supplies the left rear lamps

Your best bet would be to take it to a qualified repair shop before you start replacing parts , like the BCM ,which would need to be programmed at the dealer or other thing's will stop working too .

Aug 30, 2017 | Chevrolet Cars & Trucks

1 Answer

My right front turn signal doesn't work, I have replaced the bulb the right rear works fine


You would check the socket with a test light or meter to see if you have power and ground. If no power, the turn signal switch would be the next thing to check.

Jan 25, 2013 | 1999 Toyota Corolla

1 Answer

On my 2004 impala, the front right turn signal doesn't work, (only works with hazard lights). And the back right signal is fast. The signal "clicking" sound is non stop but on the other hand...


If the turn signal filament of the right front park/turn lamp is known to be OK and the hazard switch is in the normal position, the hazard switch or the turn signal/multi-function switch could be defective

Oct 16, 2012 | Cars & Trucks

1 Answer

2003 Jeep liberty right front turn signal


why skip RR lamp? what does IT DO? be like 1st 1st look.
dim, out, fast?

the rapid is talking to you
it means current is wrong,
shorted, or open lines. to the right.
its the wiring
if the bulbs are like 1157 brass base bulbs
why not replace them first , they can short inside,
asking online for guessing is silly, why listen to 10 examples for this.
but is cut wires.
shorted wires.
keep i mind the blinker asks funny for both opens and shorts
its a feature, that.
low current or too much.

the acid test is connect 2 TEST bulbs in parallel to the multi-function switch output right side,
blinks ok now, bingo bad lamps or bad wiring, from there to the right side.

if the hazard fails you never said????
if rigth front is dim or dead the bulb is blown or shorted
if new bulb there , then the wires are shorted.
to it.
the only help on line worth squat is how to test and use your meter.
you can, check for voltage
you can check continuity on that line (its just 1 wire)
and check for shorts on that wire to ground (lamps pulled right side to do that, lamps read 0 ohms cold)
look for collision damage RF? behind lamp sockets?
be first.
in my book.
looking is always first. sure.


I have your SM book open now, chapter 8w-50
the haz/blink module has just 2 pins, left and right out.
pin 3 on the module runs front and rear blinks, (a fact to know)
RF is BR/RD, brown -red stripe?
all comments USA on USA forum. USA car.
ok?

the right side lamp (sidemaker) only blinks turns if parks ARE oFF

Id try 2 new blinker lamps front and 1 rear.
that be first. or test the lamp on a battery , and no not get burned fingers hot wring a shorted lamp.

wish i knew
what rear did
and what both did on HAZ
out, dim or to fast.

Mar 23, 2017 | 2003 Jeep Liberty

1 Answer

03 chevy venture rt.front parking light&turn light don't work replace bulb&socket


The rapid flashing occurs because of the light problem. If the 20A PARK LP fuse in the underhood fuse block is OK, the front marker lamps and the park lights should turn on when you set the headlamp switch to PARK. If the 10A T/SIG fuse in the instrument panel fuse block is OK, and the ignition switch is on, moving the turn signal multi-function switch to signal a right or left turn should cause the turn signals to flash. If this doesn't happen, check for a missing ground connection to the socket you replaced and check to be sure the replacement lamp was not forced into the socket backwards (it happens).

Sep 17, 2012 | 2003 Chevrolet Venture Passanger

1 Answer

My 2001 ford expedition right hand rear turn signal and brake light doesn't work but right front signal works


Multi-function switch,(Wipers turn signals cruise) , this may sound crazy, but if you can get to the screws & remove it, smack the unit on a table top 2-3 times & re-try.
Let me know what happens. This DOES work on all Ford U-Haul trucks!

Jul 12, 2012 | Ford Expedition Cars & Trucks

1 Answer

Right rear tran signal lamp does not work. changed light bulb still does not work. Front turn signal lamp blinks real fast


Please check the cables lead to your rear turn lamp for loose connection. Both turning lamps ( rear and front) should work to keep turning lights back to normal blink.
Regards

Feb 19, 2011 | 1997 Isuzu Hombre

3 Answers

I tried replacing the right rear turn signal twice. Still only get a fast on-off flash on the dash and only the right front signal works. Left turn signals are fine.


The circuit boards in Chevrolet tail lamps ar notorious for going bad. Dorman makes a replacement circuit board, part number 70006 . the same part number will fit either the left or right side of your Trailblazer.

Nov 24, 2010 | 2006 Chevrolet Trailblazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...