Question about 1984 Ford F 150

1 Answer

How do I remove the drive shaft bearing on the split drive shaft- this is a 1984 ford and the bearing appears to be pressed on- What can I do to take this ****** off as it was not working corrrectly untill I started spraying lub in it

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 333 Answers

If your geting a new on. Take a grinder with a cutoff disk. Or a dremel tool, Hacksaw whatever you got and cut the bearing on both sides almost to the driveshaft. Then take a hammer and chisel and pop it real good. And call it a dirty ***********. And it fall off. Or you can just stand the driveshaft on a block of wood and tap the bearing around and around straight down. Maybee heat it up with a tourch and hit it some more. but it will go.

Posted on May 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front diff.seal leaks


Remove the front drive shaft remove the drive yoke off the pinion shaft remove the old seal install new seal install front drive shaft. PS check pinion bearing play before removing drive yolk. if it is loose then you might also need bearings

Oct 21, 2015 | Ford Explorer Cars & Trucks

1 Answer

I'm getting ready to replace propeller shaft center bearing on 07 frontier crew cab 2 wheel drive. is bearing pressed on or can it be replaced with out press?


You can use a long drift punch to knock the old one off. I use a piece of pipe that is the same size as the inner bearing race and drive it back on.

Jan 01, 2015 | Cars & Trucks

1 Answer

Replace brake hose nissan patrol


The bearings in your car are pressed into a hub. If the part is available as an assembly, it can be replaced that way. Generally on a front drive car:
Remove wheels and brake calipers
If it is pressed in: remove the rotors, disconnect the drive shafts and remove the steering knuckle. Then the old bearing is pressed out and the new one pressed in with a machine shop press. If the bearing is part of the hub, that will be unbolted and the new one swapped.

Sep 11, 2012 | Cars & Trucks

1 Answer

How do I remove the front drive shaft of a 2001 Ford Ranger double cab UK model, 2.5 turbo diesel


if it were me i would just get a new cv axle they went down alot on prices and by the time you **** around putting an after market boot on you will spend about the same money further more usually when the boot is split the bearings are already damaged

Nov 16, 2011 | Cars & Trucks

2 Answers

Loud clanking sound from underneath the truck. Took it in and the tech said the driveshaft bearing is shot. He says this is what's causing the driveshaft to vibrate causing the clanking sound. He says the...


Does "clank occur when shift fwd/rev ? Worn U joint. Can be hard to change. DIYrs bash it out with hammer(after removing driveshaft from truck) Techs use press. These trucks prone to rear flange splitting @ U joint cap. Drive shaft bearing ? :"It dont got 1" Pinion bearing in diff supports driveshaft. sometimes pinion flange nut backs off, but usually worn pinion bearing causes it to seem that way.
Block wheels,trans in neutral,crawl under and rotate shaft by hand. Listen for noise.Follow sound to movement( there should be ALMOST none.Where 1 part moves and the part attached doesnt,,theres your prob. btw "drive shaft bearing USED to be a joke.

Jan 06, 2011 | 2004 Ford F150

1 Answer

How to change the rear bearings in my 1997 grand cherokee limited


YOU HAVE TO SAFELY RAISE SUPPORT VECHICLE MAKE SURE ITS ON A SOLID LEVEL GROUND.THEN YOU REMOVE THE WHEELS THE BRAKE DRUM OR DISC.THEN YOU REMOVE THE NUTS THAT ATTACH THE OUTER SEAL RETAINER AND BRAKE BACKING PLATETO THE AXLE SHAFT TUBE.DISCARD THE NUTS.REMOVE AXLE SHAFT FROM HOUSING.WITH AN AXLE PULLER ATTACHED TO A SLIDE HAMMER.DISCARD INNER AXLE SEALPOSITION THE AXLE SHAFT IN A VISE.REMOVE THE RETAINING RING BY DRILLING A 1/4 HOLE ABOUT 3/4 OF THE WAY THROUGH THE RING. THEN USING A COLD CHISEL OVER THE HOLE.SPLIT THE RING.REMOVE THE BEARING WITH A ARBOR PRESS DISCARD THE SEAL AND REMOVE THE RETAINER PLATE.TO INSTALL - CLEAN THEN APPLY A THIN COATING OF WHEEL BEARING LUBRICANT TO THE BEARING AND SEAL CONTACT SURFACES APPLY WHEEL BEARING LUBRICANT TO THE LIPS OF THE REPLACEMENT INNER AND OUTER SEALS.INSTALL THE INNER SEAL WITH THE OPEN END OF THE SEAL FACING INWARD ENSURE IT IS COMPLETELY SEATED.INSTALL THE RETAINER PLATE AND THE OUTER SEAL ON THE SHAFT.ENSURE THE OPEN END OF THE SEAL FACES TOWARD THE AXLE SHAFT BEARING.PACK THE REPLACEMENT BEARING WITH WHEEL BEARING LUBRICANT AND POSITION ON THE AXLE SHAFT PRESS INTO PLACE.PRESS A REPLACEMENT BEARING RETAINER ON THE AXLE SHAFT AGAINST THE BEARING.INSTALL THE AXLE INTO THE AXLE TUBE.POSITION AND ALIGN THE SEAL RETAINER AND BRAKE SUPPORT PLATE AND INSTALL REPLACEMENT ATTACHING NUTS.TIGHTEN NUTS TO 32 FT LBS.INSTALL BRAKE ASSEMBLY WHEELS LOWER VECHICLE. YOU SAID REAR BEARINGS IF THIS WHAT YOU MEANT.I HOPE THIS CAN HELP.

Apr 12, 2010 | 1997 Jeep Grand Cherokee

1 Answer

1986 chevy s10 trying to remove center bearing on


theres a collar on the youk.remove it and tap it out its splits the tow pieces of drive shaft.use alot of pb blaster and make sure you grease the youk theres a grease fitting there

Mar 27, 2010 | 1998 Chevrolet S-10 Pickup

1 Answer

Leaking rear axel seal


  1. Remove or disconnect the following:

    Rear wheel Brake caliper and rotor, if equipped Brake drum, if equipped Axle retainer nuts Axle shaft, seal and bearing assembly
  2. Split the bearing retainer with a chisel and remove the retainer ring.
  3. Press the bearing off the axle shaft.
  4. Remove the axle seal and retaining plate.
0900c15280220349.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Rear axle seal and bearing components-2002-05 exc. 2005 Grand Cherokee Hope this helps, please dont forget to rate my solution.



Lefty64

Apr 09, 2009 | 2002 Jeep Grand Cherokee

1 Answer

Carrier bearing removal on a 2000 f250


Remove the drive line. Split the drive shaft apart and then do as you guessed and remove the nut. Then you can get the carrier bearing off.

Mar 15, 2009 | 2000 Ford F250 Super Duty Crew Cabs

2 Answers

I paid for an answer about my 89 ford ranger drive shaft and did not get one. Can I get my money back or do I need to contact Pay-Pal??


To replace the centre bearing you first remove driveshaft from vehicle.
Pull the shaft apart at the middle universal joint.
On the back of the section that has the centre bearing you will see a nut that holds the uni ears onto the shaft.
Undo the nut and remove the ears. Then press the centre bearing off the shaft and reassemble with new one.
Hope this is more helpful.

Jan 01, 2009 | 1991 Ford Ranger Supercab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...