Question about 2006 Peugeot 505

1 Answer

My e7 taxi brakes are binding on sometimes callipers ok put on new master cylander same problem the car is a taxi e7 model based on the expert 2006 but not in select models

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

Behind servo in a link arm which seizes. had a few now

Posted on Feb 02, 2015

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 255 Answers

SOURCE: stiff break peddal hot breaks

what are you referring to that is still heating up ? from the info that you have give it sounds like power brake booster is leaking or loosing vacuum

hope2help shack

Posted on Apr 17, 2009

Hightower971
  • 183 Answers

SOURCE: clutch failed is it cable

Crawl under the vehicle and look at the clutch assembly. If there is a bleeder valve it's hydraulic.

Posted on Apr 26, 2009

  • 6 Answers

SOURCE: clutch will not engage. put a slave cylander, and

have you bled the system properly?

Posted on Aug 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brake binding. How do i stop this.??


on disc brakes --free up the pins that the callipers slide on
on drum brakes --install correctly and use new springs
with hand brake
adjust or replace faulty brake cable
replace faulty master cylinders

Nov 02, 2017 | Cars & Trucks

1 Answer

Kia K2700 front brakes binding, new master and load censor.


check the adjustment of the pedal for the master cylinder
the rod attached to the pedal must be free about 1" movement before the master cylinder is activated
if the pistons in the master cylinder are not free of the compensating ports tyen hot brake fluid will push on the calliper pistons and apply the brakes
the load sensor is only a proportioning valve to allow more pressure to the rear brakes under a loaded situation
you may have to take it to an accredited brake specialist shop to properly diagnose the problem

Sep 28, 2016 | Kia Cars & Trucks

1 Answer

My right front brake is locking up could this be caused by the master cylander booster? Lines calipers hoses all ok


no if it were the booster it would be all brakes not just one . daugher had one locking up and it was the hose had gone bad internally but looked fine outside .

Oct 05, 2015 | 2000 Chevrolet Chevrolet Cavalier Base

1 Answer

Should piston go all the way back where it is flush with piston outer housing?


Measure the thickness of the disc. It could be thin enough with the worn bads that the piston is coming out so far that it is binding in the bore.

Apr 23, 2014 | 2003 Toyota Celica

1 Answer

Callipers on passenger side front and rear had locked down while the car sat on millitary base for nine months. Purchased new callipers (all four) pads rotors etc to get my sons car back on the road. Now...


Sounds like the master cylinder has bailed on you as well. Pedal going to the floor is the common sign that it's bad. To prevent any more aggrevation's, match the part, port for port, size, shape, and mount flange before putting a drop of fluid in the new one. It's a critical part and should obtained from Hyundai. Have it pressure bled, or have the dealer do it. The ABS sometimes requires special equipment to bleed the system.

Aug 27, 2011 | 2006 Hyundai Tiburon

2 Answers

Horn wont work on my peugeot partner van


Check (in the order, presented below)
1. horn fuse
2. horn relay
3. horn circuit (you will need tester)
4. horn itself (remove it from car and connect to 12V DC)

May 19, 2011 | Peugeot 405 Cars & Trucks

1 Answer

After applying the brakes ten to fifteen timesthe brakes bind


Your brake fluid has absorbed some water from the air and when the fluid gets hot, the water vaporizes. Drain the fluid from the master cylinder using a squeeze bottle and a piece of tubing, refill with new fluid from a tightly sealed container, then bleed the brakes.

Sep 13, 2009 | 1995 Land Rover Defender

3 Answers

Front passenger side brake problem


i would try the perportioning valve

Aug 15, 2009 | 1993 Oldsmobile Achieva

2 Answers

Problem with brakes


the brake booster has a rubber diaphragm in it that sometimes goes out and causes that problem

Apr 21, 2009 | Dodge Ram 3500 Cars & Trucks

1 Answer

Stiff break peddal hot breaks


what are you referring to that is still heating up ? from the info that you have give it sounds like power brake booster is leaking or loosing vacuum

hope2help shack

Apr 17, 2009 | 1989 Peugeot 405

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

177 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

mike hayward

Level 2 Expert

279 Answers

lloyd cole

Level 2 Expert

250 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...