Question about 2006 Ford Expedition

2 Answers

Stumble after take off in engine of 01 expedition. No codes are coming up when hooked up to computer. All spark plugs were just changed.

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,374 Answers

Sounds like Mass Air Flow Sensor(MAF). While vehicle is running tap it lightly with a screw driver and see if there is a change in idle. Next inspect the air duct attached to it must be free of holes and cracks. The other thing you can do to see if its working properly is to restrict the flow of air going into it and measure the pulse width of a fuel injector to see if there was a change in fuel delivery. if there is a change its working.

Posted on May 05, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 5,537 Answers

Look at the old plugs for burn condition. This will show you if there are strange colors on the plugs from contaminated fuel. Do a fuel sample and change the fuel filter at the same time. Were the new plugs gapped properly? An osilliscope type of meter will show each plugs firing peak.

Use a water spray around the intake manifold to check for vacuum leaks and a vacuum gauge to see how much vacuum you are creating. If still no help, temporarily plug the EGR vacuum line. It will code, but check performance with it disconnected.

Most other electronics should code, you might have a weak spot on the TPS. It advances spark and fuel
flow and can cause stumble. Since it is a variable switch it may be bad and not code because of the wide range of opearation. They usually have to be shorted to code.

Posted on May 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

91 buick lesabre chugging at idle and accelerating smooths out at speed


It can be issue with IAC( idle air control valve) causing the problem.


There are many other possibilities causing these idle issues. Engine idles rough.

There are few help links with solutions to troubleshoot such idle issues.

I suggest you refer the link below and follow its troubleshooting details:------

Click the link below:-----

Ford Expedition IAC valve replacing

http://technoanswers.blogspot.com/2012/12/ford-expedition-iac-valve-replacing.html

Bad miss at idle?

http://technoanswers.blogspot.com/2012/01/bad-miss-at-idle.html

-----------

Stumbling and stalling at idle after engine rebuild?

http://schematicsdiagram.blogspot.in/2012/03/stumbling-and-stalling-at-idle-after.html

------------

1999 Ford F-150 Idles rough and quits when gas pedal is pressed less?

http://technoanswers.blogspot.in/2012/01/1999-ford-f-150-idles-rough-and-quits.html

---------

Engine stumbles coming off idle when warm?

http://repairhelpcenter.blogspot.com/2012/01/engine-stumbles-coming-off-idle-when.html

------------------

Erratic idle on car?

http://schematicsdiagram.blogspot.com/2011/12/erratic-idle-on-car.html

-----------


Cold start problem and vehicle shudder around 2500 to 3500 rpms

http://repairhelpcenter.blogspot.com/2012/10/cold-start-problem-and-vehicle-shudder.html

----------

Low idle when cold out side?

http://repairhelpcenter.blogspot.com/2011/12/low-idle-when-cold-out-side.html

-----------

GMC Sonoma Stalls and idles low

http://technoanswers.blogspot.com/2012/10/gmc-sonoma-stalls-and-idles-low.html

--------


GMC Idle Air Control (IAC) Valve Replacing?

http://schematicsdiagram.blogspot.com/2011/12/gmc-idle-air-control-iac-valve.html

-------------

1996 Camry intermittent engine failure while idle?

http://repairhelpcenter.blogspot.com/2011/10/1996-camry-intermittent-engine-failure.html

------------

Engine quits at idle?

http://repairhelpcenter.blogspot.com/2011/10/engine-quits-at-idle.html

-----------

Car overheats and Air blows hot at idle?

http://howtobyme.blogspot.com/2011/11/car-overheats-and-air-blows-hot-at-idle.html

---------

High Idle Problem

http://repairhelpcenter.blogspot.com/2012/10/high-idle-problem.html

-------

While stop engine idles like cylinder missing?

http://schematicsdiagram.blogspot.com/2012/01/while-stop-engine-idles-like-cylinder.html

---------

Idle flair is noticed on car? Rough idle? car will not idle? Erratic idle speed?

http://technoanswers.blogspot.in/2012/02/idle-flair-is-noticed-on-car-rough-idle.html

--------

High rpm in neutral? Inconsistant high RPM in neutral?

http://technoanswers.blogspot.in/2012/02/high-rpm-in-neutral-inconsistant-high.html

-------

Vehicle stumbling at idle and shows code 54?

http://schematicsdiagram.blogspot.in/2012/03/vehicle-stumbling-at-idle-and-shows.html

----------

Rough idle, staling and Erratic shifting?

http://technoanswers.blogspot.in/2012/03/rough-idlestaling-and-erratic-shifting.html

-----------

While stop engine idles like cylinder missing?

http://schematicsdiagram.blogspot.com/2012/01/while-stop-engine-idles-like-cylinder.html

---------

These details will help.

Thanks.

Feb 04, 2013 | Buick LeSabre Cars & Trucks

1 Answer

Does not idel well some time engin light comes on missies for 2 secomds


It can be issue with IAC( idle air control valve) causing the problem.


There are many other possibilities causing these idle issues. Engine idles rough.

There are few help links with solutions to troubleshoot such idle issues.

I suggest you refer the link below and follow its troubleshooting details:------

Click the link below:-----

Ford Expedition IAC valve replacing

http://technoanswers.blogspot.com/2012/12/ford-expedition-iac-valve-replacing.html

Bad miss at idle?

http://technoanswers.blogspot.com/2012/01/bad-miss-at-idle.html

-----------

Stumbling and stalling at idle after engine rebuild?

http://schematicsdiagram.blogspot.in/2012/03/stumbling-and-stalling-at-idle-after.html

------------

1999 Ford F-150 Idles rough and quits when gas pedal is pressed less?

http://technoanswers.blogspot.in/2012/01/1999-ford-f-150-idles-rough-and-quits.html

---------

Engine stumbles coming off idle when warm?

http://repairhelpcenter.blogspot.com/2012/01/engine-stumbles-coming-off-idle-when.html

------------------

Erratic idle on car?

http://schematicsdiagram.blogspot.com/2011/12/erratic-idle-on-car.html

-----------


Cold start problem and vehicle shudder around 2500 to 3500 rpms

http://repairhelpcenter.blogspot.com/2012/10/cold-start-problem-and-vehicle-shudder.html

----------

Low idle when cold out side?

http://repairhelpcenter.blogspot.com/2011/12/low-idle-when-cold-out-side.html

-----------

GMC Sonoma Stalls and idles low

http://technoanswers.blogspot.com/2012/10/gmc-sonoma-stalls-and-idles-low.html

--------


GMC Idle Air Control (IAC) Valve Replacing?

http://schematicsdiagram.blogspot.com/2011/12/gmc-idle-air-control-iac-valve.html

-------------

1996 Camry intermittent engine failure while idle?

http://repairhelpcenter.blogspot.com/2011/10/1996-camry-intermittent-engine-failure.html

------------

Engine quits at idle?

http://repairhelpcenter.blogspot.com/2011/10/engine-quits-at-idle.html

-----------

Car overheats and Air blows hot at idle?

http://howtobyme.blogspot.com/2011/11/car-overheats-and-air-blows-hot-at-idle.html

---------

High Idle Problem

http://repairhelpcenter.blogspot.com/2012/10/high-idle-problem.html

-------

While stop engine idles like cylinder missing?

http://schematicsdiagram.blogspot.com/2012/01/while-stop-engine-idles-like-cylinder.html

---------

Idle flair is noticed on car? Rough idle? car will not idle? Erratic idle speed?

http://technoanswers.blogspot.in/2012/02/idle-flair-is-noticed-on-car-rough-idle.html

--------

High rpm in neutral? Inconsistant high RPM in neutral?

http://technoanswers.blogspot.in/2012/02/high-rpm-in-neutral-inconsistant-high.html

-------

Vehicle stumbling at idle and shows code 54?

http://schematicsdiagram.blogspot.in/2012/03/vehicle-stumbling-at-idle-and-shows.html

----------

Rough idle, staling and Erratic shifting?

http://technoanswers.blogspot.in/2012/03/rough-idlestaling-and-erratic-shifting.html

-----------

While stop engine idles like cylinder missing?

http://schematicsdiagram.blogspot.com/2012/01/while-stop-engine-idles-like-cylinder.html

---------

These details will help.

Thanks.

Jan 08, 2013 | 2005 Mazda B3000 Cab

1 Answer

1993 1500 truck 5.0 high HC at idle


It can be issue with IAC( idle air control valve) causing the problem.


There are many other possibilities causing these idle issues. Engine idles rough.

There are few help links with solutions to troubleshoot such idle issues.

I suggest you refer the link below and follow its troubleshooting details:------

Click the link below:-----

Ford Expedition IAC valve replacing

http://technoanswers.blogspot.com/2012/12/ford-expedition-iac-valve-replacing.html

Bad miss at idle?

http://technoanswers.blogspot.com/2012/01/bad-miss-at-idle.html

-----------

Stumbling and stalling at idle after engine rebuild?

http://schematicsdiagram.blogspot.in/2012/03/stumbling-and-stalling-at-idle-after.html

------------

1999 Ford F-150 Idles rough and quits when gas pedal is pressed less?

http://technoanswers.blogspot.in/2012/01/1999-ford-f-150-idles-rough-and-quits.html

---------

Engine stumbles coming off idle when warm?

http://repairhelpcenter.blogspot.com/2012/01/engine-stumbles-coming-off-idle-when.html

------------------

Erratic idle on car?

http://schematicsdiagram.blogspot.com/2011/12/erratic-idle-on-car.html

-----------


Cold start problem and vehicle shudder around 2500 to 3500 rpms

http://repairhelpcenter.blogspot.com/2012/10/cold-start-problem-and-vehicle-shudder.html

----------

Low idle when cold out side?

http://repairhelpcenter.blogspot.com/2011/12/low-idle-when-cold-out-side.html

-----------

GMC Sonoma Stalls and idles low

http://technoanswers.blogspot.com/2012/10/gmc-sonoma-stalls-and-idles-low.html

--------


GMC Idle Air Control (IAC) Valve Replacing?

http://schematicsdiagram.blogspot.com/2011/12/gmc-idle-air-control-iac-valve.html

-------------

1996 Camry intermittent engine failure while idle?

http://repairhelpcenter.blogspot.com/2011/10/1996-camry-intermittent-engine-failure.html

------------

Engine quits at idle?

http://repairhelpcenter.blogspot.com/2011/10/engine-quits-at-idle.html

-----------

Car overheats and Air blows hot at idle?

http://howtobyme.blogspot.com/2011/11/car-overheats-and-air-blows-hot-at-idle.html

---------

High Idle Problem

http://repairhelpcenter.blogspot.com/2012/10/high-idle-problem.html

-------

While stop engine idles like cylinder missing?

http://schematicsdiagram.blogspot.com/2012/01/while-stop-engine-idles-like-cylinder.html

---------

Idle flair is noticed on car? Rough idle? car will not idle? Erratic idle speed?

http://technoanswers.blogspot.in/2012/02/idle-flair-is-noticed-on-car-rough-idle.html

--------

High rpm in neutral? Inconsistant high RPM in neutral?

http://technoanswers.blogspot.in/2012/02/high-rpm-in-neutral-inconsistant-high.html

-------

Vehicle stumbling at idle and shows code 54?

http://schematicsdiagram.blogspot.in/2012/03/vehicle-stumbling-at-idle-and-shows.html

----------

Rough idle, staling and Erratic shifting?

http://technoanswers.blogspot.in/2012/03/rough-idlestaling-and-erratic-shifting.html

-----------

While stop engine idles like cylinder missing?

http://schematicsdiagram.blogspot.com/2012/01/while-stop-engine-idles-like-cylinder.html

---------

These details will help.

Thanks.

Dec 06, 2012 | 1999 Chevrolet Silverado 1500

2 Answers

Misfire detected cylinder number 6


Hi there:
A P0302 and P0306 code means that the the car's computer has detected that one of the engine's cylinders is not firing properly. In this case it's cylinder #2 and #6.


Symptoms may include:
the engine may be harder to start
the engine may stumble / stumble, and/or hesitate
other symptoms may also be present


A code P0302 may mean that one or more of the following has happened:
Faulty spark plug or wire
Faulty coil (pack)
Faulty oxygen sensor(s)
Faulty fuel injector
Burned exhaust valve
Faulty catalytic converter(s)
Running out of fuel
Poor compression
Defective computer


Possible Solutions:
If there are no symptoms, the simplest thing to do is to reset the code and see if it comes back.

If there are symptoms such as the engine is stumbling or hesitating, check all wiring and connectors that lead to the cylinders (i.e. spark plugs). Depending on how long the ignition components have been in the car, it may be a good idea to replace them as part of your regular maintenance schedule. I would suggest spark plugs, spark plug wires, distributor cap, and rotor (if applicable). Otherwise, check the coils (a.k.a. coil packs). In some cases, the catalytic converter has gone bad. If you smell rotten eggs in the exhaust, your cat converter needs to be replaced. I've also heard in other cases the problems were faulty fuel injectors.


Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

May 05, 2012 | 1997 Ford Expedition

2 Answers

Stumble off idle


Stumble off idle,you have a misfire at idle the ignition system is of concern this will include plug wires sparkplugs cap and rotor,

Mar 03, 2012 | 1995 Dodge Dakota

1 Answer

Have a 2001 ford expedition with a 5.4 triton has a misfire in the number 3 cylinder i changed the spark plug and the coil pack on it confused on what it could be that keeps throwing these codes


Vehicles: Any vehicle with the above symptoms.

You have a bad spark plug wire on #3, or possibly a clogged/malfunctioning fuel injector on Cylinder #3. Or, less likely, some of the other possible culprits mentioned below (exhaust valve/O2 sensor/Catalytic converter/ECC).

I'm presuming the OBD-II DTC code from the Expedition's computer is P0303.
Always try resetting the code and see if it returns - your new spark plug and new coil pack may have fixed the problem, but if the P0303 code isn't reset, it'll remain stored,and the CEL (Check Engine Light) will remain lit.

If I were standing in front of the vehicle right now, the 1st thing I'd do is put my "mechanic's stethoscope" on the fuel injector with the motor running to verify correct operation. Why would I do this first? Its free, and informative. You'll hear both the explosion in the cylinder, and the "tic" sound of the fuel injector solenoid as the injector operates. Auscultate the properly functioning cylinders first, so you know what to listen for.

If all you have is a medical/Sprague-Rappaport stethoscope. remove the auscultation bell, and replace it with a 12-inch (36 cm) long wooden dowel or solid/hollow metal rod as a substitute. Sound will transmit just fine through the wood/metal. Prefer metal, if you have a choice.

Here's the "official" P0303 write-up:
------------------------------------------------------------------------------------------------------------
P0303 Code - Cylinder #3 Misfire
Technical Description

Cylinder #3 Misfire Detected

A P0303 code means that the the car's computer has detected that one of the engine's cylinders is not firing properly. In this case it's cylinder #3.
Symptoms
Symptoms may include:

the engine may be harder to start
the engine may stumble / stumble, and/or hesitate
other symptoms may also be present

Causes

A code P0303 may mean that one or more of the following has happened:

Faulty spark plug or wire
Faulty coil (pack)
Faulty oxygen sensor(s)
Faulty fuel injector
Burned exhaust valve
Faulty catalytic converter(s)
Running out of fuel
Poor compression
Defective computer (ECC)

Possible Solutions

If there are no symptoms, the simplest thing to do is to reset the code and see if it comes back.

If there are symptoms such as the engine is stumbling or hesitating, check all wiring and connectors that lead to the cylinders (i.e. spark plugs). Depending on how long the ignition components have been in the car, it may be a good idea to replace them as part of your regular maintenance schedule. I would suggest spark plugs, spark plug wires, distributor cap, and rotor (if applicable). Otherwise, check the coils (a.k.a. coil packs). In some cases, the catalytic converter has gone bad. If you smell rotten eggs in the exhaust, your cat converter needs to be replaced. In other cases the problems were faulty fuel injectors.

Dec 07, 2011 | 2001 Ford Expedition

2 Answers

Ford mercury cougar with the code p0301 whats dose this mean


A P0301 code means that the the car's computer has detected that one of the engine's cylinders is not firing properly. In this case it's cylinder #1.

Symptoms may include:
the engine may be harder to start
the engine may stumble / stumble, and/or hesitate
other symptoms may also be present

A code P0301 may mean that one or more of the following has happened:
Faulty spark plug or wire
Faulty coil (pack)
Faulty oxygen sensor(s)
Faulty fuel injector
Burned exhaust valve
Faulty catalytic converter(s)
Running out of fuel
Poor compression
Defective computer

Possible Solutions:
If there are no symptoms, the simplest thing to do is to reset the code and see if it comes back.

If there are symptoms such as the engine is stumbling or hesitating, check all wiring and connectors that lead to the cylinders (i.e. spark plugs). Depending on how long the ignition components have been in the car, it may be a good idea to replace them as part of your regular maintenance schedule. I would suggest spark plugs, spark plug wires, distributor cap, and rotor (if applicable). Otherwise, check the coils (a.k.a. coil packs). In some cases, the catalytic converter has gone bad. If you smell rotten eggs in the exhaust, your cat converter needs to be replaced. I've also heard in other cases the problems were faulty fuel injectors.

Hope helps.

Sep 14, 2011 | 1999 Mercury Cougar

2 Answers

I have code p0304 what does my 2001 ford focus need to fix?


Courtesy of obd-codes.com

Symptoms:
  • the engine may be harder to start
  • the engine may stumble / stumble, and/or hesitate
  • other symptoms may also be present
Possible Causes:

  • Faulty spark plug or wire
  • Faulty coil (pack)
  • Faulty oxygen sensor(s)
  • Faulty fuel injector
  • Burned exhaust valve
  • Faulty catalytic converter(s)
  • Running out of fuel
  • Poor compression
  • Defective computer

Jul 05, 2011 | 2001 Ford Focus

2 Answers

My 1998 ford exoedition check engine light is on and the code is cylinder 5 missfire


A P0305 code means that the the car's computer has detected that one of the engine's cylinders is not firing properly. In this case it's cylinder #5.

Symptoms may include:
* the engine may be harder to start
* the engine may stumble / stumble, and/or hesitate
* other symptoms may also be present

Causes: A code P0305 may mean that one or more of the following has happened:
* Faulty spark plug or wire
* Faulty coil (pack)
* Faulty oxygen sensor(s)
* Faulty fuel injector
* Burned exhaust valve
* Faulty catalytic converter(s)
* Running out of fuel
* Poor compression
* Defective computer

Possible Solutions:
* If there are no symptoms, the simplest thing to do is to reset the code and see if it comes back.

* If there are symptoms such as the engine is stumbling or hesitating, check all wiring and connectors that lead to the cylinders (i.e. spark plugs). Depending on how long the ignition components have been in the car, it may be a good idea to replace them as part of your regular maintenance schedule. I would suggest spark plugs, spark plug wires, distributor cap, and rotor (if applicable). Otherwise, check the coils (a.k.a. coil packs). In some cases, the catalytic converter has gone bad. If you smell rotten eggs in the exhaust, your cat converter needs to be replaced. I've also heard in other cases the problems were faulty fuel injectors.

Hope this helps.

Mar 17, 2011 | 1998 Ford Expedition

2 Answers

Having missfires at 4 an 6


A P0304 and/or P0306 code means that the the car's computer has detected that one of the engine's cylinders is not firing properly. In this case it's cylinder #4 and/or #6.

Symptoms may include:
* the engine may be harder to start
* the engine may stumble / stumble, and/or hesitate
* other symptoms may also be present

Causes: A code may mean that one or more of the following has happened:
* Faulty spark plug or wire
* Faulty coil (pack)
* Faulty oxygen sensor(s)
* Faulty fuel injector
* Burned exhaust valve
* Faulty catalytic converter(s)
* Running out of fuel
* Poor compression
* Defective computer

Possible Solutions:
* If there are no symptoms, the simplest thing to do is to reset the code and see if it comes back.
* If there are symptoms such as the engine is stumbling or hesitating, check all wiring and connectors that lead to the cylinders (i.e. spark plugs). Depending on how long the ignition components have been in the car, it may be a good idea to replace them as part of your regular maintenance schedule. I would suggest spark plugs, spark plug wires, distributor cap, and rotor (if applicable). Otherwise, check the coils (a.k.a. coil packs). In some cases, the catalytic converter has gone bad. If you smell rotten eggs in the exhaust, your cat converter needs to be replaced. I've also heard in other cases the problems were faulty fuel injectors.


Hope helps.

Feb 28, 2011 | 2000 Cadillac DeVille

Not finding what you are looking for?
2006 Ford Expedition Logo

154 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5530 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...