Question about 1994 Dodge Colt

1 Answer

Blew timing belt on 1994 dodge colt. Where are the timing marks on the gears.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Dodge Master
  • 1,757 Answers

Click on the following: direct, free Link. It has the Timing Belt Marks for your 1994 Dodge Colt; with the unspecified 1.5L or 1.8L SOHC In-Line 4-Cylinder Engines.
After looking at the Diagrams, if you are having a problem with locating the marks on the Cam Sprocket LOOK at the Camshaft Key location at the center of the Camshaft Sprocket Bolt in relation to where the Mark should be.
There are several additional diagrams on the Link Page which will be help you in your endeavors.

Let me know if this helped.

Posted on May 05, 2010

Testimonial: "Thanks very very helpful"


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Change timming belt. where marks have to be set? 92 dodge colt

I lost you, stupid computer. Anyhow there are 8 different engines for the dodge colt in the early 1990's I can only assume its the 1.4L, 1.5L or 2.4L. The 1.4L & 1.5L the timing marks are exactly the same. The Cam points to 3:00 marks ther. The crank points almost straight up, slightly to the right, mark on engine cover. The 2.4L has 3 marks, The crank has an alignment mark at approximately 10:00, the cam sprocket points straight up at 12:00 and the idler pulley (to the right of crank shaft pulley) points approximately 11:00. They should all have a notch or mark when aligned. The short secondary belt, the crankshaft should be in the same location 10:00 and the balance shaft (to the left) should be at 9:00. This goes on after of course. Rotate engine 2 full revolutions and recheck marks before starting engine.

Feb 02, 2011 | 1992 Dodge Colt

1 Answer

I have a 1994 Ford Ranger 2.3L with a broken timing belt and need to know the timing piont for the oil pump gear.

2.3L engine only has an internal oil pump, inside oil pan, driven by camshaft, no sprocket for oil timing belt, only timing mark for crankshaft and camshaft gear's, timing belt tensioner and auxiliary gear's no timing marks.Hope this was very helpful.


Aug 19, 2010 | 1994 Ford Ranger Supercab

1 Answer

Timing marks for the Dodge 2.4L caravan, 2000

To align both sets of timing marks, turn engine crankshaft to the right with belt on cam and crank. Once you have done this the crankshaft alignment mark (on front of crankshaft gear) will line up with mark to the rear of gear on engine block.The two cam gear timing marks should be alines across from one another. The right cam gear is the intake side and the left side is the exhaust side. After removing the belt turn the exhaust cam down 1/2 notch. Timing mark on exhaust 1/2 notch down from the intake side. Install new belt and recheck everything to make sure it's all correct. Hope this will help you.

May 16, 2010 | 2000 Dodge Caravan

1 Answer

Replace timing belt on 94 dodge stealth 3.0 dohc need to know everything to replace timing marks and route of belt

timing marks are easy to see,(on the top of gears and line up with the metal indents above them) change the water pump it idles on it... you need a cam holder to hold your cam gears in place when changing they will spin when you take off the old belt... it is an easy timing belt for a *** V6...!

Apr 06, 2010 | 1994 Dodge Stealth

1 Answer

How to replace 1987 Dodge Colt water pump

Rear Wheel Drive:

1. Open the radiator petcock and the engine drain plug on the passenger's side. Drain the cooling system. Disconnect the battery ground (negative) cable.
  1. Remove all drive belts, pump mounted cooling fan/or drive pulley, and the alternator brace.
  2. Unscrew the retaining nuts and bolts. Remove the water pump.

To install:
  1. Install a new gasket on the timing gear cover with sealer.
  2. Apply sealer to the mating surface of the water pump. Install the pump. Tighten the nuts and bolts gradually in a criss-cross pattern to 11 ft. lbs. Don't overtighten the fasteners, the pump is aluminum.
  3. Spin the pump to make sure that it doesn't interfere with the case.
  4. Install the fan.
  5. Install and tension the drive belts.
  6. Refill the cooling system with a 50/50 mixture of antifreeze and water.
FRONT Wheel Drive:

  1. Drain the cooling system.
  2. Remove all drive belts and water pump pulley. It may be necessary to remove an engine mount, the power steering pump and alternator brace to gain necessary clearance, depending on model.
  3. Remove the timing belt covers and timing belt tensioner, and timing belt.
  4. Remove the water pump bolts.
  5. Remove the water pump.

To install:
  1. Discard the O-ring in the front end of the water pipe. Install a new O-ring coated with water.
  2. Using a new gasket, mount the water pump. Torque the bolts with a head mark 4-10 ft. lbs.: the bolts with a head mark 7-20 ft. lbs.
  3. Assemble the remaining components, install the timing belt. Fill the system with a 50% mix of antifreeze.
Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Feb 25, 2010 | 1987 Dodge Colt Vista Wagon

1 Answer

1990 dodge colt 1-5 broken timing belt, trouble

possibly bent a valve when the timing belt broke, check compression!!!!!!

Feb 01, 2010 | 1990 Dodge Colt Vista

1 Answer

I am putting a new timing belt on a 1990 colt vista with a 2.0 liter engine.I need to know the timing mark positions.

On cam gear there's a punch mark, line that mark at 9 oclock there's a timing mark on cylinder head, crank gear, in back of crank gear is a plate with a (v) cut line gear at 11 oclock there's a timing mark on front case, gear to right of crank gear has a (v) cut on it, line it at about 11 oclock at timing mark on front case, adj tensioner and your done.Good Luck.

Dec 12, 2009 | 1990 Dodge Colt Vista

1 Answer

I need timing specs for 1994 dodge intrepid 3.5 For a new timing belt I need to know how to align the gears and crank shaft.

Crankshaft sprocket mark aligns with TDC indicator just above it, and camshaft mark, goes in center of 2 marks on back cover behind them.05fb1b8.gif

Oct 31, 2009 | 1994 Dodge Intrepid

1 Answer

We lost reverse and neutral in a 1994 dodge colt. We are trying to adjust the linkage under the hood. still drives but when in park/reverse and neutral rev's sound bogged. any hints


Sep 07, 2009 | Dodge Colt Cars & Trucks

Not finding what you are looking for?
1994 Dodge Colt Logo

602 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

79847 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides