Question about 1994 Ford Crown Victoria

1 Answer

1994 Crown Victoria: need to add brake fluid to master cylinder...

Need to add brake fluid to master cylinder

Posted by Anonymous on

Ad

1 Answer

Why would you add fluid?
As the front pads wear,the fluid will go down, not an issue
If you keep opening the fluid resevoir,you will let moisture in.

Posted on May 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My brakes on my 96 crown victoria go all the way to the floor the brake fluid was empty and i filled it but it was empty again later that night what can it be?


Hi Joanne,first go to brake master cylinder and look for leaks,if none,then go to the inside of each tire and find bleeder screw ,look for leaks there,and if you have back drum brakes,then the wheel cylinders could be leaking and the leak is contained inside the drum and may not be seen till the drum comes off and it will cause the brake shoes to get hot and crystalize and crack.

Feb 04, 2013 | 1996 Ford Crown Victoria

1 Answer

The rear brake calipers on my 1992 Crown Victoria are sitting crooked on the roters. How can I fix it


The calipers are not bleeding back into the master cylinder. I suggest a flush with new fluid first, then bleed the system, starting first at the antilock, the the right rear, the left rear. This is a common problem when a complete brake job is not done.

Aug 29, 2012 | 1992 Ford Crown Victoria

2 Answers

Bleeding brakes on 1986 crown victoria


fill mastercylinder w/brake fluid,leave top off,then open all bleeders to all 4 wheels, leave open until u see fluid dripping,then make sure master cylinder is full of fluid,put lid back on, then close all bleeders. this is called gravity bleeding. warren madden

Dec 12, 2011 | 1986 Ford Crown Victoria

1 Answer

I think i need a master cylinder in my 1994 pontiac bnneville? How hard/easy it it to replace myself. I can purchase ne for around 50-60 dollars.


Yes it is not that hard to replace.

57435341
REMOVE OR DISCONNECT
  1. Retainer and electrical connector from fluid level sensor.
  2. Drain brake fluid front mister cylinder reservoir.
  3. Reservoir hose from master cylinder. Plug hose to prevent fluid loss and contamination.
  4. Brake pipes from master cylinder. Plug open pipes to prevent fluid loss and contamination.
  5. Two attaching nuts.
  6. Master cylinder.
  7. Reservoir, if it is to he used on replacement master cylinder.
INSTALL OR CONNECT
  1. Reservoir onto master cylinder, as needed.
  2. Master cylinder on to power booster.
  3. Attaching nuts. Tighten to 27 Nm (20 lb. ft.).
  4. Brake pipes. Tighten brake pipe fittings to 15 Nm (11 lb. ft.).
  5. Reservoir hose onto master cylinder.
  6. Fill master cylinder reservoir to full level mark using only Delco Supreme 11 Brake Fluid, or equivalent DOT 3 brake fluid.
  7. Electrical connector to fluid level sensor, secure with retainer.
  8. Bleed hydraulic system.
  9. Recheck fluid level in reservoir
113253687

Mar 09, 2011 | 1994 Pontiac Bonneville

2 Answers

Break peadle wont hold pressure


U are going to need a new brake master cylinder, the internal seals are leaking and allowing the fluid pressure to leak down, this why the sinking pedal

Jan 10, 2010 | 1994 Ford Crown Victoria

1 Answer

My transmission on my 94 crown victoria seems to


have the fluid changed, the new fluid should cure this.

Nov 02, 2009 | 1994 Ford Crown Victoria

1 Answer

1994 Ford Crown Victoria. There is a screeching & grinding coming from the right rear wheel. Only sometimes and when slowing down or starting from a stop. We have the wheel off and the rear end open....


wheel bearings??? and are you SURE the breaks are fine?? just because the shoes are not worn does NOT mean the master cylinder is working right there is alot to go wrong with rear breaks

Oct 28, 2009 | 1994 Ford Crown Victoria

1 Answer

Need to add brake fluid which reservoir do i add it to


Is normal because the brake pads/liners wear off ! As long you do not have a wet area by any wheel or at the master cylinder.

Aug 13, 2009 | 1994 Honda Accord

1 Answer

My car stop on me while driving. it also has a oil leak. The alarm comes on by itself.


have your rear wheel cylinders chesked for leaks when they leak brake fluid gets all over ur brake pads causeing them to lock up at random

Mar 30, 2009 | 1994 Ford Crown Victoria

Not finding what you are looking for?
1994 Ford Crown Victoria Logo

Related Topics:

217 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...