Question about 1991 Ford Ranger Supercab

1 Answer

Need to know which fuse is nuetral safety switch 1991 ranger 4 cyl 5 speed

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 721 Answers

There is none specifically for the switch.

Posted on May 04, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1991 Ford taurus starts when its cold then once it gets warm and you shut it off it wont start until it cools off again


Did you replace the ignition distributor stator? they are the real problem not the TFI ignition module. See part below. You must remove the distributor to replace this part, it would also be a good idea to run a fault code test on the EEC 4 engine control system.
4p1258-mvo5utiinxaozxzewv5notdb-4-0.jpg

Apr 20, 2017 | Ford Cars & Trucks

1 Answer

Where can I get a diagram to set the timing on a 1991 ford ranger?


First What type of engine is it 6 cyl /Petrol/Diesel/or V8 carb/type
or F.Inj , they are all differant.

Oct 05, 2014 | 1991 Ford Ranger Supercab

1 Answer

Need to know what 5 speed transmissions will interchange with a 92 ranger with a 3.0


You didn't mention if it was 2 or 4 wheel drive so I went with a 2 wheel drive. According to hollander the 5 speed transmaaion fits a ranger (2WD) 1991 - 1994 and a Mazda B3000 1994 only. Hope this helps.....

Oct 29, 2012 | 1992 Ford Ranger

1 Answer

Truck is a 4x4 and a 88 Ford Ranger, when you turn the key, the starter will not engage. However, if you ratchet the clitch, sometimes the starter turns over, Is it mechanical or the computer and does...


I know on mine (88 ranger 4x4 manual transfer case and ******, 2.9 v6, short wheel base) it has what seems to me to be something similar to a nuetral safety switch. The starter will not even try to engage unless the clutch is in. You're kind of vague in your description. But if your issue is not getting it to turn over when in nuetral, and not pressing in the clutch I don't think anything is broken, that it is a safety feature from Ford

Jul 06, 2011 | 1988 Ford Ranger

1 Answer

Try to start vehicle in park, new battery,alternator,serpentinebelt,dash signals come on,nothing. Try to start in neutral, ok. Try again inpark, nothing, then neutral, nothing? Park safty switch, or...


Try holding the key in the crcnk position while you slowly move the shift lever from park to nuetral and back to park. If at any point the vehicle tries to start while you are doing this than its the nuetral safety switch. From your description it sounds like the nuetral safety is the problem.

Dec 05, 2010 | 1991 Toyota Previa

1 Answer

Mustang 89 4 cyl 2.3 l engine starts on parking dies out on drive


if the nuetral safety was a problem the car would not start at all, sounds like you have a defective engine wiring harness, this is the most common cause of this i have seen while working for Ford.

Aug 27, 2009 | 2000 Ford Contour

1 Answer

1993 ranger 4 cyl.runs fine then wont restart for couple of hours


lisen for the fuel pump to run when it acts up. if u cant hear it then replace the fuel pump relay

Dec 21, 2008 | 1995 Ford Ranger Supercab

2 Answers

1991 ford ranger not getting any spark


probably the coil , but have your alternator checked first

Oct 07, 2008 | 1991 Ford Ranger Supercab

1 Answer

91 Ford Ranger 4 cyl 5 speed. Can`t find clutch slave cyl. bleeder. Internal slave. Hard at times to get into 1st and rev. Also can`t find connector to hook up tester for check engine light on.


first the bleeder will be located on the cylinder that is mounted on the transmission to engine connection by the bell housing. Second the port for this is located along the drivers side under the hood either by the fire wall or along the top of wheel well it will be marked with a grey cap labled EEC.

Aug 28, 2008 | 1991 Ford Ranger Supercab

Not finding what you are looking for?
1991 Ford Ranger Supercab Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...