Question about 1999 Oldsmobile Intrigue

1 Answer

Wer can i find the crank sensors on a 99 olds intrigue 3.5 engine

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 104 Answers

The crank sensor is located below the front exhaust manifold and above the starter. To access it, you must lift the front of the vehicle, and remove the starter. Once the starter is removed the sensor is visible. Because of the poor location and poor GM engineering these sensors fail. You have excessive heat from the exhaust and oil leaking from the valve covers that short them out. Also once the sensor is replaced, it must undergo a re-learn process. Unfortunately this process can only be performed by a GM dealer via their computer system.....if you need further assistance, feel free to post them on FYa...hopefully this helps!!

Posted on May 05, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Evap port service


You'll need a repair book or shop manual to get the procedures.
Code 336 is for a problem with the crank sensor circuit, and 442 is for a small leak in the evap system. The leak could be the gas cap or a hose or valve between the gas tank and the vapor canister.

Apr 29, 2013 | 1999 Oldsmobile Intrigue

1 Answer

99 oldsmobile crank sensor 3800 where is it


The sensor is on the front of the engine just to the side crankshaft harmonic balancer.It is very hard to get at and requires special tools to replace it properly.

Sep 21, 2011 | 1999 Oldsmobile Intrigue

1 Answer

I have 99 olds intrigue. I've changedthe MAL


may sound strange but it could be your catalyic converter- air/exhaust has no where to go

May 10, 2011 | 1999 Oldsmobile Intrigue

1 Answer

What is symptom of a bad crank sensor. When I go up a hill my 99 intrigue sputters and breaks up bad. Also, when cruising steady engine fine, I accelerate and again it breaks up badly. What gives.


Usually when a crank sensor goes bad the car will not run at all, you can have an erratic reading that will cause your car to skip but will do it under any situation. Sounds like to me you have a problem with something in the
ignition system breaking down under a load. Could be a plug, wire, or coil.
depends on what engine you have. If it is a 3.8 liter the most common failure is the #1 spark plug wire, disconnect it and look at the ends, it they are corroded or look "rusty" you need to replace it. If so i would also replace the plug for that cylinder.

May 23, 2010 | 1999 Oldsmobile Intrigue

1 Answer

Crank sensor 1999 intrigue does it take special


Not on the 3.5l LX5. The crank sensor on that engine is near the starter.

Mar 03, 2010 | 1999 Oldsmobile Intrigue

2 Answers

Where is the crankshaft position sensor located on a 2000 intrigu


Should be located around 11:00 on front of engine at crank pully.

Oct 28, 2009 | 2000 Oldsmobile Intrigue

1 Answer

CLEANING THE MAF SENSOR ON MY '99 INTRIGUE


You don't clean them, you get a new one. Usually if it's the MAF, it'll start and die, start and die. If your's is stalling, it'll be the idle air control valve, or the fuel filter, or the idle control system, or a vacuum leak at the intake or vacuum hoses. Good luck.

May 06, 2009 | 1999 Oldsmobile Intrigue

1 Answer

Crank position sensor location


you will need to remove the starter to gain acess to the ckp sensor. once you remove the starter look on the engine block and you will see the sensor. The only problem with doing this repair yourself is that you will not be able to preform the crankshaft position variation learn procedure with out a factory scan tool. The vehicle may crank an run, but the timing advance curves will be wrong so the vehicle will probably cut off every time you remove your foot from the gas pedal. Hope this info helps!

Aug 18, 2008 | 2000 Oldsmobile Intrigue

Not finding what you are looking for?
1999 Oldsmobile Intrigue Logo

241 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...