Question about 1989 Toyota Corolla 2 Door

2 Answers

Accelerator needs pumping 3 times to start when cold engine low on power engine suffocates and jerks under full throttle, especially when cold sometimes emits a black smoke when being run hard.

Posted by on

  • Anonymous Mar 17, 2014

    engine emits alot of smoke on startup and white smoke while the vehicle is in motion, especially when the air condition is onwhen the vehicle accelerates it emits smoke

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 771 Answers

Does the engine have a tendency to stop when idling especially when you engage the power steering, brake or engage drive? If so this is classic IAC Idle Air Control valve trouble. The inlet and out let ports within the throttle body wall along with the the IAC could do with a real clean. Simply spray into the port opening some carb cleaner and leave to work for about five minutes. Clean out the gunky mess with a cloth. Wait 15 minutes for the cleaner residue to evaporate and restart your engine, you should notice an immediate difference

Posted on May 04, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 653 Answers

Yeah, you have a blaster, I means a leaky oil valve seal and when turning it of after driving you can rev the engine up a bit then immediately turn ignition off, this will leave enough fuel in fuel line when started the next day. Good?

Posted on May 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is code p0300?


P0300 - Random, Multiple Cylinder Misfire Detected Fault Code Definition
  • Random, Multiple Misfire Detected
Symptoms
  • Check Engine Light flashing
  • Rough running, hesitation, and/or jerking when accelerating
  • In some cases, there may be performance problems, such as dying at stop signs or rough idling, hesitation, misfires or lack of power (especially during acceleration), and a decrease in fuel economy
Common Problems That Trigger theP0300
  • Worn out spark plugs, ignition wires, coil(s), distributor cap and rotor (when applicable)
  • Incorrect ignition timing
  • Vacuum leak(s)
  • Low or weak fuel pressure
  • Improperly functioning EGR system
  • Defective Mass Air Flow Sensor
  • Defective Crankshaft and/or Camshaft Sensor
  • Defective Throttle Position Sensor
  • Mechanical engine problems (i.e.-low compression, leaking head gasket(s), or valve problems

Jul 25, 2014 | 2000 Dodge Durango

1 Answer

Jerking accelerating


This may be normal but you can adjust your driving to reduce the impact. To speed up the warm up process of the catalytic converters, the power train computer holds first gear a little longer than normal. This causes your car to get higher in the rpm range than normal, at part throttle, which causes the hard shift. On your first drive, try NOT to accelerate while the car is in first gear--it won't take long for you to learn how far this is.

Apr 22, 2014 | Mercedes-Benz E-Class Cars & Trucks

1 Answer

Engine starting problem.


run the fault codes
indicates an idle control sensor or other throttle / accelerator sensors

Nov 11, 2017 | 2005 Hyundai Tucson

1 Answer

I have a Land Rover freelander 2003, with V6 engine 2.5 liters. After starting the engine shakes and stalls or judders in low revolutions in neutral and when I accelerate. What I do is turned it of and...


first of course make sure the basics are ok and not in major need of a tune-up, after that check the throttle plate for excessive coking build-up, the computer is reliant on small amounts of air passing through to properly raise idle, usually this problem becomes prominent when your a/c pump comes one (which can even come on when using the heater or de-frost) especially when the car is cold( restarting the engine a couple of times can affect the engine temp, though probably unlikely) An injector cleaning has also been effective in elevating idle,but wont correct the problem in itself, as cleaning the throttle plate can.(check with vehicle maker for any precautions to take when cleaning throttle plate. I usually use carb-cleaner and a tooth brush. Also check for vacuum leaks and wiring harnesses. Listen for a fuel pump prime when key is turned to the on position(usually 2 or 3 seconds) this usually just causes extended cranking time though . check this stuff if all ok give me more info and I'll give you some tips on how to isolate your problem

May 24, 2010 | 2002 Land Rover Freelander

2 Answers

Rpm hunting


check for a vaccuum leak this is where i would start if it rolled into my shop. possibly a PCV valve sticking or a hole in the hose, this hose should run from the valve cover, or crank case and then to the intake, or carb.

Apr 25, 2010 | 1998 Isuzu Trooper

1 Answer

Ford Contour (2.5 V6 manual) jerks badly with throttle modulation


Check the lower motor mount near the drivers side. This usually is a problem with these cars. It costs about 140.00 or so depending where you reside. Also check the passenger side hanger bearing on the CV shaft if this is loose it will cause jerking too.

Jan 12, 2010 | 1998 Ford Contour

2 Answers

1997 F-350 Ford Powerstroke4x4 Crew Cab Diesel 83k miles. Truck runs fine while cold. When it starts reaching normal operating temp it starts missing and loosing power when accelerating. Truck idles fine....


Have you changed your oil? Rotella 15W-40. These engines really don't like old oil. It becomes too thick for the injection pump to work correctly. Another possibility is a bad cam sensor on the front of the motor. Most engines call this the crank sensor but on this engine you have to look it up as a cam sensor.

Sep 29, 2009 | Ford F-350 Cars & Trucks

2 Answers

Hesitation , skipping,engine cuts out when accelerating


Im having the same issue I believe. I have a 94\' Chevy 1500 and when i accelerate it will jerk like the gas has cut out but it wont stall. It just jerks and slows me down. It only seems to do it when going up a hill. I feel like it could be the fuel pump or possibly some intake gaskets?

Feb 28, 2009 | 1993 Chevrolet Lumina

Not finding what you are looking for?
Cars & Trucks Logo

151 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...