Question about 2006 Hyundai Sonata

1 Answer

2006 hyundai oil filter change

Where do i put the ring on the oil filter before i put the oil filter in so it doesnt leak oil.ive been putting the oil filter in but dont no where to put the rubber ring so i havent been using the ring.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 395 Answers

Well the ring should stay on the oil filter if there was one on there when you took off the old one it came off and dont need it

Posted on May 06, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi please can you help ive recently overhauled the the engine on my 2l opel rekord 1986 model but for some reason it keeps blowing the oil seal on the oil filter on start once then during idling once.


full rebuild with bearings, rings, head ,referb ,new oil pump
or partial rebuild re ring ?

filter issue wont be because of rebuild or higher oil pressure

try filling the filter with some oil before fitting
are you smearing the new oil filter seal with new oil before fitting
and is the surface of the face where the oil filter spins smooth no scratches or gouges or roughness

wierd
if the seal is intact you can use silicon sealant
to get it to seat and not leak

are to putting the filter on too tight or not tight enough?

spin till contact is made to block
and hand tighten only no filter tool
run motor and if leaking tighten one third turn more

if you use the tool and screw it on heavy
will flatten the seal and
you may need to cut the oil filter off next surface




26313277-eannglbp2b1gdiwnyfp3jmdj-5-0.jpg

26313277-eannglbp2b1gdiwnyfp3jmdj-5-1.jpg

26313277-eannglbp2b1gdiwnyfp3jmdj-5-3.jpg

Oct 16, 2016 | Opel Cars & Trucks

1 Answer

C240 w202 2000 oil leaking from filter, am i able to just put a new filter on without upsetting any sensors? As its quite a bad leak, think the o-ring might have loosen off maybe...


You can just put neew filter on. Slightly moisten the Oring with a smear of oil and tighten it up as much as you can. Remember to top up your oil at the same time, or take the opportunity to change it if it needs changing.
Good Luck

May 28, 2015 | 2000 Mercedes-Benz C-Class

1 Answer

Oil leak


is it leaking from top of filter -remove filter and check o-ring for damage and check housing for old o-ring[double gasket it happens] if good check housing for cracks and that gasket is good and bolts are tight -also check the pan gasket and bolts are good

Apr 30, 2013 | 2004 Chevrolet Blazer

1 Answer

Ford 3.8 blowing o ring on oil filter,what the heck is going on?


Sometimes when changing oil, the o ring comes off the old filter and stays in the groove. Then when putting new filter on, you end up with a double ring instead of one, this blowing out the seal.

May 02, 2012 | Cars & Trucks

3 Answers

Oil leak 2000 alero, just replaced plug, not it, leaked out all the oil after I drove it 20 miles, please help, could it be a gasket or what


Check the oil filter. The old gasket might be stuck on the engine (two gaskets stuck together), or the new gasket might be defective, misaligned or missing.

Nov 05, 2011 | 2000 Oldsmobile Alero

1 Answer

How to change the oil filter


Put the car on a lift or jacks. Since it has low clearnance you will need lower jacks or use a ramp.

Remove the oil cap and the oil filter. You may need a strap wrench if the oil filter is too tight to come off by hand.

Look for trap door under the metal cover underneath the car. Open the trap door and you will have access to the oil pan drain bolt.

Use 17mm socket to remove the drain bolt and catch oil into a basin.

Remove the oil filter from the oil cap housing. YOu will also have to remove a large and small oil ring as well as a washer. The new filter will come with those. The oil rings must go into the groove to prevent oil from leaking. The filter goes on the cap housing. The washer that comes with the oil filter goes with the drain plug. Take off the old washer drain plug and put on the new washer drain plug and drain bolt once all oil has poured out.

Ratchet in drain bolt and close the trap door. Put on oil filter by hand. Put in 7 quarts of 5w-30 oil. Check with the dipstick as you get to the last half quart.

Replace oil cap, start engine, and check for any indications of leaks.

Aug 25, 2010 | 2006 BMW 3 Series

1 Answer

My 2006 Sonata is leaking from the top of the oil filter, what


With more detail,I woild find a replacement at ur local salvage yard or buy a new one at ur local auto parts store,

Oct 01, 2009 | 2006 Hyundai Sonata

3 Answers

2006 hyundai sonata oil filter leak


I finally figured this out. I was putting the o-ring on incorrectly. I actually had two o-rings installed.
The o-ring should not be visible when it is tightened down. The plastic should be touching the metal housing. The o-ring sits inside the housing, right above the threads, but not at the top. Two pictures attached._388.jpg
_389.jpg

Dec 20, 2008 | 2006 Hyundai Sonata

1 Answer

Oil change


underneath the engine at the lowest point there is a bolt about 17mm undo drain oil then put 17mm plug in fill the new filter with new oil before screwing back on and place oil around rubber ring on new filter so it seals properly fill with oil to low point on dipstick start car check oil filter for leaks turn car off let oil settle and check level again too much oil in a motor will cause problems so dont over fill hope this helps glenn...........

Dec 15, 2008 | 2006 Suzuki Grand Vitara

Not finding what you are looking for?
2006 Hyundai Sonata Logo

Related Topics:

238 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...