Question about 2000 Volvo V40

1 Answer

Timing marks on a 2000 volvo v40 1.9t crank and cam marks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Volvo Master
  • 2,984 Answers

Timing belt alignment markings


timing marks on a 2000 volvo v40 1.9t - 9c6ff12.gif

Here is all the tech info for removing and replacing....hope this helps you:

4-Cylinder Engine

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Right hand engine cover
    • Cover over the right headlamp
    • Accessory drive belt
    • Front timing cover
    • Servo reservoir
  3. Position Volvo lifting beam 999 5006 or equivalent slightly in front of the front lifting eyelet for the engine. Use Volvo lifting arm 999 5383 or equivalent and Volvo lifting hook 999 5460 or equivalent to raise the front of the engine a few millimeters.
  4. Remove or disconnect the following:
    • Right-hand engine mount
    • Right front wheel
  5. Turn the crankshaft until the markings on the crankshaft and camshaft pulley correspond. Turn the crankshaft a further 1/4 turn clockwise and then back again until the markings correspond. The markings are illustrated. Remove the upper timing cover.
  6. Slacken off the center screw for the belt tensioner slightly.
  7. Turn the tensioner clockwise to 10 o'clock.
  8. Remove or disconnect the following:
    • Air baffles
    • Lower belt cover
    • Timing belt


To install:
  1. Turn all the pulleys listening for bearing noise. Check to see that the contact surfaces are clean and smooth. If the tensioner pulley lever or idler is seized, replace it.
  2. If replacing with a new idler pulley, tighten to 18 ft. lbs. (24 Nm).
  3. If replacing tension pulley, screw into place using the center bolt by hand. Ensure that the tensioner fork is centered over the cylinder block rib. Ensure that the Allen hole on the eccentric is at "10 o'clock".
  4. Install the timing belt in the following order:
    1. Around the crankshaft sprocket
    2. Around the idler pulley
    3. Around the camshaft sprockets
    4. Around the water pump
    5. Onto the belt tensioner
  5. Carefully turn the crankshaft clockwise until the timing belt is tensioned. The belt must be tensioned between the intake camshaft pulley, the idler pulley and the crankshaft
  6. Hold the belt tensioner center screw secure. Turn the belt tensioner eccentric counter-clockwise until the tensioner indicator passes the marked position.
  7. Then turn the eccentric back so that the indicator reaches the marked position in the center of the window and tighten the center bolt to 15 ft. lbs. (20 Nm).
  8. Press the belt to check that the indicator on the tensioner moves easily.
  9. Install or connect the following:
    • Lower belt guard
    • Air baffles
    • Upper timing cover
  10. Turn the crankshaft two turns. Check that the markings on the crankshaft and camshaft pulley correspond.
NOTE Check that the indicator on the belt tensioner is within the marked area.

  1. Install or connect the following:
    • Lower timing cover
    • Front timing cover and tighten to 9 ft. lbs. (12 Nm)
    • Accessory drive belt
    • Engine mount and tighten to 49 ft. lbs. (67 Nm)
    • Servo reservoir. Tighten bolts to 37 ft. lbs. (50 Nm).
    • Front wheel
    • Right hand engine cover
    • Cover over the right headlamp
    • Negative battery cable

Posted on May 04, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cam shaft and timing belt diagram 2008 Volvo S40 2.4


there are timing marke on the cam pulleys and crank shaft this is assuming that cams havnt been loosend

Jan 04, 2016 | 2008 Volvo S40 2.4

1 Answer

How do you line up the cam gear to the camshaft on a 1996 volvo 960


just align the cam and crank marks with the marks on the covers. the timing marks WILL NOT ALIGN with the number one piston on TDC. just align the marks and the car will run ok. that's the correct way to do it.

Aug 22, 2011 | 1996 Volvo 960

1 Answer

2000 volvo S70 timing


well timing on a volvo can some times a pain I would say start with ( with out looking at my self ) checking the timing belt or chain is not broken, by looking in side the oil fill cap at the cam shaft to see if it is moving. If the cam is moving it may have jumped time. you would need to reset the timing, also check your harmonic balencer for proper alingment to the crank shaft, and timing marks line up . look for timing mark alingment in your owner's manul.

hope this helps you if it dosen't please give me more information on your problem with the timing in detail.

Jan 02, 2011 | 2000 Volvo S70

1 Answer

I need cam timing settings for a volvo s40 2006


The timing marks on the cam gears align with the timing marks in the rear timing cover. The timing mark on the crank gear aligns with the timing mark on the oil pump assembly.
The tensioner is set by rotating the tensioner clockwise until the holes in the tabs on the left side of the tensioner are aligned, then tighten the center bolt.

Dec 24, 2010 | 2006 Volvo S40

1 Answer

Timing for a 1991 volvo 740


Hi, this is how to align timing on a 1991 Volvo 740.
There are marks for all three. Cam and Aux shafts have dots on face of outer gear. Cam lines up with mark on rear timing cover(about 1 o'clock). Aux lines up with mark on seal housing (about 3 o'clock) and crank lines up with mark on seal housing (about 12 o'clock).

Take care

Aug 08, 2010 | 1991 Volvo 740

1 Answer

I am installing a timing belt on a 1987 Volvo 240. I need to know how to time the Crank, cam and distributor. Thanks


camshaft pulley has a notch which lines up with notch on cam cover at approx 11o'clock, crankshaft marks also approx 11 o'clock and the aux shaft for distributer has marks at 9o'clock

Apr 24, 2010 | 1987 Volvo 240

1 Answer

While changing belt on volvo 960 1992 moved the camshafts how to sincronize agaein


First, your belt should have marks on it. they line up to the marks on the cam and the mark on the crank. If you don't have marks, check the old belt. If it has marks, transfer them to the new one. They are important and make the job 10 times easier. Your crank should be on tdc, on it's mark, and your cams also, on their marks. Once there, the cams can be clamped so they don't spring. If you have to move the engine, pull some spark plugs to take off the compression. Turn it over with a big socket on the crank shaft. Don't forget the pistons will hit the valves if they are not moving with the crank, so do the cams first, to get them out of the way, they only spring a little, 1/4 turn at the most. Get it lined up, get the belt lined up, pull the pin on the tensioner, you should be all set. Hope this helps.

Apr 15, 2010 | 1992 Volvo 960

2 Answers

1994 Volvo 940 Station Wagon timing belt


I hope you've solved the problem by now, but there are alignment marks on the crank shaft (top pulley), idler (lower side), and cam shaft (smaller, bottom pulley) which should be aligned with stationary marks on the timing belt rear cover.

The belt has marks that align with the aforementioned marks (lines). The double marks on the belt align with the camshaft marks and the single marks with the others.

Loosen the tensioner clamp (nut) to allow the spring loaded tensioner to press on the belt and retighten the nut.

Rotate the crank shaft (clockwise, probably two revolutions) and make sure the pulley marks realign to the marks on the cover (they don't have to realign with the marks on the belt).

Rotate the crank shaft a full revolution once the belt is on and check that alignment is preserved.

Periodically loosen and retension the tensioner nut (access through a hole in the cover) to ensure that tension is maintained as the belt relaxes.

Oct 25, 2008 | 1994 Volvo 940

4 Answers

Timing marks on volvo s40


the crank has the only mark you have a procedure for the cam gear you should see if the local dealer will print this out for you

Jul 01, 2008 | 2004 Volvo S40

Not finding what you are looking for?
2000 Volvo V40 Logo

4,115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...