Question about 2005 Chevrolet Equinox

1 Answer

Rigth front door will not go up or down all other windows do

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Contributor
  • 181 Answers

Will is go up from either switch left or right side switch? If not it will probably need a window motor

Posted on May 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2005 Gmc Sierra 5.3 litter SLT. Wire diagram for passanger side power window. No power to door.


Do the power door locks work for that door ? Does you vehicle have door courtesy lights , turn signals on the mirror ? If your vehicle has these other options an they work , you have power to the door . There is an electronic module inside the door ,called passenger door module ! where did you check for power at , the window switch ! These are computer controlled an you would only see a few volts when pushing the switch !

7

  1. Monitor the passenger front window status in the passenger door module inputs list.
  2. Activate the passenger power switch on the passenger door module in the up and down positions.
Does the window status data parameter change accordingly?
Go to Step 8
Go to Step 15

8

  1. Monitor the passenger front window status in the driver door module inputs list.
  2. Activate the passenger front power window switch on the driver door module in the up and down positions.
Does the window status data parameter change accordingly?
Go to Step 9
Go to Step 16
Operate the passenger front power window in the UP and DOWN directions from the master switch.
Does the passenger front power window operate properly from the master switch?
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
Go to Step 5

4

  1. Install a scan tool.
  2. Monitor the window lockout data parameter in the driver door module inputs list.
  3. Activate the window lockout switch to both the On and OFF positions.
Does the window lockout data parameter change state appropriately?
Go to Step 5
Go to Step 16
Your best bet is to take this to dealer or a ASE certified repair shop.

Jun 14, 2015 | GMC Cars & Trucks

1 Answer

I want to change my steering wheel from the left side to rigth of car to drive from the rigth


If they made a right hand drive model you would need to get the front clip, steering, harnesses, dash and interior for it. Then have a body shop remove the front of your van and install the front from the right hand drive. Literally everything from the steering wheel forward would have to be removed in order to make it work. You would be looking a tens of thousands of dollars to make this happen.

Feb 20, 2015 | 2004 Chrysler Town & Country

1 Answer

Why the rear driver side window does not go up or down


Fuse blown switch stuffed, control module in door fritzed, window motor brushes worn out.
please get back tous with your solution so we cam
n help others in the future.
PS other Nissan motors can be slipped in from other Nissan models to fix a motor problem....and much cheaper..and if you go to a wrecker, make sure you get the correct motor for the correct side, yes Martha, the motors are Rigth side only, and Le side only, same front and rear. Refer to the serial numbers, get one that ends in the same number.......

Jul 06, 2014 | Nissan Pathfinder Cars & Trucks

3 Answers

1997 mercury grand Marquis driverside rear window motor works but window won't go up. Inner door panel off. Metal cable with a black foam cover and pink plastic clip off. Can't figure what it fits to.


usually this means you need a new window regulator.

Section 01-11: Glass, Frames and Mechanisms 1997 Crown Victoria, Grand Marquis Workshop Manual
REMOVAL AND INSTALLATION Window Regulator, Power Front Door
Removal
  1. If front door window glass (21410) is in the down position and is inoperable, the following steps must be taken; if front door window glass is operational, go to Step 2.
    1. Remove front door trim panel (23942) and front door trim shield (237A04). Refer to Section 01-05 .
    2. Disconnect battery ground cable (14301). Refer to Section 14-01 .
    3. Disconnect window regulator electric drive harness connector.
    4. sva~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Be careful not to strike or scratch front door window glass because it can break.
      Remove window regulator electric drive retaining screws through holes.
    5. Remove window regulator electric drive (23394) from front door power window regulator.
    6. Raise front door window glass to full up position by hand and secure with tape.
    7. Go to Step 5.

  2. Remove front door trim panel and front door trim shield. Refer to Section 01-05 .
  3. Remove front door window glass as described.
  4. Disconnect window regulator electric drive harness connector.
  5. NOTE: Use care not to enlarge sheet metal holes in the door inner panel.

    Remove two 1/4-inch rivets retaining lower bracket of front door power window regulator to inner panel. Use drift punch to knock out center pins for each rivet. Using a 1/4-inch diameter drill, drill out remainder of rivet.
  6. Remove three window regulator electric drive retaining screws from inside door to remove window regulator electric drive from front door power window regulator.
  7. Remove two window regulator retaining nuts.
  8. Remove front door power window regulator from front door (20124).
Installation
  1. Lubricate regulator mechanism with Teflon® Lubricant E7FZ-19590-A or equivalent meeting Ford specification ESB-M1C111-A.
  1. Install front door power window regulator minus motor (23208) into access hole in inner panel.
  1. Position front door power window regulator using upper studs and tabs on window regulator electric drive mounting bracket.
  1. Install rivets retaining front door power window regulator to door inner panel (1/4-20 x 1/2 inch screw and 1/4-20 nut and washer assemblies or equivalent metric fasteners may be used).
  1. Install two upper front door power window regulator retaining nuts.
  1. Install window regulator electric drive with three screws. Do not overtighten screws.
  1. Connect the window regulator electric drive harness connector.
  1. Install front door window glass.
  1. Adjust front door window glass as described.
  1. Install front door trim shield and front door trim panel. Refer to Section 01-05 snorkelbobby_38.gif

Feb 14, 2011 | 1997 Mercury Grand Marquis

1 Answer

Where is the brake bleeder on a 1995 oldsmobile cutlass supreme?!?!


you have 4 of them 2 in front / 2 in back . 2 in back are on the brake backing plate 1 bleeder on each side. 2 in front 1 bleeder on each side on the caliper. when bleeding start with rigth rear left rear front rigth frontleft . check master cylinder fluid level while bleeding. keep full of fluid

Nov 12, 2010 | 1995 Oldsmobile Cutlass Supreme

1 Answer

I want to remove passenger side rear door panel because window is down and won't stay up


Hi,
Hi!!

Here is a little information on how window regulator works. Also step by step instruccions on how to remove and install the window glass.

Door Glass & Regulator Power Windows
Diagnosis & Testing
When the rear window lockout feature is enabled, the circuit is open and no voltage is supplied to the rear window switches. When the feature is not enabled, the circuit is connected to battery positive voltage. If this circuit is shorted to ground when the lockout feature is not enabled, the PWR WDO circuit breaker may cycle continuously OFF/ON until, either the lockout switch is pressed to open the circuit, or the circuit breaker is permanently damaged. All windows may be partially or totally inoperative while the fault is present.
Inspect for aftermarket devices which could affect the operation of the system. Inspect the easily accessible or visible system components for obvious damage or conditions which could cause the symptom. Faulty electrical connections or wiring may be the cause of intermittent conditions.
Removal & Installation
Window Motor & Regulator
  1. Position window approximately half way down in the door.
  2. Remove the interior trim panel.
  3. Remove the water deflector.
  4. Tape the window to door frame to prevent it from moving.
  5. Remove the three front door window regulator motor screws.
  6. Disconnect the electrical connector from the window regulator motor.
  7. Remove front side door window regulator motor.
  8. To install, reverse removal procedure.

Window Switch
Front
  1. Remove the front door pull cup screws and pull cup from the front door trim panel.
  2. Disconnect the electrical connectors from the front door power window control switch.
  3. Remove the front door window control switch using a small, flat-bladed tool at the side of the switch.
  4. To install, reverse removal procedure.

Rear
  1. Remove the rear door pull cup from the rear door trim panel.
  2. Disconnect the electrical connectors from the power window control switch.
  3. Remove the rear door window control switch from the pull cup using a small, flat-bladed tool at the side of the power window control switch to release the power window control switch retainer.
  4. Remove the power window control switch from the rear door pull cup.
  5. To install, reverse removal procedure.

Sep 07, 2010 | 2002 Buick Century

1 Answer

Just replaced passenger front window on the 2001 v70. Do not remember if window stops an inch down or does it go all the way down?


I am not exactly sure on this model but most of the time the power windows on the front doors go down all the way. I would check the right passenger side door if it goes all the way down, then most likely the drivers side door should also. Usually the rear windows go down and stop an inch from being all the way down. Some cars are set up to lower the front windows only an inch then by pressing the window down button again, they will continue to roll all the way down.

Jan 02, 2010 | 2001 Volvo V70

1 Answer

Left front door window sometimes will not go back up! When I use either the left front door, window up/down switch, or the driver side up/down control, for the left front door, I can hear the switch...


USUALLY POWER WINDOW PROBLEMS ARE ONE OF THREE THINGS. 1. SWITCH 2. MOTOR 3. WINDOW REGULATOR. THE MOST COMMON PROBLEM THE LEXUS HAS IS THE MASTER SWITCH IN THE DRIVERS DOOR. IT CAN ALSO AFFECT THE OPERATION OF THE PASSENGER DOOR SWITCH....IF WINDOW REGULATOR IS BAD YOU WILL HEAR SOME CRAZY NOISES COMING OUT OF DOOR PANEL...VERY OBVIOUS.... FOLLOW THIS CLOSELY...STARE AT A LITE DOME LIGHT USUALLY WITH DOOR OPEN...WHEN YOU PRESS WINDOW SWITCH, IF THERE IS ANY DIMING OF DOME LIGHT....MOTOR IS BAD. IF DOME LIGHT STAYS THE SAME BRIGHTNESS... SWITCH IS BAD... EXCEPT IN THE CASE SOME HACKER HAS BEEN IN THE DOOR PANEL BEFORE ...IT DOES TAKE A SPECIAL TALENT TO REMOVE DOOR PANELS WITHOUT BREAKING THINGS AND EVEN MORE TALENT TO REPLACE WINDOW REGULATORS

Aug 21, 2009 | 2003 Lexus RX 300

1 Answer

Window fell down in door


window regulaotr cable broke. Need ane regulator. go to tascafordparts.com for discount price. Do not use a used one.

Front Door Window Regulator Motor Removal and Installation
  1. Raise the front door window glass to the full up position.
  1. Remove the front door trim panel. For additional information, refer to Section 501-05 .
  1. Remove the door speaker.
  1. Position the watershield aside.
  1. sxj~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure the electrical connector is positioned aside before drilling.
    To access the power window motor bolts, use a 19 mm (3/4-in) hole saw with a 8 mm (1/4-in) pilot to drill three holes at the existing drill dimples on the door.
cc3b152.gif
  1. Disconnect the front door window regulator electrical connector.
  1. Remove the bolts and the front door window regulator motor.

Jul 02, 2009 | 1999 Ford Expedition

1 Answer

Front right door window will not go up or down, it is electric. it works, some times, and some times not. it is in the down position. Would like to move to up position. I live in Arizona, I need it up for...


does it act the same whether you use the driver door switch or the passenger door switch? Please rate as fixya if this helps. thanks

here's repair procedure

Window Regulator, Front Door, Explorer Removal
srk~us~en~file=ani_caut.gif~gen~ref.gif WARNING: IF THE REGULATOR COUNTERBALANCE SPRING MUST BE REMOVED OR REPLACED FOR ANY REASON, MAKE SURE THAT THE REGULATOR ARMS ARE IN A FIXED POSITION PRIOR TO REMOVAL TO PREVENT POSSIBLE INJURY DURING C-SPRING UNWIND.
  1. Remove front door trim panel and front door trim shield . Refer to Section 01-05B .
Trim Panel, Front Door, Explorer Hi-Series, Two-Door and Four-Door Removal and Installation
  1. Remove the two screws retaining the front door trim panel (23942) located above the window regulator handle (23342) . Also remove one screw in the upper front portion of front door trim panel .
  1. Remove inside door handle cup (22634) at the window regulator handle using a screwdriver or sharp object. Retention nibs will flex for easy removal.
  1. To remove window regulator control switch (14529) and outside rear view mirror control (17B676) , use notch located at lower end of outside rear view mirror control using a screwdriver to lift and remove.
  1. Remove outside rear view mirror control from front door trim panel pulling wire harness from inside of front door trim panel .
  1. From bottom of outside rear view mirror control, remove two screws and disconnect connector from switches. NOTE: Do not pull on the front door trim panel to remove clips from the inner panel holes.
  1. At each plastic clip location, pry the front door trim panel away from the door inner panel using the front door trim panel removing tool from Rotunda Moulding Trim Kit 107-00401 or equivalent. NOTE: Pay special attention to the cut-out in the door trim panel for the door handle, so that it clears the handle during removal without breakage.
  1. When wiring and disengagement of trim clips is completed, it is recommended that to remove panel, lift slightly to remove flange at the top of door trim panel from trough in the glass weatherstrip.
  1. Disconnect socket and bulb from illuminated interior lamp (13776) before total removal of front door trim panel. For installation, follow removal procedures in reverse order. Replace any bent, damaged or missing plastic clips on the front door trim panel to the front door trim panel , firmly loading clips into slots provided on front door trim panel .

    Trim Panel, Front Door, Explorer Hi-Series Four-Door

    a9ce4e4.gif
  1. Remove inside door belt weatherstrip and glass stabilizer.
  1. Remove front door window glass as described in this section.
  1. Remove two nut and washer assemblies attaching the equalizer bracket.
  1. Remove three rivets (manual) or four rivets (power) attaching the regulator base plate to front door trim panel finish panel (23712) .
  1. Remove window regulator electric drive and front door window channel bracket from vehicle.
  1. Working on a bench, carefully bend tab flat to remove arm slides from front door window channel bracket .
  1. Install new window regulator electric drive arm plastic guides into front door window channel bracket and bend tab back to 90 degrees. Use care not to break tab; if tab is cracked or broken, replace front door window channel bracket . Make sure rubber bumper is installed properly on new front door window channel bracket , if replacement is made.

    9b5ccd1.gif

Installation
NOTE: The front door window channel bracket and window regulator electric drive are installed into the vehicle as one assembly. The front door window channel bracket may be disassembled from the window regulator electric drive as described in Steps 7 and 8 of Window Regulator, Removal.
  1. Install front door trim panel finish panel with preassembled glass bracket into vehicle. Set the regulator base plate to window regulator electric drive using base plate locator tab as a guide.
  1. Install three (manual) or four (power) rivets (385189-S100) to attach regulator to front door trim panel finish panel . Two 1/4-20 x 1-inch bolts and two 1/4-20 nut and washer assemblies may be used as alternates for glass retention. However, torque must not exceed 4-7 Nm (3-5 ft-lb). Equivalent metric retainers may be used.
  1. Install equalizer bracket.
  1. Install inside door belt weatherstrip and glass stabilizer.
  1. Lower regulator arms to access holes in front door trim panel finish panel . Install front door window glass as outlined.
  1. Adjust glass to ensure proper alignment with glass run. Cycle glass for smooth operation.
  1. Install front door trim panel and front door trim shield . Refer to Section 01-05B .

Apr 20, 2009 | 1994 Ford Explorer Limited

Not finding what you are looking for?
2005 Chevrolet Equinox Logo

Related Topics:

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...