Question about 1996 Toyota Corolla

1 Answer

Where is does the transaxle fluid go - 1996 Toyota Corolla

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Toyota Master
  • 76,630 Answers

On the transaxle case there is a pipe plug, it goes there.

Posted on May 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Transmission dipstick on xl7


what makes you think there is one,? not in the traditional sense, no.
read the operators guide yet?,
notice that page is missing, (trans checks) there is a DTC for this.
to tell you its time, that is covered in the FSM.

its missing for a good reason, on many newer cars.

AF33-5 trans box>?
fsm quote ( only an ecerpt, not COMPLETE< READ THE BOOK.
Important: Routine inspection of the transaxle fluid is not required. Transaxle fluid inspection is only required if there is a symptom indicating a concern with the fluid.
  1. Park the vehicle on a flat level surface.
  2. Operate the vehicle in order for the transmission fluid temperature to reach the normal operating range. Specification
    Transaxle normal temperature: 60-70 degrees C (140-158 degrees F)
  3. With the engine at idle, manual shift through all transaxle ranges and return to the PARK position. Leave the engine idling.
  4. Clean any dirt or debris away from the area of the transaxle fluid level indicator.
  5. Remove the transaxle fluid level indicator bolt (1) from the transaxle.
  6. Remove the transaxle fluid level indicator (2).
  7. Wipe away any transaxle fluid from the indicator.
  8. Insert the indicator into the transaxle until fully seated.
  9. Remove the indicator and inspect the level and the condition of the oil on the indicator:
    • Transmission fluid level at normal operating temperature (1)
    • Transmission fluid level if cold (2)
  10. If the fluid level is incorrect inspect for the following conditions:
    • Fluid below level, inspect for a leak.
    • Fluid above level, inspect for contamination of the fluid.
Important: The tranaxle uses T-IV fluid, GM P/N 88900925 (Canadian P/N 22689186). The fluid is normally red in color. The oil may darken in color with more miles on a vehicle.




f0e1632d-7bf2-41e0-97d8-e2600c1a72e1.jpg

Jun 24, 2014 | 2007 Suzuki XL-7

1 Answer

Where do i check trans fluid 1991 chevy cavalier


  • Fluid - M/T Dexron II Use a funnal add new fluid in the dipstick tube
  • HM-282 and 5TM40 Synchromesh Trans Fluid (Part No. 12345349)
  • GM-Isuzu 5 Speed Manual Transaxle Synchromesh Trans Fluid (Part No. 12345349)
  • Automatic Transaxle Fluid Level Checking Procedure
    VEHICLE APPLICATIONS:
    A, J, L, W Cars AND U-VAN
    BULLETIN COVERS:
    Transaxle fluid level checking and condition information. This updates all information previously published for 1990-93 HYDRA-MATIC 3T40, 4T60, 4T60-E and 4T80-E transaxles.
    Due to enhancement of assembly plant fluid fill capabilities, it is especially important to warm the transaxle up to operating temperature before determining that fluid needs to be added. If the transaxle fluid is close to operating temperature, the fluid level may read slightly below the "ADD" mark. DO NOT ADD FLUID UNLESS THE TRANSAXLE IS AT OPERATING TEMPERATURE AND THE DIPSTICK SHOWS FLUID LEVEL IS BELOW THE CROSSHATCHED AREA.
    TRANSAXLE FLUID LEVEL INFORMATION:
    Checking fluid level and condition (color and smell) at recommended service intervals will provide early diagnosis information about the transaxle. This information may then be used to correct a condition that, if not detected early, could result in major transaxle repairs.
    When adding or changing fluid, use only DEXRON(R)-IIE. Refer to Maintenance and Lubrication (Service Manual Section 0B) for maintenance information and service intervals.
    NOTICE: Do not overfill. Overfilling will cause foaming, loss of fluid, shift complaints and possible damage to the transaxle.Fluid level should only be checked when it reaches a normal operating temperature of 82-93 degrees C (180-200 degrees F). This temperature is reached after approximately 24 km (15 miles) of driving.
    TRANSAXLE FLUID COLOR:
    Fluid color will be red when new.
    IMPORTANT: When new, automatic transaxle fluid is red in color. The red dye is added so the assembly plant can identify it as transaxle fluid and distinguish # from engine oil or antifreeze. The red dye is not an indicator of fluid quality and is not permanent. As the vehicle is driven the fluid will begin to look darker in color. The color may eventually appear light brown. A dark brown color with a burnt odor may indicate fluid deterioration and signal a need for a transaxle fluid change.TRANSAXLE FLUID CHECKING PROCEDURE:
    1. Start engine and drive vehicle until the transaxle reaches operating temperature of 82-93 degrees C (180-200 degrees F). This temperature is reached after about 24 km (15 miles) of driving.Inaccurate fluid level readings will result if the fluid level is checked immediately after the vehicle has been operated under certain conditions:
    - When outside temperatures are above 32 degrees C (90 degrees F) - At sustained high speeds - In heavy city traffic during hot weather - Towing a trailer - In commercial service such as taxi or police use If the vehicle has been operated under any of these conditions, shut the engine off and allow the vehicle to cool for thirty (30) minutes. Then restart the vehicle and continue with step two. 2. Stop vehicle on level ground and put the gear selector in "P" (Park). 3. Set parking brake. 4. With your foot on the brake pedal, move the shift lever through each gear range, pausing for about three seconds in each range. Then put the gear selector back in "P" (Park). 5. Let the engine idle for three to five minutes. 41886034 6. Pull out the dipstick and wipe it with a clean rag or towel. 7. Push it back in all the way, wait three seconds and pull it back out. 8. Check both sides of the dipstick and read the lower level. The fluid should be in the crosshatched "HOT" area. IMPORTANT: The fluid level is ok if it is any where within the cross hatched area. It does not have to beat the top of the cross hatched area. Do not add fluid unless the fluid level is below the crosshatched area. 9. If the fluid level is where it should be, push the dipstick back in all the way. ADDING TRANSAXLE FLUID:
    If fluid level is low (after properly performing the checking procedure above) add only enough fluid to bring the level into the crosshatched area. It doesn't take much fluid, generally less than a pint. Don't overfill. Remember that the level does not need to be at the top of the crosshatched area to be correct.
    After adding fluid, always recheck the fluid level as described in the above procedure.

Apr 08, 2014 | 1991 Chevrolet Cavalier

1 Answer

03 saturn ion check and fill transmission fluid


IF YOU HAVE THE AF23-5 TRANSAXLE OR THE VT25- E VTI. TRANSAXLE YOU NEED A SCAN TOOL TO MONITORING TRANSMISSION FLUID TEMPERATURE WHILE CHECKING TRANSMISSION FLUID TEMPERATURE.YOUR VECHICLE TRANSAXLE DONT HAVE A DIP STICK TO CHECK TRANSMISSION FLUID LEVEL.YOUR TRANSMISSION HAS A DRAIN PLUG LOCATED BOTTOM OF TRANSAXLE BELOW FORWARD OF THE RIGHT PASSENGER SIDE DRIVEAXLE FACING RIGHT SIDE OF VECHICLE.YOUR VECHICLE HAS TO BE RAISED LEVEL ON A LIFT.TO CHECK TRANSMISSION FLUID.YOUR TRANSMISSION IS A DEALERSHIP FIX.WAY TRANSMISSION SET UP DEALERSHIP HAS TO CHANGE TRANSMISSION FLUID.

Nov 12, 2012 | Cars & Trucks

3 Answers

Just got 1996 chevy cavalier. Where do you add transmission fluid?


the transmission fluid goes down the dip stick hole ,either use a small funnel or special tranny fluid refill top up bottle

Feb 04, 2011 | 1996 Chevrolet Cavalier

1 Answer

How to check trasmission fluid no dipstick just a red cap


4T40E Automatic Transaxle CAUTION
Removal of the fluid level screw when the transaxle fluid is hot may cause injury. Use care to avoid contact of the transaxle fluid to exhaust pipe. The fluid level screw is intended to be used for diagnosing a transaxle fluid leak or resetting the transaxle fluid level after service that involves a loss of fluid.
  1. The fluid level should be checked when the transaxle is near room temperature or at 104°F (40°C). To acquire this, left the car idle for 3-5 minutes with all of the accessories off. Fig. 5: Location of the fluid level screw and the fill/vent cap needed to check the fluid for the 4T40E automatic transaxle 87951085.gif

  2. Apply the brake, then move the gear shift selector through all gear ranges, pausing three seconds in each range. Shift the lever into P.
  3. Raise and safely support the vehicle.
  4. Place a suitable drain pan under the check plug to catch any fluid that may drip out.
  5. Remove the oil check plug. The oil level should be at the bottom of the oil check hole. Because the transaxle operates correctly over a range of fluid levels, fluid may or may not drain out of the screw hole when the screw is removed.
  6. If fluid drains through the screw hole, the transaxle may have been overfilled. When fluid stops draining, then fluid level is correct and the check plug may be installed. If fluid does not drain through the screw hole, the transaxle fluid may have been low. Add fluid at the vent cap location in 1 pint increments until the oil level is at the bottom of the oil check hole.
  7. Install the oil check plug/fluid level screw and tighten to 10 ft. lbs. (14 Nm).
  8. Carefully lower the vehicle.
prev.gif next.gif

Jan 21, 2011 | 1997 Pontiac Sunfire

1 Answer

Need easy way to take off transmission fluid cap.Trying to check fluid.


Hello Eddie.

Checking the fluid level on these cars isn't easy. Not one of the Generals best ideas. There isn't a dipstick under that cap. The fluid level is checked by removing a screw on the side of the transmission while the car is running and sitting level.
This makes it tricky to do for the average do-it-yourselfer as you not only need to jack up the front of the car but the back end to keep it level. Probably a vain attempt to get the cars back into the dealers shop.

Anyway, here is the book procedure.

kiltylake_16.gif

kiltylake_17.gif


The fluid level screw is intended to be used for diagnosing a transaxle fluid leak or resetting the transaxle fluid level after service that involves a loss of fluid.

Inspect

The fluid level should be checked when the transaxle is near Room temperature or at 40°C (104°F) .

CAUTION: Removal of the fluid level screw when the transaxle fluid is hot may cause injury. Use care to avoid contact of transaxle fluid to exhaust pipe.

The engine must be running when the transaxle fluid level screw is removed, or excessive fluid loss will occur. Since the actual fluid level is unknown, stand clear when removing the fluid level screw. Have a container ready to capture any lost fluid.

WARNING: Do not turn the engine off with the fluid level screw removed as you can be injured by hot transaxle fluid being expelled out of the fluid check hole.

  1. Let vehicle idle for three to five minutes with accessories off.
  2. Apply brake
  3. Move shift lever through all gear ranges, pausing three seconds in each range.
  4. Place shift lever in Park. Important: Vehicle must be kept level on the hoist.
  5. Raise vehicle on hoist.
  6. Place oil container under fluid level screw.
  7. Remove the fluid level screw with the engine running at idle.
  8. Fluid level should be at the bottom of the fluid check hole. Because the transaxle operates correctly over a range of fluid levels, fluid may or may not drain out of the fluid check hole when the fluid level screw is removed. If fluid drains through the fluid check hole, this transaxle may have been overfilled. When fluid stops draining, the fluid level is correct and the fluid level screw may be installed. If fluid does not drain through the fluid check hole, the transaxle fluid level may be low. Proceed to ADDING TRANSAXLE FLUID.
  9. Install fluid level screw. Tighten 12 N.m (106 lb in)
  10. Lower vehicle.
  11. Shut off engine. Adding Transaxle Fluid: With the engine running, add fluid at the vent cap location in half liter (1 pint) increments until fluid drains through the fluid check hole. Allow the fluid to finish draining through the fluid check hole.
  1. Install fluid level screw. Tighten 12 N.m (106 lb in)
  2. Lower vehicle.
I hope this helps you along.
Thank you for using FixYa.

KL

Nov 19, 2010 | 2000 Pontiac Grand Am GT

1 Answer

Check automatic transmission fluid level 2004 Pontiac grand am


TRANSAXLE FLUID CHECKING PROCEDURE



The fluid level screw is intended to be used for diagnosing a transaxle fluid leak or resetting the transaxle fluid level after service that involves a loss of fluid.

Inspect
The fluid level should be checked when the transaxle is near Room temperature or at 40°C (104°F) .

CAUTION: Removal of the fluid level screw when the transaxle fluid is hot may cause injury. Use care to avoid contact of transaxle fluid to exhaust pipe.

The engine must be running when the transaxle fluid level screw is removed, or excessive fluid loss will occur. Since the actual fluid level is unknown, stand clear when removing the fluid level screw. Have a container ready to capture any lost fluid.

WARNING: Do not turn the engine off with the fluid level screw removed as you can be injured by hot transaxle fluid being expelled out of the fluid check hole.

  1. Let vehicle idle for three to five minutes with accessories off.
  2. Apply brake
  3. Move shift lever through all gear ranges, pausing three seconds in each range.
  4. Place shift lever in Park.
Important: Vehicle must be kept level on the hoist.

  1. Raise vehicle on hoist.
  2. Place oil container under fluid level screw.
  3. Remove the fluid level screw with the engine running at idle.
  4. Fluid level should be at the bottom of the fluid check hole. Because the transaxle operates correctly over a range of fluid levels, fluid may or may not drain out of the fluid check hole when the fluid level screw is removed. If fluid drains through the fluid check hole, this transaxle may have been overfilled. When fluid stops draining, the fluid level is correct and the fluid level screw may be installed. If fluid does not drain through the fluid check hole, the transaxle fluid level may be low. Proceed to ADDING TRANSAXLE FLUID.
  5. Install fluid level screw.
Tighten 12 Nm (106 lb. in.)

  1. Lower vehicle.
  2. Shut off engine.
Adding Transaxle Fluid:

With the engine running, add fluid at the vent cap location in half liter (1 pint) increments until fluid drains through the fluid check hole. Allow the fluid to finish draining through the fluid check hole.

  1. Install fluid level screw.
Tighten 12 Nm (106 lb. in.)

  1. Lower vehicle.

Oct 20, 2010 | 2004 Pontiac Grand Am

1 Answer

No tranny dipstick to be found ANYWHERE!!!!!!!!!


The fluid level screw is intended to be used for diagnosing a transaxle fluid leak or resetting the transaxle fluid level after service that involves a loss of fluid. Inspect The fluid level should be checked when the transaxle is near Room temperature or at 40°C (104°F) . CAUTION: Removal of the fluid level screw when the transaxle fluid is hot may cause injury. Use care to avoid contact of transaxle fluid to exhaust pipe. The engine must be running when the transaxle fluid level screw is removed, or excessive fluid loss will occur. Since the actual fluid level is unknown, stand clear when removing the fluid level screw. Have a container ready to capture any lost fluid. WARNING: Do not turn the engine off with the fluid level screw removed as you can be injured by hot transaxle fluid being expelled out of the fluid check hole. 1. Let vehicle idle for three to five minutes with accessories off. 2. Apply brake 3. Move shift lever through all gear ranges, pausing three seconds in each range. 4. Place shift lever in Park. Important: Vehicle must be kept level on the hoist. 5. Raise vehicle on hoist. 6. Place oil container under fluid level screw. 7. Remove the fluid level screw with the engine running at idle. 8. Fluid level should be at the bottom of the fluid check hole. Because the transaxle operates correctly over a range of fluid levels, fluid may or may not drain out of the fluid check hole when the fluid level screw is removed. If fluid drains through the fluid check hole, this transaxle may have been overfilled. When fluid stops draining, the fluid level is correct and the fluid level screw may be installed. If fluid does not drain through the fluid check hole, the transaxle fluid level may be low. Proceed to ADDING TRANSAXLE FLUID. 9. Install fluid level screw. Tighten 12 N.m (106 lb in) 10. Lower vehicle. 11. Shut off engine. Adding Transaxle Fluid: With the engine running, add fluid at the vent cap location in half liter (1 pint) increments until fluid drains through the fluid check hole. Allow the fluid to finish draining through the fluid check hole. 1. Install fluid level screw. Tighten 12 N.m (106 lb in) 2. Lower vehicle.

Jun 05, 2009 | 2004 Chevrolet Malibu

2 Answers

Location of transmission (automatic) dipstick


You DO NOT have one.

There is a small bolt/plug in the transmission above the pan that needs to be removed. The fluid will run out if it's overfilled. The transmission needs to be at room temperature or a little warmer to check the level.


The fluid level screw is intended to be used for diagnosing a transaxle fluid leak or resetting the transaxle fluid level after service that involves a loss of fluid.
Inspect:
The fluid level should be checked when the transaxle is near Room temperature or at 40°C (104°F).
CAUTION: Removal of the fluid level screw when the transaxle fluid is hot may cause injury. Use care to avoid contact of transaxle fluid to exhaust pipe.
The engine must be running when the transaxle fluid level screw is removed, or excessive fluid loss will occur. Since the actual fluid level is unknown, stand clear when removing the fluid level screw. Have a container ready to capture any lost fluid.
WARNING: Do not turn the engine off with the fluid level screw removed as you can be injured by hot transaxle fluid being expelled out of the fluid check hole.

  1. Let vehicle idle for three to five minutes with accessories off.
  2. Apply brake
  3. Move shift lever through all gear ranges, pausing three seconds in each range.
  4. Place shift lever in Park. Important: Vehicle must be kept level on the hoist.
  5. Raise vehicle on hoist.
  6. Place oil container under fluid level screw.
  7. Remove the fluid level screw with the engine running at idle.
  8. Fluid level should be at the bottom of the fluid check hole. Because the transaxle operates correctly over a range of fluid levels, fluid may or may not drain out of the fluid check hole when the fluid level screw is removed. If fluid drains through the fluid check hole, this transaxle may have been overfilled. When fluid stops draining, the fluid level is correct and the fluid level screw may be installed. If fluid does not drain through the fluid check hole, the transaxle fluid level may be low. Proceed to ADDING TRANSAXLE FLUID.
  9. Install fluid level screw. Tighten 12 N.m (106 lb in)
  10. Lower vehicle.
  11. Shut off engine.
181efc6.gif
Adding Transaxle Fluid:
  1. With the engine running, add fluid at the vent cap location in half liter (1 pint) increments until fluid drains through the fluid check hole. Allow the fluid to finish draining through the fluid check hole.
  2. Install fluid level screw. Tighten 12 N.m (106 lb in)
  3. Lower vehicle
0e45832.gif

Mar 23, 2009 | 1996 Chevrolet Cavalier

1 Answer

Transmission fluid


Transmission
fluid
Motorcraft SAE
75W-90 gear oil
(non-synthetic)
Manual transaxle 3.0 quarts
(2.87L)3
Motorcraft FNR5
Automatic
Transmission
Fluid
5–speed
automatic
transaxle
7 quarts (6.7L)4
Premium
Automatic
Transmission
Fluid
6–speed
automatic
transaxle
7.4 quarts
(7.0L

Oct 26, 2008 | 2006 Ford Fusion

Not finding what you are looking for?
1996 Toyota Corolla Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...