Question about Mercedes-Benz E320

Open Question

Remote control key fell apart how do you reassemble?

Posted by on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Nzero
  • 78 Answers

SOURCE: cigarette lighter

you will need to buy a new one. must have been one heck of a bump. make sure your plastic shroud isnt cracked whilst you have the lighter out.

Posted on Aug 31, 2008

TDISLine
  • 1874 Answers

SOURCE: column apart need to see

Please specify your car type & MY !

Example:
1992 Chevy Lumina 3.1 Liter Tilt Steering Wheel Disassembly

This procedure describes the disassembly of the steering wheel (Tilt) for a 1992 Chevy Lumina sedan. The purpose of this disassembly was to replace the RAKE. The rake moves the ignition switch mechanism when the key is turned. This system entails four major parts:

  • Key Lock Assembly
  • Rake
  • Rake to Ignition Switch actuator linkage rod
  • Ignition Switch assembly

While this procedure describes the disassembly of the tilt steering wheel for a 1992 Chevy Lumina sedan specifically, most all GM tilt wheels are the same so this procedure will work on almost all GM products. Remember that these are general instructions. For more detailed instructions pertaining to your specific vehicle, consult the appropriate repair manual

As always, you should be very careful when removing the air bag module if your vehicle is equipped with one.

WARNING: The Diagnostic Energy Reserve Module or Sensing and Diagnostic Module (DERM/SDM) can maintain enough voltage to cause air bag deployment for up to two minutes after the ignition switch is turned off and the battery is disconnected. Servicing the SRS system during this period may result in accidental deployment and personal injury.

  1. Disarm system as described in Air Bag System Disarming & Arming.
  2. Remove module attaching bolts from rear of steering wheel.
  3. Rotate horn lead ΒΌ turn and disconnect.
  4. Disconnect inflator module electrical connector, then remove module from steering wheel.
  5. Reverse procedure to install, noting the following:
    • After completing installation, rearm system as described in Air Bag System Disarming & Arming.
    • Turn ignition switch to ON position and verify that the Air Bag or SRS warning lamp flashes seven to nine times and then turns off.

Disabling the SIR System:

  1. Ensure front wheels are pointed straight ahead.
  2. Turn ignition switch to LOCK position and remove key.
  3. Remove AIR BAG fuse (No. 21 on 1995-96 models) from instrument panel fuse block.
  4. Remove trim panel from under steering column.
  5. Disconnect Connector Position Assurance (CPA) and yellow 2-way connector at base of steering column.
  6. Open glove compartment door and disconnect passenger side Connector Position Assurance (CPA) and yellow 2-way connector.
  7. Wait at least 2 minutes before proceeding with diagnosis or service.

Enabling the SIR System:

  1. Turn ignition key to the LOCK position and remove key.
  2. Open glove compartment door and connect yellow 2-way connector and Connector Position Assurance (CPA).
  3. Connect yellow 2-way connector at base of steering column, then install Connector Position Assurance (CPA).
  4. Install trim panel under steering column.
  5. Install AIR BAG fuse (1995-96 fuse 21) into instrument panel fuse block.
  6. Turn ignition key to the RUN position and verify that the AIR BAG/INFLATABLE RESTRAINT warning lamp flashes seven times and then turns off.

Okay, let's get to work! First we need to remove the steering wheel.

Note: Information provide here is by an average "back yard mechanic" with minimal professional training. So any information is taken at your own risk. But maybe this will help.



5a39cad.gif
Figure 1

1. Remove the steering wheel nut. Figure 2. (1)
2. Remove the spring clip with remover. Figure 2. (2)
3. Unplug the horn connector. Figure 2. (3)
4. Snap the horn cover off by pulling upwards. Figure 2. (4)


cb14995.gif
Figure 2

5. Remove the steering wheel with a steering wheel puller. Do not use a hammer to bang on the end of the shaft.

bf97a30.gif
Figure 3

6. Push in and turn counterclockwise to remove horn wire. Figure 4. (1)
7. With the steering wheel removed, lift off the horn continuous connection mechanism and turn signal canceling arm. Figure 4. (2)


42b57f1.gif
Figure 4

Removing The Column Housing Cover

2a61a2e.gif
Figure 5

To remove the turn signal handle, remove the screw indicated. Figure 5.


2a341e8.gif
Figure 6

Remove the turn signal mounting top torx screw. Figure 6.


9585ae1.gif
Figure 7

Remove the turn signal mounting bottom 2 torx screws. There is one more torx screw to the left of this one. Just below the turn signal handle screw. Figure 7.


078ba7d.gif
Figure 8

Remove the hazard button mounting screw. Figure 8.


1b6291c.gif
Figure 9.

If you look in this area, Figure 9, there is a "V" cut out. Use a thin flat blade screwdriver. Insert about 2�" and lightly pry down (handle of screwdriver up). This will release the safety tab and allow the column housing cover to be removed.

Pay attention to the upper right hand screw mounting hole. This might catch while trying to remove the column housing cover. Lift off the column housing cover from the Right.

While the column housing cover is free, the turn signal handle can be feed through it's cut out in the Housing by rotating the column housing cover 180 degrees to allow the washer tab on the handle to fit through.




Steering Column Component Diagram


52645f7.jpg

e187857.jpg

Posted on Oct 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need a diagram of how the Rear brakes are reassembled. When we removed mine they fell apart.


buy a repair manual at any auto parts store and it will explain all you need .

Jun 14, 2015 | Cars & Trucks

2 Answers

How do I replace the battery on a key remote for a Mazda cx9 year 2012


Flip open key. With small tweezers, file, or jewellers screwdriver, depress release button found in key-slot (near the end of the fob with the key on it. Pull two halves of fob apart. Separate the remaining fob in half again (the part without the key) by prying in the slot on the open end. Replace battery. Reassemble.

Jan 27, 2015 | Mazda CX9 Cars & Trucks

1 Answer

ML 320 Remote Control doesn't function


Have you tried replacing the battery in it?

Jan 16, 2015 | 2001 Mercedes-Benz ML 320

1 Answer

Remote for appollo 1996 fell apart need to know how to reassemble


Replace it, they don't provide repair instructions for this type of device.

Nov 05, 2012 | Cars & Trucks

1 Answer

Ignition module fell apart


u need a repair manual-online or in library--it may not be fixable -they wear out-car is 20yr

Jun 05, 2012 | 1992 Geo Storm

1 Answer

2004 Isuzu Axiom with 29000 miles on it. The key fob fell apart and out fell the insides-so I've been using the key without the remote. Sometimes if I open any other door than the driver door the vehicle...


If it was factory fitted You will have to contact isuzu with the V.I.N. and proof of ownership they will get a new fob for you. If it's after market then you can either get a new fob and get it programed or get the imobiliser disabled

Sep 15, 2009 | 2004 Isuzu Axiom

1 Answer

How do you replace the battery in the remote control with key?


the switchblade key comes apart buy lightly prying the 2 halves apart with a pocket screwdriver then the half that has the buttons will pop apart like a watch the battery is a watch/hearing aid battery, think the number is c2023

Mar 15, 2009 | 2004 Volkswagen New Beetle Convertible

1 Answer

PROGRAMMING REMOTE FOR 2002 OPTIMAA


dealer only and yes it does have a chipped key

Dec 31, 2008 | 2002 Kia Optima

1 Answer

Cigarette lighter


you will need to buy a new one. must have been one heck of a bump. make sure your plastic shroud isnt cracked whilst you have the lighter out.

Jul 29, 2008 | 1995 Subaru Legacy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75077 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...