Question about 2008 Mercury Mariner

1 Answer

Do you have to remove the head to get to the other 3 spark plugs?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,857 Answers

No, you may be able access them from underneath or your going to have to remove the intake if your not limber enough to reach behind. It can be a hassle some times.

Posted on May 06, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Spark plugs


Check this SPARK PLUG REPLACEMENT - REMOVAL PROCEDURE

1_23_2012_5_10_32_pm.jpg

1. Remove the ignition coils (lines at end this document), then return here once you have gotten the Coil
Packs off and precede with step 2 from here.
2. Clean the spark plug recesses with low pressure air. CAUTION: Wear safety glasses
when using compressed air, as flying dirt particles may cause eye injury. NOTE:
Clean the spark plug recess area before removing the spark plug. Failure to do so could
result in engine damage because of dirt or foreign material entering the cylinder head, or
by the contamination of the cylinder head threads. The contaminated threads may prevent
the proper seating of the new plug. Use a thread chaser to clean the threads of any
contamination.
3. Remove the spark plugs from the cylinder head. NOTE: Allow the engine to cool before
removing the spark plugs. Attempting to remove the spark plugs from a hot engine may
cause the plug threads to seize, causing damage to cylinder head threads.
4. Inspect the spark plugs.

INSTALLATION PROCEDURE

1_23_2012_5_11_30_pm.jpg

1. Measure the spark plug gap on the spark plugs to be installed. Compare the measurement
to the gap specifications. NOTE:
• Use only the spark plugs specified for use in the vehicle. Do not install spark
plugs that are either hotter or colder than those specified for the vehicle. Installing
spark plugs of another type can severely damage the engine.
• Check the gap of all new and reconditioned spark plugs before installation. The
pre-set gaps may have changed during handling. Use a round feeler gage to ensure
an accurate check. Installing the spark plugs with the wrong gap can cause poor
engine performance and may even damage the engine.
2. Install the spark plugs to the cylinder head. NOTE:
• Be sure that the spark plug threads smoothly into the cylinder head and the spark
plug is fully seated. Use a thread chaser, if necessary, to clean threads in the
cylinder head. Cross-threading or failing to fully seat the spark plug can cause
overheating of the plug, exhaust blow-by, or thread damage.
• Refer to Component Fastener Tightening Notice in Service Precautions.
Tighten the spark plugs to 18 N.m (13 lb ft).
3. Install the ignition coils.

IGNITION COIL(S) REPLACEMENT
REMOVAL PROCEDURE
1. Remove the air cleaner resonator and outlet duct.
2. Disconnect the engine wiring harness electrical connector (1) from the oil pressure sensor (2).
3. Disconnect the engine wiring harness retainers (1) from the power steering pump (2).
4. Disconnect the engine wiring harness electrical connectors (1, 4) from the following:
• The exhaust camshaft position (CMP) sensor (5)
• The camshaft position (CMP) actuator solenoid valve (6)
5. Disconnect the engine wiring harness retainer (2) from the camshaft cover (3).
6. Disconnect the engine wiring harness electrical connectors from the following:
• The engine coolant temperature (ECT) sensor (1)
• The fuel injector harness (2)
• The ignition coils (4)
• The heated oxygen sensor (HO2S) (5)
7. Disconnect the engine wiring harness electrical connector from the intake camshaft position (CMP) sensor.
8. Carefully disengage the engine wiring harness conduit from the camshaft cover, and position aside.
9. Remove the ignition coil bolts.
10. Remove the ignition coils from the camshaft cover.

INSTALLATION PROCEDURE
1. Install the ignition coils into the camshaft cover. IMPORTANT: Ensure the ignition coil seals are properly seated to the camshaft cover.
2. Install the ignition coil bolts. NOTE: Refer to Fastener Notice in Service Precautions. Tighten the ignition coil bolts to 10 N.m (89 lb in).
3. Attach the engine wiring harness conduit to the camshaft cover.
4. Connect the engine wiring harness electrical connector to the intake CMP sensor.
5. Connect the engine wiring harness electrical connectors to the following:
• The ECT sensor (1)
• The fuel injector harness (2)
• The ignition coils (4)
• The HO2S (5)
6. Connect the engine wiring harness electrical connectors (1, 4) to the following:
• The exhaust CMP sensor (5)
• The CMP actuator solenoid valve (6)
7. Connect the engine wiring harness retainer (2) to the camshaft cover (3).
8. Connect the engine wiring harness retainers (1) to the power steering pump (2).
9. Connect the engine wiring harness electrical connector (1) to the oil pressure sensor (2).
10. Install the air cleaner resonator and outlet duct.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jan 23, 2012 | Cars & Trucks

Tip

How To Change The Spark Plugs On A 2002-2005 Kia Sedona 3.5 Liter


You'll need to remove the oil cap and the 6 bolts holding on the engine cover. The front 3 spark plugs are pretty easy to replace. You'll need to unplug the spark plug wire from the coil and disconnect the electrical connector. Unbolt the 2 10mm bolts holding the coil to the valve cover. Twist the coil and boot back and forth and pull it out of the cylinder head. The spark plug is down in the head, you'll need at least a 6 inch extension with a 5/8" spark plug socket, a telescopic magnet will help get the spark plug out of the head. The back 3 spark plugs involve removing the upper intake and throttle body, unbolt the bracket to the throttle body, and the bracket bolted to the upper intake manifold. on the back side of the engine. Remove the tubing from the throttle body to the air cleaner box. Unbolt anything else bolted to the upper intake. Unplug electrical connectors to the throttle body and any other electrical connectors on the upper intake and remove the upper intake bolts. And move the upper intake out of the way, there are only spark plug wires on the back 3 plugs. Twist and turn each boot to aid in removing the boot from the plug. I would get a new upper intake gasket and consider replacing the wires at this time also. There are actually only 3 spark plug wires, so for what is involved to get to them, I would replace them. I have found alot of the wires will arc to the upper intake manifold.

on May 02, 2010 | Kia Sedona Cars & Trucks

1 Answer

How to change spark plugs in a 2005 chev colorado


SPARK PLUG REPLACEMENT - REMOVAL PROCEDURE

1_23_2012_5_10_32_pm.jpg

1. Remove the ignition coils (lines at end this document), then return here once you have gotten the Coil
Packs off and precede with step 2 from here.
2. Clean the spark plug recesses with low pressure air. CAUTION: Wear safety glasses
when using compressed air, as flying dirt particles may cause eye injury. NOTE:
Clean the spark plug recess area before removing the spark plug. Failure to do so could
result in engine damage because of dirt or foreign material entering the cylinder head, or
by the contamination of the cylinder head threads. The contaminated threads may prevent
the proper seating of the new plug. Use a thread chaser to clean the threads of any
contamination.
3. Remove the spark plugs from the cylinder head. NOTE: Allow the engine to cool before
removing the spark plugs. Attempting to remove the spark plugs from a hot engine may
cause the plug threads to seize, causing damage to cylinder head threads.
4. Inspect the spark plugs.

INSTALLATION PROCEDURE

1_23_2012_5_11_30_pm.jpg

1. Measure the spark plug gap on the spark plugs to be installed. Compare the measurement
to the gap specifications. NOTE:
• Use only the spark plugs specified for use in the vehicle. Do not install spark
plugs that are either hotter or colder than those specified for the vehicle. Installing
spark plugs of another type can severely damage the engine.
• Check the gap of all new and reconditioned spark plugs before installation. The
pre-set gaps may have changed during handling. Use a round feeler gage to ensure
an accurate check. Installing the spark plugs with the wrong gap can cause poor
engine performance and may even damage the engine.
2. Install the spark plugs to the cylinder head. NOTE:
• Be sure that the spark plug threads smoothly into the cylinder head and the spark
plug is fully seated. Use a thread chaser, if necessary, to clean threads in the
cylinder head. Cross-threading or failing to fully seat the spark plug can cause
overheating of the plug, exhaust blow-by, or thread damage.
• Refer to Component Fastener Tightening Notice in Service Precautions.
Tighten the spark plugs to 18 N.m (13 lb ft).
3. Install the ignition coils.

IGNITION COIL(S) REPLACEMENT
REMOVAL PROCEDURE
1. Remove the air cleaner resonator and outlet duct.
2. Disconnect the engine wiring harness electrical connector (1) from the oil pressure sensor (2).
3. Disconnect the engine wiring harness retainers (1) from the power steering pump (2).
4. Disconnect the engine wiring harness electrical connectors (1, 4) from the following:
• The exhaust camshaft position (CMP) sensor (5)
• The camshaft position (CMP) actuator solenoid valve (6)
5. Disconnect the engine wiring harness retainer (2) from the camshaft cover (3).
6. Disconnect the engine wiring harness electrical connectors from the following:
• The engine coolant temperature (ECT) sensor (1)
• The fuel injector harness (2)
• The ignition coils (4)
• The heated oxygen sensor (HO2S) (5)
7. Disconnect the engine wiring harness electrical connector from the intake camshaft position (CMP) sensor.
8. Carefully disengage the engine wiring harness conduit from the camshaft cover, and position aside.
9. Remove the ignition coil bolts.
10. Remove the ignition coils from the camshaft cover.

INSTALLATION PROCEDURE
1. Install the ignition coils into the camshaft cover. IMPORTANT: Ensure the ignition coil seals are properly seated to the camshaft cover.
2. Install the ignition coil bolts. NOTE: Refer to Fastener Notice in Service Precautions. Tighten the ignition coil bolts to 10 N.m (89 lb in).
3. Attach the engine wiring harness conduit to the camshaft cover.
4. Connect the engine wiring harness electrical connector to the intake CMP sensor.
5. Connect the engine wiring harness electrical connectors to the following:
• The ECT sensor (1)
• The fuel injector harness (2)
• The ignition coils (4)
• The HO2S (5)
6. Connect the engine wiring harness electrical connectors (1, 4) to the following:
• The exhaust CMP sensor (5)
• The CMP actuator solenoid valve (6)
7. Connect the engine wiring harness retainer (2) to the camshaft cover (3).
8. Connect the engine wiring harness retainers (1) to the power steering pump (2).
9. Connect the engine wiring harness electrical connector (1) to the oil pressure sensor (2).
10. Install the air cleaner resonator and outlet duct.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jan 23, 2012 | Cars & Trucks

1 Answer

Where are soark plugs


Vehicles: 2000 Kia Sportage 4-cylinder 2.0L MFI DOHC 1998-2002

They're hidden underneath the coil cover, which is partially obscured by the accelerator cable bracket, which is obstructed by the air intake.

They're accessed from the top of the engine.

If you don't have a compressed air line to blow dirt away from around the plugs before removing them, one may blow through a plastic drinking straw (while closing eyes), or use a can of compressed air (with a little red plastic straw) sold for use cleaning computer PC boards/keyboards.

Where the manual (below) says "carefully install the spark plug into the cylinder head", you may consider one or another of a couple of experienced mechanic's tricks (used to avoid cross-threading the plug thus damaging the head):
trick 1: start plug by putting plug onto the end of a piece of stiff-ish hose, and
start the threads by gently turning the end of the hose. Once plug has
safely started turning into its threads, switch to a spark plug socket.
trick 2: use the spark plug socket, but carefully start the plug by gently
turning the plug COUNTER-clockwise, until the plug drops a hair - at this
point you know you've found the start of the first thread. Then gently thread
the plug in clockwise.
--------------------------------------------------------------
Spark Plugs - Removal & Installation

WARNING
Do not attempt to remove spark plugs when the engine is hot.

(1) Disconnect the negative battery cable.
(2) Remove the air intake hose assembly.
(3) Remove the accelerator cable bracket.
(4) Remove the six bolts and coil cover from cylinder head cover.
(5) Remove the four bolts and the two coils from the cover.
(6) Disconnect the high tension leads from the spark plugs by twisting the boot and removing.
(7) Use compressed air to remove any dirt from around the spark plug hole.
(8) Make sure the spark plug socket fits squarely on the spark plug, and then remove.
--------------------------------------------
To install:

(1) Be sure the spark plug gap is set to 0.039-0.043 in. (0.98-1.09mm).
(2) Apply anti-seize compound or light lubricating oil (WD-40 or 3-in-1) to the spark plug threads.
(3) Carefully install the spark plug into the cylinder head and torque to 11-17 ft. lbs. (23 Nm).
(4) Reconnect high tension leads to the spark plugs.
(5) Install the two ignition coils and torque four mounting bolts to 14-19 ft. lbs. (26 Nm).
(6) Install the coil cover and secure with six bolts
(7) Install the accelerator cable bracket.
(8) Reconnect the air intake hose assembly
(9) Reconnect the negative battery cable.

Dec 02, 2011 | 2000 Kia Sportage

1 Answer

How do i change spark plugs on a 2000 kia sportage


YOU REMOVE THE CYLINDER HEAD COVER.YOU REMOVE SPARK PLUGS FROM TOP OF THE ENGINE CYLINDER HEAD.FIRST YOU REMOVE THE IGNITION COILS AND HIGH TENSION LEADS THEN REMOVE SPARK PLUGS.YOU NEED SPARK PLUGS SOCKET THE LONGER SOCKET WILL BE GOOD YOU NEED LONGER EXTENSION, YOU NEED SPARK PLUGS GAP GAUGE AND A 3/8 RATCHET WRENCH. YOU NEED A TORQUE WRENCH ITS NOT MANDATORT BUT JUST DONT OVER TIGHTEN SPARK PLUGS OR YOU WILL DAMAGE THE ALUMINUM HEAD THREADS.

Sep 05, 2010 | 2000 Kia Sportage

1 Answer

How to change plugs on honda odyssey 2005


you will need
8mm
10mm
5/8 spark plug socket
3/8 ratchet
3/8 extension (it could be 4in and longer)
and spark plugs factory plugs are pregap iridium
spark plug torque is 13.0 lb.ft
coil torque 8.7 lbf.ft
spark plug part # NGK 1zfr5k-11
# DENSO pkj16dr-m11
and spark plug anti seize on spark plug thread
what you need to do is remove the plastic cover 8mm socket or 10mm sockets
now remove the spark plug covers and remove the spark plug coils too 10mm head bolt you will need a 5/8 spark plug socket and a 3/8 ratchet and a 3/8's extension too
you need OEM spark plugs they work the best
hope this will help

May 22, 2010 | 2005 Honda Odyssey

1 Answer

Where are the spark plugs?


you have 3 in the front engine head, you will see 3 spark plug wires accross the front cylinder head. The remaining three are located in the rear cylinder head. You must remove the intake manifold to access this.

May 10, 2010 | 1993 Toyota Camry V6

2 Answers

Do i nee a certain tool to get to the spark plugs in a 2001 chevy metro


There are no "special" tools required. Here is how you would do it:

NOTE: This engine is equipped with an aluminum cylinder head. Allow the engine to cool before removing spark plugs. Removing the spark plugs from an engine at operating temperature may damage the spark plug threads in the cylinder head. Also be sure to clean any dirt or debris from around spark plug holes prior to removing spark plugs.

I also recommend putting a small amount of anti-seize compound on the threads of the spark plugs when installing. Be careful not to under or over-tighten because cylinder head damage could result. If you have access to a torque wrench, the specification is 11 foot pounds.

  1. Disconnect the ignition coil electrical connectors.
  2. Carefully release the number 1 spark plug wire from the clip on the number 2-3 ignition coil.
  3. Remove the 2 bolts from each ignition coil.
  4. Remove the number 1 spark plug wire and the number 1-4 ignition coil from the spark plugs.
  5. Remove the number 2-3 ignition coil and the number 3 spark plug wire from the spark plugs.
  6. Remove the spark plugs from the cylinder head.
  7. Reverse proceedure to install.

Nov 08, 2009 | 2001 Chevrolet Metro

1 Answer

Where are the spark plugs on my 2000 Oldsmobile Intrigue and how do i change them?


2000 Oldsmobile Intrigue V6-214 3.5L VIN H SFI

Spark Plug: Service and Repair
REMOVAL PROCEDURE
TOOLS REQUIRED
J 43094 Spark Plug Boot Puller
1. Turn OFF the ignition switch.
2. Remove the ignition coil assembly.
3. Use the J 43094 in order to remove the spark plug boots from the spark plugs.
NOTE: Allow the engine to cool before removing the spark plugs. Attempting to remove the spark plugs from a hot engine may cause the plug
threads to seize causing damage to cylinder head threads.
NOTE: Clean the spark plug recess area before removing the spark plug. Failure to do so could result in engine damage because of dirt or
foreign material entering the cylinder head, or by the contamination of the cylinder head threads. The contaminated threads may prevent the
proper seating of the new plug. Use a thread chaser to clean the threads of any contamination.
4. Remove the spark plugs from the engine.
INSTALLATION PROCEDURE
NOTE: Use only the spark plugs specified for use in the vehicle. Do not install spark plugs that are either hotter or colder than those specified for the
vehicle. Installing spark plugs of another type can severely damage the engine.
NOTE: Check the gap of all new and reconditioned spark plugs before installation. The pre-set gaps may have changed during handling. Use a round
feeler gage to ensure an accurate check. Installing the spark plugs with the wrong gap can cause poor engine performance and may even damage the
engine.
1. Measure the spark plug gap on the spark plugs to be installed. Compare the measurement to the gap specifications. Refer to Spark Plug Usage.
Correct as necessary.
NOTE: Be sure that the spark plug threads smoothly into the cylinder head and the spark plug is fully seated. Use a thread chaser, if necessary,
to clean threads in the cylinder head. Cross-threading or failing to fully seat the spark plug can cause overheating of the plug, exhaust blow-by, or
thread damage.
NOTE: Refer to Fastener Notice in Service Precautions.
2. Install the spark plugs to the engine.
Tighten
Tighten the spark plug to 20 N.m (15 lb ft).
3. Install the spark plug boots to the ignition coil assembly.

5c212b8.jpg
4. Install the ignition coil assembly.

Sep 13, 2009 | 2000 Oldsmobile Intrigue

1 Answer

Change spark plug wires on 04 kia sedona


REMOVAL OF THE PLUGS:

Do not attempt any maintenance on spark plug if engine is hot. 
1. Disconnect negative battery terminal. 
2. Carefully remove high-tension leads. 
3. Use compressed air to blow any dirt or debris from around spark plug hole. 
4. Check that spark plug fits squarely in spark plug socket and remove spark plug.

Raise a vehicle and install SST(OK552 131 001) in order to replace cylinder 2, 4, 6 spark plug. 

INSTALLATION:

1. Install spark plug into cylinder head.

Tightening torque : 18~22lb-ft (25~30N·m, 2.5~3.0kg-m)

2. Reconnect high-tension leads. 
3. Reconnect negative battery cable. 

Hope this helps and simple to understand. Good luck

Apr 20, 2009 | 2004 Kia Sedona

Not finding what you are looking for?
2008 Mercury Mariner Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

fordexpert

Level 3 Expert

5501 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...