Question about 2003 Mitsubishi Galant

1 Answer

Timing belt replacement intervall - 2003 Mitsubishi Galant

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 104 Answers

60k miles!!

Posted on May 06, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

At what interval should the rear brakes be replaced for a 2003 murano

there is no intervall, just replace them when worn

Oct 26, 2010 | 2003 Nissan Murano

1 Answer

I have to change the campbell or don`t need it ? thanks

Your BMW has a timing chain there is no service intervales for this only when you start to hear a chain rattle.
Regards Indy

Aug 17, 2010 | 1996 BMW 318

3 Answers

1995 toyota camry leaking oil from behind the timing belt cover. Isn't this a major repair? Is the leak more than likely a camshaft seal?

If you haven't had the timing belt replace (60,000 miles is the suggested service intervale) this is an overlap of having the timing belt replaced.
If the timing belt is not due for replacement and its the cam shaft seal that is leaking. Its a pretty easy fix. Remove the top timing belt cover , and the crankshaft sensor wiring you may have to remove the front engine mount . Set #1 piston at TDC, Loosen tensioner w/ spring slip off belt. **Remove sprocket pull out old seal with a sharp pick. Greese and install new seal make sure its flush with its bore . Reistall sprocket. Slide belt over Cam sprocket tighten tensioner. Install cover and mount (if applicable) Check timing marks by turning crank two revolutions.
** If CamSprocket Bolt is difficult to remove then remove valve cover and use a 21mm wrench to hold the Camshaft while you crack off Cam Sprocket Bolt.
You will see the groves on the Camshaft where you can place a wrench to hold the shaft.
After you replaced the seal replace the valve cover gasket ONLY IF YOU HAD TO REMOVE THE COVER TO HOLD THE CAM WHILE REMOVING ITS BOLT.

This is about as major as it gets.

May 12, 2010 | 1995 Toyota Camry

1 Answer

When should cambelt be changed on a c70 convertible

105,000 miles is the scheduled factory replacement intervall.i would change it at that time if it breaks then you have some big dollar engine damage

Mar 20, 2010 | 2001 Volvo C70

1 Answer

Timebelt change

it varies from manufacturer to manufacturer but typically it is recommended to be replaced between 60K - 100K miles. A visual inspection of the belt for cracks, missing teeth, or parting will also help you determine if the belt needs to be replaced.

Feb 26, 2010 | 2006 Peugeot 604

1 Answer

Hi, When does the timing belt on the 2004 Magentis v6 have to be changed?

Average recommended change intervall on a timing belt is 60,000 miles, I change mine at 40 to 50,000 miles.
Good luck!

Nov 24, 2009 | 2004 Kia Optima

1 Answer

Where are the spark plugs in a 2004 trailblazer

They are Located UNDER the INDIVIDUAL CIOL PACKS , on the TOP of ENGING. ECCESSED By Removing the 10mm Bolt that Holds Coil in Place, once bolt is removed Pull COIL OFF and Spark Plug is UNDER it. There Is ALSO a BOOT on EACH one that Requires Replacment at Basicly the SAME Intervalls as SPARK PLUGS.

Oct 22, 2009 | 2004 Chevrolet TrailBlazer

1 Answer

My check engine light blinks 12 times

not sure about the 12 times one but i know the blinking then staying on and missing then shut it off and changing the sensor and it running ok when you start it.... thats because your catalitic converter is cloged, usually from miss fires or bad/old plugs/wires you need to replace your cat cause its beyond repair and make sure to change your plugs and wires (and i would do my fuel filter and air filter while i was at it if it were me) or else you will have the same problem right around the corner. I know this due to the fact it happened to both my parents cars and when i bought my truck with 103000 miles the guy before me NEVER changed his stuff, (supposed to do plugs and wires at 12000 mile intervales) and it was all factory, Hope this helps.

Jul 25, 2008 | Jeep Cherokee Cars & Trucks

Not finding what you are looking for?
2003 Mitsubishi Galant Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts


Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8575 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides