Question about 2000 Ford Focus

1 Answer

Front wheel baring on ford focus

How do i replace the front wheel baring on a 2000 ford focus?

Posted by on

  • yadayada
    yadayada May 11, 2010

    baring?? bearing maybe?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 3,113 Answers

It has to be pressed in. Remove and try a machine shop.

Posted on May 09, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I get the rear drums off a 2000 Ford focus. I removed the spindle nut,


2000 Ford Focus Drum Removal ProcedureIf removing the drum to service the rear brakes: (note, do not remove hub retaining nut for this procedure)
1. Raise and support vehicle
2. Release the parking brake
3. Remove wheel and tire
4. Disconnect wheel speed sensor wiring harness from wheel knuckle and floor panel.
5. Remove 4 wheel spindle attaching bolts, then the wheel hub and drum assembly from vehicle.
6. Reverse procedure to install noting the following:
a. Torque wheel spindle retaining nut to 49 ft. lbs.
b. Torque wheel/tire assembly to 94 ft. lbs.
2000 Ford Focus Drum Replacement ProcedureIf replacing the drum and wheel bearing assembly:
1. Raise and support vehicle
2. Release the parking brake
3. Remove wheel and tire
4. Remove center dust cap.
5. Remove hub retaining nut.
6. Remove drum and hub assembly. Ensure wheel speed sensor ring is not damaged when removing drum/hub (if equipped).
7. Reverse procedure to install noting the following:
a. Inspect and clean wheel speed sensor ring if equipped.
b. When tightening hub retaining nut, rotate the hub assembly in counterclockwise direction.
c. Torque hub retaining nut to 173 ft. lbs.
d. Torque wheel/tire assembly to 94 ft. lbs.
e. Adjust parking brakes as necessary.


Jul 05, 2011 | 2000 Ford Focus

1 Answer

Ford focus 2000 squeaks front passenger side


sounds like a squealing belt or bad pulley on the engine.
If the brakes are indeed fine, then the solution is to work on the engine.
doubt if it's a wheel bearing, too.

Jul 10, 2010 | 2000 Ford Focus

1 Answer

How to replace front wheel bearings


Hello, the front wheel bearing is not to be serviced seperately, it comes as a complete unit with the front hub and the ABS sensor ring.

so there is no need to press the bearing into the hub.

Just remove the driveshafts, the rotors and calibers and replace the hub.

Jun 25, 2010 | 2000 Ford Focus

1 Answer

Ford focus' wheel bearings (2000 lx)


is difficult you need a press and some special tools as torquemeter to set the nuts to avoid the worn out of the new bearings.try to a local garage.buy the parts by yourself and the cost isnt so high!

Apr 13, 2010 | 2000 Ford Focus

1 Answer

I believe i have a clogged fuel filter on my 2000 ford focus


Your fuel filter is behind the drivers side wheel liner remove the drivers front wheel then remove the splash shield liner and you will see it mounted to the body of the car .

Jun 10, 2009 | 2000 Ford Focus

1 Answer

Air conditioner


The low pressure port is inside the right front wheel well on top of the dryer bottle, Turn your front wheels to the right and reach up behind the plastic guard just behind the front bumper

Jun 14, 2008 | 2000 Ford Focus

Not finding what you are looking for?
2000 Ford Focus Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5481 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...