Question about 1985 Nissan Pickup

1 Answer

1985 Pickup: clutch catches too close to the floor....

Clutch catches too close to the floor.

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 630 Answers

Needs to be raised on the lift and adjusted for proper adjustment.
usually if it is too high it is ready for replacement

Posted on May 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1994 toyota pickup


No, this is a hydraulic clutch and the only adjustment may b on the pedal linkage for free travel to the master cylinder. It sounds as though you may have a bad clutch master cylinder or defective slave cylinder.

Apr 26, 2014 | 1994 Toyota Pickup

1 Answer

Toyota pickup clutch


Hi Tonio,could be your slave cylinder is bad,not holding pressure and leaking,if so then your clutch reservoir is low.Here's a link to it. Repair Guides Clutch Slave Cylinder AutoZone com

Mar 18, 2014 | 1993 Toyota Pickup

2 Answers

1985 pickup truck is having problems I put it in gear it will drive juss very slow and over revs what do I do. I have money just need advice. As well other gears are hard to catch


If you have manual clutch the it appears that the clutch is not operating as it should. Check if there is clearance between the throw out arm and the slave cylinder rod and if not replace the clutch master cylinder as it is holding pressure in the line and not allowing the clutch to fully engage. If it is a cable operation then replace the cable

Nov 04, 2013 | Cars & Trucks

1 Answer

My clutch pedal used to be pretty stout and the clutch would engage at about the midway point to the floor. All of a sudden the clutch pedal is pretty free to the floor where the clutch now engages. what...


sounds to me like the clutch master cylinder might be bad usually this happens when the line or the clutch master cylinder leaks fluid and you lose pressure to your clutch pedal...you should have a hydraulic clutch on this truck...if its leaking it will need to be replaced its located under the truck usually on the drivers side mounted on the transmission bell housing...hopes this helps

Mar 21, 2011 | 1985 Toyota Pickup

1 Answer

My clutch is very free till almost the floor where it now engages. it used to engage about midway to the floor. what could have caused this?


you should buy a self adjusting clutch, you can set the clutch yourself, to catch right away,or, a couple of inches of play, It could also be your clutchplate, not cheap! I hope this helps you in some way

Mar 21, 2011 | 1985 Toyota Pickup

1 Answer

Cluth has to be on floor to shift


your truck has a hydraulic clutch, which has a master cylinder next to the brake master cylinder. Check the fluid level. If it is low or empty, you have a leak in the master or slave cylinder (at the transmission).
Replace the leaking part and bleed the system to restore clutch pedal.

Sep 07, 2010 | 1985 Nissan Pickup

1 Answer

Clutch petal goes to the floor with little resistance. can't get in gear.


fill the reservoir for the clutch slave cylinder. No with the engine OFF pump the clutch 25 times. Yes 25 times. Now start the engine and see if it shifts. If it does you need a new slave cylinder, clutch, pressure plate, & throwout bearing as well. Everything is replaced upon dismantling for you do now want to do it again within a few months later. Also have the flywheel machined smooth if its still any good

Aug 30, 2010 | 1985 Nissan Pickup

1 Answer

Hydraulic clutch grinding from 1st to 2nd - Toyota 1985 Pickup


Yes, your clutch might be worn and/or out of adjustment or the trans is worn. Your clutch may be fine also. Toyota's have a problem with there shifter bushings and seats. They brake and crack also causing shifting problems. And some times only one gear depending on the condition.If yours is broken,crack or damaged, you can find the parts from Toyota and there a whole lot cheaper than a clutch. Also I recommend adjusting the clutch if possible. Not all are adjustable. Check your clutch fluid.


a87388d.jpg

Mar 24, 2009 | 1985 Toyota Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

114 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...