Question about 1997 Chevrolet Camaro

1 Answer

I need help before i take a sledge hammer to my car. I just JB Welded the seam on my radiator and have a hole in the bottom now. I put some liquid glass to seal the hole for a few days until I can get my new radiator. In the meantime I changed the oil and filter and put in new fan relay fuses. My fans still don't come on and now the car won't start at all. I took the battery to autozone so I know the battery isnt the issue. Any ideas on what the problem is

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,309 Answers

Do the basics , spark, fuel pressure and injector tests, somewhere you will find the problem, the cooling fan comes on at approx 220 degrees, if not the sensor might be bad, you put in a sealer into the cooling system, on an older system it can plug up more that a leak, do not get discouraged my friend , just take it one step at a time

Posted on May 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change the studs on a 2003 Monte Carlo LS?


Wheel studs. . Thake hub or axel off car.
Using a hand held sledge hammer, drive out wheel studs toward the center of car, as if it we still on.
Install new wheel studs the same way bottoming them with the sledge hammer.

Jul 03, 2014 | 2003 Chevrolet Monte Carlo

1 Answer

How do you remove drivers side fender 1997 gmc sonoma


unbolt fender well leav hanging unlesss moven truck around 4 r 5 bolts under hood 1at bottom where door an fonder meet remove head lite(NOT ADJUSTMENT SCREWS) SHOULD B BOLTS B HIND LITE ON FENDER AN RADIATOR SUPPORT put new 1 on an line gaps up remanufactored fenders mite need 3lb sledge hammer an a block of wood. (only 4 remanufactord fenders0

Jul 12, 2012 | 1997 GMC Sonoma

2 Answers

I have a problem getting my rims off. I have chrome rims with key lug nuts. I left my car out in the weather for a year and now going to put back on the road but cannot get my lug nuts off. There was...


you can snap off the lugs and stems(worst case scenario). You plan on replacing rotors and calipers, so youll be in there anyway. I did this with my car and just replaced the stems and pressed them back in. If your going thru all this trouble to replace the other rusted parts u might as well change the stems. You really cant get liquid wrench in there. I used a socket a size too small, hammered on and wrenched off. Good luck

May 22, 2011 | 1993 Eagle Talon

1 Answer

Transmission fluid cool line running into the radiator has a pin hole leak.


I would drain the lines, put JB weld over the hole and all the way around so it won't blow off by the pressure after it's dry.
They also sell a JB weld underwater putty that work real good!

Or you could get a rubber hose and splice it and put over it and then use hose clamps on the spot on on the hole and then one for each end. Just about 3" of a piece will work

Jul 22, 2010 | 1992 Ford Taurus

3 Answers

1985 s-10


NO that Jb weld would fall off in less than a day. It get really hot and your best bet is to go to autozone and ask if they have a kit to replace holes on manifolds.

Aug 12, 2009 | 1985 Chevrolet S-10

2 Answers

Hole in radiator


You can try yourself with JB Weld or take to a Radiator Shop and have it Repaired.

Jan 21, 2009 | 2001 Nissan Altima

1 Answer

Put radiator stop leak didnt work. how hard to replace my self


you might not have to replace if you can find the leak u can use liquid steel or jb weld metal epoxy compound worked great for me

sometimes the radiator caps go bad also

Nov 29, 2008 | 2001 Jeep Cherokee

1 Answer

Get repair


You will need a bolt to fit into the small holes in the drum itself. then put them into the holes screw them in (2) needed and continue until it comes off. They are very stubborn sometimes. I have even had to use a mini sledge to hammer them off because of rust.

Sep 11, 2008 | 1990 Mazda MPV

Not finding what you are looking for?
1997 Chevrolet Camaro Logo

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

80339 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...