Question about 1992 Oldsmobile Cutlass Supreme

1 Answer

My 92 cutlass supreme is spitting antifreeze e from water pump?

My 92 cutlass supreme is spitting antifreeze from the serpentine belt, I think the water pump might be leaking but not sure

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 395 Answers

Could be the upper hose best way to know it use a pressure test on the raidator

Posted on May 05, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What makes the fuel pump not kick on on a 92 Oldsmobile Cutlass


There is a red wire close to the battery in the front. It's not connected to anything. Apply positive voltage and that will run your pump for testing purposes.

Dec 08, 2015 | Oldsmobile Cars & Trucks

1 Answer

'92 cutlass ciera 3.3 belt tensioner assembly replacement


your belt has to come off the ensioner should have one bolt to loosen

Jan 22, 2014 | Cars & Trucks

2 Answers

How do you change a water pump


Hello,

To replace the water pump of the 1993 oldsmobile cutlass supreme, please follow the steps below:
  1. Disconnect negative battery terminal from battery.
  2. Drain coolant...if new save and reuse. If not replace it with premix 50/50 antifreeze. You can mix your own but for convenience use the 50/50.
  3. Remove air cleaner (if located in the way), and remove Radiator overflow tank.
  4. Remove serpentine belt and tensioner. (rotate tensioner counter clockwise to release belt tension (write down routing of belt before removing)and remove the belt from the auxilliary components and slowly release the tensioner. On 3.1 and 3.4L engines remove tensioner retaining bolt and detach tensioner assembly from the engine.
  5. Remove alternator and its brackets (AC compressor if necessary)
  6. Remove small belt guard just above water pump (on 3.1L)
  7. Remove water pump mounting bolts (around the perimeter of the pump- approximately 5 of them) and remove the pump. If it is stuck tap with a SOFT-face hammer GENTLY!!!
  8. Clean fastener threads and any threaded holes in the engine to remove corrosion and sealant. Remove any residual gasket material left on block
  9. Use Lacquer thinner or acetone to clean the engine and water pump surfaces that will come into contact with each other.
  10. Apply NEW gasket if not attached to H2O pump
  11. Attach pump and gasket to engine block and start the bolts finger tight Tighten in 1/4 turn increments to torque Torque for 3.1 and 3.4L is 89 in-lbs....THIS IS NOT VERY HARD!!! TIGHTEN WITH SOCKET AND RATCHET TILL 1/2 TURN PAST TIGHT!!!!!
  12. Reinstall all parts you took off to get to this darn thing.
  13. Try to make sure, while doing these, You will try ta ask for assistance from Your friends.
Hope this helped. Thank You for using FixYa!!!

Jan 17, 2011 | 1993 Oldsmobile Cutlass Supreme

1 Answer

I have a 1990 supreme cutlass and i don't know how to change the serpentine belt. What do I do?



2.8L and 3.1L Air Pump Belt

  1. Disconnect the negative battery cable.
  2. Loosen the air pump.
  3. Remove the worn belt.

To install:
  1. Adjust the belt to specifications and tighten the pump mounting bolts.
  2. Connect the negative battery cable.

2.3L Power Steering Belt
  1. Disconnect the negative battery cable.
  2. Loosen the adjustment bolts.
  3. Remove the power steering belt from the pulley.

To install:
  1. Route the belt around the pulley.
  2. Adjust the belt to specifications, then tighten the adjustment bolts.
  3. Connect the negative battery cable.

See Figures 6 through 15

0900c15280067989.jpg

Fig. Fig. 6: Unfasten the retaining bolts...


0900c1528006798a.jpg

Fig. Fig. 7: ... then remove the serpentine belt guard


0900c1528006798b.jpg

Fig. Fig. 8: ...


0900c1528006798c.jpg

Fig. Fig. 9: ... then remove the serpentine belt

  1. Remove the belt. Clean the accessory drive belt surfaces.



0900c1528006798d.jpg

Fig. Fig. 10: Serpentine drive belt routing-2.2L engine


0900c1528006798e.jpg

Fig. Fig. 11: Removal and installation of the serpentine belt-2.3L engine


0900c1528006798f.jpg

Fig. Fig. 12: Serpentine belt routing-2.5L engine with and without A/C


0900c15280067990.jpg

Fig. Fig. 13: Use an 18mm box end wrench on the pulley nut to rotate the tensioner on the 3.8L engine


0900c15280067991.jpg

Fig. Fig. 14: in. breaker bar to rotate the tensioner


0900c15280067992.jpg

Fig. Fig. 15: On the 3.4L, use a box end wrench, then rotate the tensioner clockwise and remove the serpentine belt

Remove the belt guard or coolant recovery reservoir as required.



Dec 31, 2010 | 1994 Oldsmobile Cutlass Supreme

1 Answer

I have a 1994 Olds Cutlass Supreme overheating


If it's the water pump, you should be able to see it dripping just behind the pulley. The seal on the water pump is usually what goes. If there is antifreeze drips all over the front of the engine, and it drips a bit after you shut it off, it likely is the water pump.
If it runs poorly when you first start it in the morning, however, you could still have a head gasket problem. If that is the case, you will see a lot of white exhaust, which is the cylinder blowing the antifreeze out. One thing you can do is run it with the rad cap off, and see if it continues to bubble. If it does, then your head gasket is leaking. I am assuming it is a V6, so keep in mind that you have 2 head gaskets. The other oine could be gone now if it wasn't replaced.

Apr 05, 2010 | 1994 Oldsmobile Cutlass Supreme

1 Answer

Where is the water pump located on the 3.4 liter


Water Pump location above your A/C compressor.
Left corner of radiator
To remove and Replace take 1Hour 30 minute.
Or a little fast.

Remove air cleaner assembly
Disconnect battery ground cable, ( your call ).
Drain coolant
loosing the bolt only on the water pump pulley
Remove the Serpentine belt
Then take the bolt completely out.
and there is your Water pump.

Let me know....

Sep 20, 2009 | 1996 Oldsmobile Cutlass Supreme Coupe

1 Answer

How to replace serpentine belt diagram 1997 olds cutlass


Have you checked under the hood, should be a belt diagram some were around the fan shroud .

Sep 07, 2009 | 1997 Oldsmobile Cutlass Supreme

2 Answers

Replacing water pump on a 94 cutlas supreme instructions



REMOVAL & INSTALLATION


CAUTION When draining the coolant, keep in mind that cats and dogs are attracted by ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or inPuddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.
2.2L Engine
  1. Disconnect the negative battery cable.
  2. Properly drain the engine coolant into a suitable container.
  3. Remove the serpentine drive belt, as outlined in of this repair guide.
  4. Unfasten the water pump pulley bolts, then remove the pulley.
  5. Remove the alternator and side bracket.
  6. Disconnect the water pump hoses.
  7. Unfasten the water pump retaining bolts, then remove the water pump from the vehicle. Remove and discard the gasket. Thoroughly clean all gasket mating surfaces.

To install:
  1. Position a new water pump gasket, then install the water pump. Tighten the attaching bolts to 18 ft. lbs. (25 Nm).
  2. Install the water pump pulley and secure with the retaining bolts. Tighten the bolts to 22 ft. lbs. (30 Nm).
  3. Attach the water pump hoses.
  4. Install the alternator bracket and the alternator.
  5. Install the serpentine drive belt.
  6. Properly refill the engine cooling system using the correct type and amount of coolant.
  7. Connect the negative battery cable.
6b49937.jpg

Apr 05, 2009 | 1988 Oldsmobile Cutlass Supreme

1 Answer

Water pump


To replace the water pump on this is very easy. Remove the belt, unbolt the pulley and remove it. Then unbolt the water pump mounting bolts it is that easy. Please rate.

Dec 09, 2008 | 1997 Oldsmobile Cutlass Supreme

Not finding what you are looking for?
1992 Oldsmobile Cutlass Supreme Logo

Related Topics:

185 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...