Question about 2001 Toyota Sienna

1 Answer

Back seat belt will not retract how do I get into the seat belt housing to fix it? thanks Dave

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 160 Answers

Dave I highly reccomend you to replace the seatbelt instead of repairing it ...you wouldnt want it to fall in an accident... the dealer dont repair them for this reason

Posted on May 05, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fix a rear seat belt that wont retract 2002 tauras


you may have to remove the seat to gain access to the belt housing. inside there is a roller that spindles the belt to retract. they are easy to replace. i would advise going to a junk yard to get one that still works and use it. they are sometimes expensive. should just have a few bolts to remove the bracket from the floor and then one or two bolts from the top bracket.

Jan 15, 2015 | 2002 Ford Taurus

1 Answer

Remove seat belt


Hi Ray, Removal of the seat belts requires removal of the seats. Adjust the front seats to the fully backwards position and remove the fixing bolts and then unhook rails at the rear.You will notice a wire cable attached to each seat used to adjust the belt shoulder hight. This must also be disconnected. On later model vehicles there is an automatic retraction unit which pulls the driver and or passenger back into the seat in the event of the air bags being deployed. These connections must also be removed. If seats are electrically operated unplug all connectors. Remove seats and then gently remove plastic door pillar covers. (These are in two pieces for each front belt.) Removal will leave the fixing bolts of retractable part of the seat belt exposed. The buckle side is fixed with one bolt and has an electrical connection which must be disconnected. Hope this is of help? Regards John

Oct 27, 2013 | BMW Z4 Cars & Trucks

1 Answer

Seat belt retractor locked


Seat belts are not fixed they are only replaced.

Aug 28, 2013 | 1998 Saturn SL

1 Answer

How do I release the rear seat belt that is stuck to the back of the chair


you will have to be patiant with this as long as the seat belt tensioners havent gone try to pull the belt so some tension comes of it so it can roll back into the spool or jiggle it by bulling on it quickley should be a simple fix hope this helps

Aug 18, 2012 | 2007 Hyundai Santa Fe Limited

1 Answer

How to fix a stuck seat belt VW GTI 2009


I just solved the problem for a stuck rear center seat belt in my 2002 Jetta.

Flip the base seat cushion forward against the front seat backs. Trace down along the belt to its tether point on the floor. The belt is sewn around a steel loop. The loop is anchored to a black steel hook. A thin silvery retainer plate is spring tensioned on top of the loop to prevent it from sliding off of the hook when the seat back is folded.

Therefore, you need to press the silvery retainer plate away from the hook (push up) to allow the loop to be slid from the hook. The belt was tight with the seat back in the upright position, so it was necessary to fold the seat back forward to create slack in the belt. Now push the belt loop towards the trunk and slide it off of the end of the hook (only possible with the retainer plate pushed up out of the way).

Now with total release of tension on the system via the bottom end of the seat belt being untethered and with the seat back returned to the upright position, normal extension and retraction of the belt will be reestablished. Next, simply extend the seat belt and slide the loop back into place over the floor hook. It snaps past the silvery retainer plate without all the effort required to hold the plate up during removal of the loop during disassembly.

Check again, the seat belt should be extending and retracting properly. Now just put the seat cushion back into regular position and you will be able to safely buckle up three people across the back seat.

It took about as long to do this repair as it has taken to post this answer to the problem. Note, the seat belt safety mechanism only allows normal extension and retraction of the belt when the seat back is upright.

Nov 29, 2009 | Volkswagen GTI Cars & Trucks

1 Answer

My front side seat belt on my 1998 was pulled to far out and now wont retract back.What can I do/thanks


You'll have to remove the trim on the side of the car in order to access the seat belt tensioner. You can adjust it with a screw driver and retract it back..

Sep 17, 2009 | 1998 Chrysler Sebring

1 Answer

Seat belt will not retract. how do i fix it?


The mechanism that allows it to retract is broken. Replace the seat belt.

Jul 15, 2009 | 2004 Dodge Grand Caravan

1 Answer

99 Toyota Camry one of the rear seat belts won't retract


You have to actually unbolt the belt holder behind the seat. Then from there you can check to see if the spring still works. You'll probably have to take the cap off it, wind the spring-load, then put the cap back on. If you can get to it, it's not too difficult. I recommend another pair of hands to help hold if they're available. You'll also want to make sure you've rolled the belt up as much as possible before before you coil the spring-load.

Apr 25, 2009 | 1999 Toyota Camry

1 Answer

Seatbelt won't retract


1)move the plastic cover over the seat belt out of the way to gain access to the two mounting bolts for the seat belt mechanism. Use a 10mm wrench and a 14mm wrench and remove the two bolts holding the seat belt mechanism to the body. Use a small drill bit or small screwdriver and make one hole in the plastic cover on each side of the seat belt mechanism (the covers say "do not remove plastic cover". Spray lots of wd40 in each hole. Then exercise the seat belt. When the mechanism allows the belt to be retracted, retract the belt all the way out and exercise the seat belt. Reinstall mechanism with both mounting screws in original position and put plastic cover back in place. Good luck. New seat belt costs $100.00 from dealer and are hard to find working in junk yards. I have fixed several of them this way.

Jan 17, 2009 | 1996 Toyota Corolla

1 Answer

Seat belt malfunction


There may be a small object like a coin in the re-tractor, pull the re-tractor and check, if nothing is found you will have to replace the belt assy, they are not repairable.

Sep 02, 2008 | 2001 Honda Odyssey

Not finding what you are looking for?
2001 Toyota Sienna Logo

316 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...