Question about GMC Yukon

1 Answer

My FOBs do not work on my 03 yukon. I have changed batteries, tried the reset - goes into reset mode but does not acknowledge reset.

Posted by on



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 15,935 Answers

Is this a factory alarm?


Posted on May 12, 2010

  • blueextc3221
    blueextc3221 Jun 03, 2010

    1. Close all vehicle doors.

    2. Insert the key into the ignition.

    3. Hold down the power UNLOCK button on the driver’s door panel-continue to hold
    down until instructed to release in step 9.

    4. Perform steps 5 through 8 in fairly rapid succession.

    5. Turn the ignition switch to the ON position (as far as you can go without starting the

    6. Turn the ignition switch to the OFF position.

    7. Turn the ignition switch to the ON position.

    8. Turn the ignition switch to the OFF position.

    9. Release the power unlock button on the door panel. The vehicle will lock and unlock
    the doors automatically.

    10. Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until
    the door locks and unlocks.
    This step may take up to 30 seconds.

    11. Repeat step 10 NOW for each additional transmitter (including any existing

    12. Turn the ignition switch to the ON position in order to exit the transmitter programming




1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Key fobs not working

Sounds like the batteries are weak I just had to change the batteries on mine and my wife's key fobs if you don't know how to change the batteries just go to you tube there should be a video on how to do that hope this helps

Oct 22, 2017 | Cars & Trucks

2 Answers

98 Oldsmobile Aurora There's a on my Dash it says information center and has the oil fuel speed all that it says low oil is there any way anybody knows how to reset that

Check your engine oil using the oil dipstick located on the engine - you need to add oil to the fill line as shown on the dipstick. You should have the oil replaced regularly (every 3-6 months) and keep your eye on the level if the engine is leaking oil underneath or burning a lot of it.

Mar 08, 2017 | Oldsmobile Cars & Trucks

1 Answer

Key fobs not working XK8 convertable

Try going through the set up of your key fobs like you replaced them and see if that works.

Apr 06, 2014 | 2004 Jaguar XK8

2 Answers

We have a 2003 yukon denali xl. we have a signal saying battery not charging. we replaced battery and alternator. still won't charge. truck goes completely dead. no lights, radio anything. what el

I'll try to help, everytime something gets replaced on these yukons, that circuit needs to be RESET ! Is there a reset button, on your steering wheel, to reset a variety of functions ? , check owners manual, or call your dealer for better advise

Feb 15, 2013 | 2007 GMC Yukon XL Denali

1 Answer

My original key fobs quit working on my 2005 GMC Yukon SLT. I changed the batteries with no positive result. I next replaced the key fobs and followed the programming. This worked for a couple of months...

The keyless entry system has the following main components:
• The transmitters
• The passenger door module (PDM)
The PDM communicates with the body control module (BCM) through the keyless entry serial data circuit. When you press a button on a transmitter, the transmitter sends a signal to the PDM. The PDM sends a request to the BCM and the BCM performs the appropriate function.

Jul 20, 2017 | 2005 GMC Yukon

1 Answer

2003Ford Explorer remote entry fobs booth stopped working yet batteries in them are good.

You can test the output of the Fobs at many Autoparts stores. They have one tester, usually on their counter and it usually has replacement batteries around it.

It sounds more like the receiver for the Keyless has shut down. But you may have a Menu problem on some cars. The Electronic dash Menu is where you can select the different features like "silent mode" door chimes, etc. Sometimes these get messed up when someone tries to reset the Oil change interval counter, then pushes the wrong button.

I hope my solution helps.

Oct 17, 2012 | Cars & Trucks

1 Answer

2003 GMC Yukon with new lock cylinder. Passlock won't relearn

un hook the battery cables then try to reset it if that dont work then you will need to take it to a shop to have the passlock code reset

Jan 22, 2010 | 2003 Chevrolet Tahoe

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts


Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides