Question about 2002 Kia Sedona

1 Answer

Oil Pump Sprocket and Chain Nois

My KIA Carnival Diesel TD 2.9L year 2000 is in engine repair, especially oil pump sprocket&chain and timing belt changes. KIA's technician said that " the sprokets and chain that will be used is harder than previous". What is the lifetime for these chain and sprockets?
Are these new chain&sprockets same with KIA Sedona?
Thanks

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 149 Answers

No and the life span should b btw 3 - 6 months

Posted on May 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I NEED TIMING CHAIN DIAGRAM FOR VQ20 NISSAN SERFIRO 1999


Instructions
  1. Remove Your Timing Chain
    • 1 Check your owner's manual for the recommended mileage for replacing your timing chain. Replacement for a Nissan Altima is 60,000 miles.
    • 2 Locate the timing chain. Replace it if the automatic chain adjuster (also known as the tensioner) is damaged or worn.
    • 3 Drain the cooling system and disengage the negative battery cable. Undo the spark plug wires and set the No. 1 piston at "Top Dead Center" (TDC) of the compression stroke.
    • 4 Disconnect the engine undercover, vacuum and fuel hoses, harness and connectors, drive belts, power steering reservoir, alternator and bracket, upper radiator hose, air duct, front exhaust tube, intake manifold collector supports, collector and exhaust manifold and the distributor.
    • 5 Prop up the oil pan and take out the front engine mounting, the valve cover, camshaft sprockets, cam bearing caps, camshafts, cylinder head bolts (reverse the installation order), cam sprocket cover, upper chain tensioner, chain guides and chain, idler sprocket bolt, cylinder head, intake manifold and cylinder head gasket and the steel oil pan.
    • 6 Place a steel cutter between the steel and aluminum oil pans. Slip the cutter around the oil pan's edge. Disengage the steel oil pan, baffle plate, oil strainer and the front tube.
    • 7 Secure the car on jack stands and place a seal cutter in between the oil pan and cylinder block. Slip the cutter around the oil pan's edge.
    Install Your Timing Chain
    • 8 Reconnect the crankshaft sprocket, oil pump drive spacer, idler sprocket and lower timing chain. Position the lower timing chain on the sprockets and line up the mating marks.
    • 9 Rub on an unbroken bead of liquid gasket and put in a new front cover and oil seal. Secure the bolt at 105 to 112 foot pounds (142 to 152 Nm).
    • 10 Eliminate any old material from the pan and cylinder block mounting surfaces. Rub on a 3.5 to 4.5mm bead of liquid gasket over the oil pan and cylinder block.
    • 11 Attach the upper timing chain to the idler sprockets and secure the cylinder head bolts.
    • 12 Refill the cooling system and add clean oil in the engine.
    • 13 Hook up the negative battery cable and any other disconnected parts or items. Start the engine and look for leaks.
Tips & Warnings
  • Procedures for replacing timing chains in Nissan Altimas vary slightly depending on engine size.
  • Make sure the new timing chain matches the chain you are removing.

Jun 12, 2012 | Cars & Trucks

2 Answers

Need timing gear marks for 2004 Kia Sadona 3.5L engine



Removal & Installation

3.5L Engine

  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Record the radio anti theft code data.
  3. Remove or disconnect the following:

    Negative battery cable Engine cover Accessory drive belts Idler pulley Crankshaft pulley Power steering pump pulley Belt tensioner pulley Upper and lower timing belt covers
  4. Support the engine with a floor jack and remove the engine mount.
  5. Rotate the engine to align the camshaft sprocket timing marks with the cylinder head cover timing marks.

    0996b43f8022cb71.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Timing belt routing and timing marks-3.5L Engine

  6. Remove or disconnect the following:

    Auto tensioner Timing belt

    0996b43f8022cb72.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Timing belt and related components-3.5L Engine


To install:
  1. Ensure that the engine is set to Top Dead Center (TDC).
  2. Prepare the auto tensioner for installation by compressing it in a vise and installing a retaining pin.
  3. Install the timing belt in the following order:
    1. Crankshaft sprocket
    2. Idler pulley
    3. Left bank exhaust camshaft sprocket
    4. Left bank intake camshaft sprocket
    5. Water pump pulley
    6. Right bank intake camshaft sprocket
    7. Right bank exhaust camshaft sprocket
    8. Tensioner pulley

  4. Install the auto tensioner. Do not remove the retaining pin at this time.
  5. Check that the crankshaft and camshaft timing marks are aligned correctly.
  6. Rotate the crankshaft 1 / 4 turn Counterclockwise .
  7. Rotate the crankshaft 1 / 4 turn Clockwise to return the engine to TDC.
  8. Loosen the tensioner pulley center bolt.
  9. Apply 44 inch lbs. (5 Nm) torque to the tensioner pulley as shown and tighten the center bolt to 32-41 ft. lbs. (43-55 Nm).

    0996b43f8022cb73.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Adjusting the tensioner pulley-3.5L Engine

  10. Remove the auto tensioner retaining pin.
  11. Rotate the crankshaft 2 revolutions Clockwise , then wait 5 minutes for the auto tensioner to adjust.
  12. Measure the auto tensioner rod as shown. If the measurement is not 3.8-4.5 mm, then repeat the belt tensioning procedure.

    0996b43f8022cb74.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Measuring the auto tensioner rod-3.5L Engine

  13. When the auto tensioner measurement is correct, install or connect the following:

    Engine mount Upper and lower timing belt covers Belt tensioner pulley Power steering pump pulley Crankshaft pulley Idler pulley Accessory drive belts Engine cover Negative battery cable
  14. Reprogram the radio anti theft codes.

    Kia_Sedona_2002-2006
    Timing Chain, Sprockets, Front Cover & Seal

    Print


    Removal & Installation

    3.8L Engine

    1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
    2. Record the radio anti theft code data.
    3. Remove the engine from the vehicle.
    4. Remove the drive belt. Remove the power steering pump. Remove the air conditioning compressor.
    5. Remove the alternator. Remove the drive belt idler. Remove the drive belt tensioner. Remove the water pump pulley. Remove the intake manifold.
    6. Remove the connector bracket from the left cylinder head cover. Disconnect the right ignition coil connector, condenser connector and remove the bracket.
    7. Remove the left cylinder head cover retaining bolts. Remove the cylinder head cover from the engine.
    8. Remove the right cylinder head cover retaining bolts. Remove the cylinder head cover from the engine.
    9. Set the No. 1 cylinder to TDC on the compression stroke. Turn the crankshaft pulley and align its groove with the timing mark T of the lower timing chain cover.
    10. Check that the mark of the camshaft timing sprockets are in straight line positioning on the cylinder head surface. If not rotate the crankshaft 360 degrees. Do not rotate the engine counterclockwise.
    11. Remove the oil pan. Remove the crankshaft damper pulley. Remove the timing chain cover.
      NOTE Be careful not to damage the contact surfaces of the cylinder block, cylinder head and timing chain cover. Before removing the timing chain, mark the right and left timing chains with an identification mark based on the location of the sprocket because the identification mark on the chain for TDC can be erased.
    12. After compressing the timing chain tensioner, install a set pin. Remove the right cam to cam guide. Remove the right timing chain auto tensioner and timing chain tensioner arm.
    13. Remove the oil pump chain cover. Remove the oil pump chain tensioner assembly. Remove the oil pump chain guide. Remove the right timing chain.
    14. Remove the right timing chain guide. Remove the oil pump chain sprocket and oil pump chain. Remove the crankshaft sprocket, oil pump and camshaft drive gear.
    15. Remove the left cam to cam guide. Remove the left timing chain auto tensioner and timing chain tensioner arm. Remove the left timing chain.
    16. Remove the left timing chain guide. Remove the crankshaft sprocket and left camshaft drive. Remove the tensioner adapter assembly.

      0996b43f8020193b.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing chain and related components-3.8L Engine


    To install:
    1. Check the camshaft and crankshaft sprockets for wear and damage, replace as required.
    2. Inspect the tensioner arm and chain guide for wear and damage, replace as required.
    3. Check that the tensioner pin moves smoothly when the ratchet pawl is released with a thin rod.
    4. The key of the crankshaft should be aligned with the timing mark of the timing chain cover. This indicates that the piston is at TDC on the compression stroke.
    5. Install the tensioner adapter assembly. Install the crankshaft sprocket and left camshaft drive.
    6. Install the left timing chain guide and torque the retaining bolts 14-18 ft. lbs.
    7. Install the left timing chain. Be sure to install the chain with no slack between the camshaft and the crankshaft (crankshaft sprocket, timing chain guide, exhaust camshaft sprocket, intake camshaft sprocket). The timing mark of each sprocket should be matched with the timing mark (color ink) of the timing chain at installation of the timing chain.

      0996b43f80201924.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Left timing chain markings and installation: (D) exhaust camshaft sprocket (C) intake camshaft sprocket-3.8L Engine

    8. Install the left timing chain tensioner arm and torque the retaining bolts 14-16 ft. lbs.
    9. Install the left timing chain tensioner and torque the retaining bolts 7-9 ft. lbs.
    10. Install the left cam to cam guide and torque the retaining bolts 7-9 ft. lbs.
    11. Install the crankshaft sprocket, oil pump and right camshaft drive.
    12. Install the oil pump chain and oil pump sprocket. Torque the retaining bolt to 14-16 ft. lbs.
    13. Install the right timing chain guide. Torque the retaining bolts to 14-18 ft. lbs.
    14. Install the right timing chain. Be sure to install the chain with no slack between the camshaft and the crankshaft (crankshaft sprocket, intake camshaft sprocket, exhaust camshaft sprocket). The timing mark of each sprocket should be matched with the timing mark (color ink) of the timing chain at installation of the timing chain.

      0996b43f80201925.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Right timing chain markings and installation: (C) exhaust camshaft sprocket (B) intake camshaft sprocket-3.8L Engine

    15. Install the right timing chain tensioner arm. Torque the retaining bolts to 14-17 ft. lbs.
    16. Install the right timing chain auto tensioner. Torque the retaining bolts to 7-9 ft. lbs.
    17. Install the right cam to cam guide and torque the retaining bolts to 7-9 ft. lbs.
    18. Install the oil pump chain guide. Torque the retaining bolts to 7-9 ft. lbs.
    19. Install the oil pump tensioner assembly. Torque the retaining bolts to 7-9 ft. lbs.
    20. Pull out the pins on both the left and right hydraulic tensioners. Install the oil pump chain cover.
    21. Rotate the crankshaft two revolutions in the clockwise direction. Confirm the timing mark. Be sure to rotate the crankshaft in the clockwise direction.
    22. Apply sealant on the chain cover and on the cylinder head, cylinder block, and lower oil pan. Be sure these parts are free of engine oil and dirt.
      NOTE Before assembling the timing chain cover, the liquid sealant TB1217H should be applied on the gap between the cylinder head and block. The part must be assembled with five minutes after the sealant is applied.


      0996b43f80201926.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Sealant application (1 inch bead width)-3.8L Engine

    23. Apply sealant on the chain cover.
      NOTE The liquid sealant TB1217H should be applied on the gap between the cylinder head and block. The part must be assembled with five minutes after the sealant is applied.


      0996b43f80201927.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing cover sealant application-3.8L Engine

    24. Install a new gasket to the timing case cover.
      NOTE It is important that the dowel pins on the cylinder block and holes on the timing chain cover should be used as a reference in order to assemble the timing chain cover in the correct position.


      0996b43f80201928.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing cover gasket installation (A) gaskets-3.8L Engine

    25. Install the timing chain cover. Torque the retaining bolts in the proper sequence and to specification. The engine should not be started for at least thirty minutes after timing chain cover assembly.

      0996b43f80201929.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing cover bolt torque sequence and specification-3.8L Engine

    26. Install the timing case cover oil seal.
    27. Continue the installation in the reverse order of the removal procedure.

May 19, 2012 | 2004 Kia Sedona

1 Answer

Timing chain 96 maxima broke


Check your owner's manual for the recommended mileage for replacing your timing chain. Replacement for a Nissan Maxima is 60,000 miles.2 Locate the timing chain. Replace it if the automatic chain adjuster (also known as the tensioner) is damaged or worn.3 Release the pressure in the fuel system, drain the cooling system and disengage the negative battery cable. 4 Undo the upper radiator hose, engine drive belts, power steering pulley and pump with bracket, air duct, passenger front wheel and engine side and undercovers, front exhaust pipe, cylinder head front mounting bracket and head cover, rocker cover, distributor and distributor cap and spark plugs.5 Take off the intake manifold support and move the No. 1 piston at "Top Dead Center" (TDC) of the compression stroke.6 Disconnect the cylinder head front cover, water pump pulley, thermostat housing, upper and lower tensioner and slack side timing chain guide, idler sprocket bolt, camshaft sprocket bolts, sprockets, mounting caps and camshafts. 7 Disengage the cylinder head with the manifolds, idler sprocket shaft, upper timing chain, center crossmember, oil pan and strainer assembly, crankshaft pulley, engine front mount and bracket and the front timing cover. Remove the oil seal and unfasten the timing chain cover, idler and crankshaft sprockets and the oil pump drive spacer. 8 Unfasten the timing chain guide. install Your Timing Chain 1 Grease the oil seal lip with engine oil and place it in the front cover. Verify that the No. 1 piston is at "Top Dead Center" (TDC) of the compression stroke. 2 Reconnect the crankshaft sprocket (marks should point toward the engine's front), oil pump drive spacer and timing chain guide and the lower timing chain. Line up all mating marks.3 Hook up the crankshaft sprocket and pulley, lower timing chain, front cover assembly, engine mount and front mounting bracket, oil strainer and pan assembly and center crossmember.4 Reattach the upper timing chain, idler sprocket (to the back side), cylinder head assembly, idler sprocket bolt and exhaust and intake camshafts. Place the intake camshaft knock pin at 9 o'clock and the exhaust pin at noon. Connect the camshaft bearing caps and distributor brackets and secure all mounting bolts.5 Eliminate any old material from the pan and cylinder block mounting surfaces. Rub on a 3.5 to 4.5mm bead of liquid gasket over the oil pan and cylinder block.6 Attach the upper timing chain to the idler sprockets and secure the cylinder head bolts.7 Refill the cooling system. Hook up the negative battery cable and any other disconnected items. Start the engine and look for leaks.

Oct 14, 2011 | 1996 Nissan Maxima

1 Answer

2001 ford ranger 4.0 engine timing chain replacement


Hi Josiah:
According with the repair guide...4.0L Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Negative battery cable Engine from the vehicle Oil pan Engine front cover Cylinder heads
  4. Lock the jackshaft tensioner by installing a pin.
    Jackshaft sprocket and chain assembly Left front cassette retaining bolt Cassette chain and tensioner assembly Rear jackshaft plug from the engine Right rear cassette retaining bolt and spacer Right rear cassette chain and tensioner Timing chain (s)

12_20_2011_4_41_36_pm.gif

Fig. Remove the jackshaft sprocket-4.0L SOHC Engine 2000-2001
Zooming link for Remove the jackshaft sprocket-4.0L SOHC Engine 2000-2001

To install:

  1. Install or connect the following:
    Timing chain(s) Right rear cassette chain, tensioner and sprocket Jackshaft sprocket and chain on the engine and remove the tensioner pin
  2. Torque the jackshaft sprocket bolt in 2 stages:
    1. 32-35 ft. lbs. (43-47 Nm).
    2. Turn an additional 65 degrees.
  3. Install or connect the following:
    Cylinder heads Front cover Oil pan Engine to the vehicle Negative battery cable
  4. Fill the engine with clean oil.
  5. Start the vehicle, check for leaks and repair if necessary.

  1. Before servicing the vehicle, refer to the Precautions section.
  2. With the vehicle in neutral, position it on a hoist.
  3. Remove the intake manifold.
  4. Remove the fuel supply manifold.
  5. Remove the accessory drive belt.
  6. Remove the thermostat housing.
  7. Remove the roller followers.
    NOTE You must retime the LH and RH camshafts when either camshaft is disturbed. Turn the crankshaft clockwise to position the number one cylinder at top dead center (TDC).

    NOTE The special tool must be installed on the damper and should contact the engine block to position the engine at TDC.
  8. Install the special tool.
    NOTE The right-hand camshaft sprocket bolt is a left-hand threaded bolt.
    NOTE If necessary, use camshaft gear torque adapter to loosen the camshaft sprocket bolt.


Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Aug 08, 2011 | 2001 Ford Ranger Regular Cab

1 Answer

I need timing marks on 2.2 toyota camry 2000


1. Remove the fan and generator V belt:
tdisline_542.jpg

tdisline_543.jpg 2. TIMING CHAIN (2az-FE Engine):
Before servicing the vehicle, refer to the Precautions Section.
Drain the engine oil.
Remove or disconnect the following:
Negative battery cable
Hood Right-side front wheel Engine under covers Right-side fender apron seal Front exhaust pipe Engine moving control rod and bracket Right-side engine mounting stay and bracket Accessory drive belt Engine appearance cover Engine wire Alternator Power steering pump, leave the hoses connected Ignition coils Ventilation hoses Cylinder head cover Turn the crankshaft pulley to set the No. 1 cylinder to TDC compression. Align the groove on the pulley with the timing mark -0- on the front cover. Remove the crankshaft pulley as follows:
1. TMC made: Use Special Tool 09213-54015 to hold the pulley to loosen the bolt. Use Special Tool 09950-50013 to remove the bolt and pulley.

2. TMMK made: Use Special Tool 09960-10010 to hold the pulley to remove the bolt. Use Special Tool 09950-40011 to remove the crankshaft pulley
tdisline_544.jpg Fig. Removing the crankshaft pulley-TMC-2.4L (2AZ-FE) engine
tdisline_545.jpg

Fig. Removing the crankshaft pulley-TMMK-2.4L (2AZ-FE) engine

Remove or disconnect the following:
Crankshaft position sensor Lower oil pan No. 1 chain tensioner Accessory drive belt tensioner

  • Support the engine with a suitable engine lifting device.
  • Remove or disconnect the following:
    Engine mounting insulators Right-side engine mounting bracket Stud bolt for the accessory drive belt tensioner from the block Front cover mounting bolts and nuts Front cover Crankshaft position sensor plate Timing chain tensioner slipper Timing chain vibration damper Timing chain Crankshaft timing sprocket
  • Turn the crankshaft counterclockwise by 90°, and align an adjusting hole of the oil pump driven sprocket with the groove of the oil pump.
    tdisline_546.jpg
  • Fig. Align the adjusting hole of the oil pump drive sprocket with the oil pump groove-2.4L (2AZ-FE) engine
    tdisline_551.jpg

    Fig. Insert a bar to lock the sprocket in position-2.4L (2AZ-FE) engine
    Put a bar in the adjusting hole of the oil pump driven sprocket to temporarily lock the sprocket in position. Remove the nut.

    Remove the bolt, chain tensioner and spring.

    Remove the chain tensioner, oil pump sprocket and No. 2 timing chain.

    To install:
    Set the crankshaft key into the left horizontal position. Turn the cutout of the drive shaft to the top

    tdisline_552.jpg

  • Fig. Align the crankshaft key and drive shaft cutout as shown for installation-2.4L (2AZ-FE) engine
    Align the yellow colored links with the timing marks of the sprocket as shown in the illustration.

  • Insert the sprockets with chain to the crankshaft and oil pump shaft.
  • Temporarily tighten the oil pump driven sprocket with the nut.
  • Insert the damper spring into the adjusting hole, and install the chain tensioner plate with the nut. Tighten to 9 ft. lbs. (12 Nm).
  • Align the adjusting hole of the oil pump driven sprocket with the groove of the oil pump.
  • Put a bar in the adjusting hole of the oil pump driven sprocket to temporarily lock the sprocket in position. Tighten the nut to 22 ft. lbs. (30 Nm).
  • Rotate the crankshaft counterclockwise by 90°, and align the crankshaft key to the top.
  • Install the timing chain vibration damper. Tighten to 80 inch lbs. (9 Nm).
  • Align the timing marks of the camshaft timing sprockets and bearing caps.
  • Using the crankshaft pulley bolt, turn the crankshaft and set the set key on the crankshaft upward.
  • Align the gold or orange colored link with the timing mark of the crankshaft timing sprocket.
  • Using Special Tool 09309-37010, tap in the sprocket.
  • Align the gold or yellow colored links with the timing marks of the camshaft timing gear and camshaft timing sprocket. Install the chain.
  • tdisline_553.jpg Fig. Align the marks of the sprockets and bearing caps to set the No. 1 cylinder at TDC-2.4L (2AZ-FE) engine
    tdisline_554.jpg Fig. Set the crankshaft set key facing upward-2.4L (2AZ-FE) engine
    tdisline_555.jpg Fig. Align the marked link of the timing chain with crankshaft sprocket timing mark-2.4L (2AZ-FE) engine
    tdisline_556.jpg Fig. Tap the crankshaft sprocket in with Special Tool 09309-37010-2.4L (2AZ-FE) engine
    tdisline_557.jpg Fig. Align the marked links of the timing chain with the camshaft sprockets during installation-2.4L (2AZ-FE) engine

    May 21, 2011 | Toyota Camry Cars & Trucks

    1 Answer

    How do u set timing on it? 1.8 engine


    Installation
    Install crankshaft sprocket on crankshaft.
    Make sure mating marks on crankshaft sprocket face front of engine.

    Position crankshaft so that No. 1 piston is at TDC and crankshaft key is at 12 o'clock.

    Install slack side timing chain guide and timing chain tension guide.

    Install timing chain on crankshaft sprocket.
    Set timing chain by aligning its mating mark with that on the crankshaft sprocket.
    Make sure sprocket's mating mark faces engine front.

    Install camshaft sprockets.
    Set timing chain by aligning mating marks with those of camshaft sprockets.

    Install camshaft sprocket bolts to correct torque.
    Apply new engine oil to bolt threads and seat surface.

    Install chain tensioner.
    Before installing chain tensioner, insert a suitable pin into pin hole of chain tensioner.
    After installing chain tensioner, remove the pin.
    Install timing chain guide.

    Install O-rings to cylinder block.

    Before installing front cover, remove all traces of RTV silicone sealant from mating surface using a scraper.
    Also remove traces of RTV silicone sealant from mating surface of cylinder block.

    Apply a continuous bead of Genuine RTV Silicone Sealant or equivalent to mating surface of front cover. Refer to RECOMMENDED CHEMICAL PRODUCTS AND SEALANTS .
    Check alignment of mating marks on chain and crankshaft sprocket.
    Align oil drive spacer with oil pump.
    Place timing chain to the side of chain guide. This prevents the chain from making contact with water seal area of front cover.

    Install front cover.

    Make sure two O-rings are present.

    Be careful not to damage oil seal when installing front cover.
    Install cylinder head bolts at engine front side as shown in Fig. 55.
    Tightening procedure:
    Tighten bolts (1 - 4): 6.3-8.3 N.m (0.64-0.85 kg.m, 55.8-73.5 in.lb).

    Install oil pump drive spacer.
    Install water pump and water pump pulley. Refer to REMOVAL AND INSTALLATION .
    Install idler pulley and bracket.

    Install RH engine mounting bracket

    Install RH engine mounting.
    Install oil pan. Refer to INSTALLATION.
    Install crankshaft pulley.
    Remove ring gear stopper.
    Install starter motor.
    Install cylinder head front cover.
    Apply RTV silicone sealant to cylinder head front cover.
    Use Genuine RTV Silicone Sealant or equivalent. Refer to RECOMMENDED CHEMICAL PRODUCTS AND SEALANTS .

    Install Camshaft Position Sensor (PHASE).

    Before installing rocker cover, apply a bead of Genuine RTV Silicone Sealant or equivalent, to mating surface of cylinder head as shown in .

    Install rocker cover gasket into rocker cover.
    Install rocker cover and tighten in numerical order as shown in
    Install spark plugs.
    Install ignition coils.
    Install front exhaust tube.
    Install front/right-side splash undercover.
    Install front RH wheel.
    Install drive belts.
    Adjusting drive belt deflection..

    Nov 29, 2010 | 2002 Nissan Sentra

    1 Answer

    How to set the timing on 1998 GMC Sierra 5.7


    5.0L and 5.7L Engines To Remove:
    1. Remove the crankshaft balancer.
    2. Drain the cooling system.
    3. Remove the water pump.
    4. Drain the engine oil.
    5. Remove all engine oil pan fasteners except two nuts at rear of engine.
    6. Separate the engine oil pan from the front cover.
    7. Disconnect the crankshaft position (CKP) sensor wire. gm-03-50-845.gif

    8. Remove engine front cover. gm-03-50-849.gif

    9. Pry the oil seal from the front cover.
    10. Inspect the front cover seal area and crankshaft balancer seal area for damage. gm-03-50-846.gif

    11. Rotate the crankshaft until the timing marks on the crankshaft and the camshaft sprockets are aligned.
    12. Remove the crankshaft position sensor reluctor ring. gm-03-50-847.gif

      NOTE: Free play on the slack side of the camshaft timing chain must measure less than 0.43 inch (11Mm) or timing chain and sprockets must be replaced.
    13. Remove the camshaft sprocket bolts.
    14. Remove the camshaft sprocket.
    15. Remove the camshaft timing chain. NOTE: Do not turn the crankshaft assembly after the timing chain has been removed in order to prevent damage to the piston assemblies or the valves.
      gm-03-50-848.gif

    16. Remove the crankshaft sprocket using J 5825-A.
    17. Remove the crankshaft balancer woodruff keys (if required).
    To Install:
    gm-03-50-850.gif

    1. Install the crankshaft balancer woodruff keys into the crankshaft.
    2. Align the crankshaft sprocket keyway with the crankshaft balancer woodruff key. WARNING
      Wear eye protection when installing crankshaft sprocket.
      gm-03-50-851.gif

    3. Use J 5590 to install crankshaft sprocket.
    4. Install the camshaft sprocket and camshaft timing chain. 9308kg61.gif

    5. Ensure that the crankshaft sprocket alignment mark is in the 12 o'clock position and the camshaft sprocket alignment mark is at the 6 o'clock position.
    6. Install the camshaft sprocket bolts and tighten the camshaft sprocket bolts;
      • Torque to: 18 ft. lbs. (25 Nm)
    7. Install the crankshaft position sensor reluctor ring until completely seated against crankshaft sprocket. NOTE: The composite type engine front cover and seal must not be reused. Always install a new engine cover with a new seal.
    8. Install new engine front cover and bolts.
      • Torque bolts to: 106 in. lbs. (12 Nm)
    9. Clean sealer from corners of oil pan gasket where it meets the engine front cover. gm-03-50-775.gif

    10. Apply a 0.196 in (5 mm) bead of adhesive, GM P/N 12346141 or equivalent, 1.0 in (25 mm) long to the engine front cover to engine block junction.
    11. Install oil pan bolts.
      • Torque bolts to: 106 in. lbs. (12 Nm)
    12. Tighten oil pan nuts.
      • Torque bolts to: 18 ft. lbs. (25 Nm)
    13. Connect the crankshaft position sensor wire.
    14. Install the water pump.
    15. Install the crankshaft balancer.
    16. Fill the engine to the proper level with oil.
    17. Fill the engine to the proper level with coolant.
    18. Test drive the vehicle to confirm the repairs.

    Nov 05, 2010 | GMC K1500 Cars & Trucks

    1 Answer

    How do i change the oil pump in a 2000 dodge intrepid


    I'm assuming that you are talking about 2.7L, the check this procedure...

    Removal & Installation - 2.7L Engines
    1. Drain the engine oil.
    2. Remove or disconnect the following:
      Crankshaft damper Timing chain cover Timing chain Crankshaft sprocket Oil pan Oil pickup tube and O-RING Oil pump

    To install:


    f24d78a.jpg

    Fig. Oil pump mounting bolt locations-2.7L engine

    1. Fill the oil pump rotor cavity with clean engine oil.
    2. Carefully, install the oil pump over the crankshaft and into position.
    3. Install the oil pump mounting bolts and torque to 21 ft. lbs. (28 Nm).
    4. Lubricate the new pickup tube O-ring with clean engine oil and torque the pickup tube mounting bolts to 21 ft. lbs. (28 Nm).
    5. Install or connect the following:
      Oil pan Crankshaft sprocket Timing chain Timing chain cover Crankshaft damper
    6. Fill the engine with clean engine oil.
    7. Start the vehicle, check for leaks and repair if necessary.

    Hope helps (remember to rate this).

    Oct 02, 2010 | 1999 Dodge Intrepid

    1 Answer

    Replacing the timing belt on a 1998 Nissan Quest and need to know cam shaft and crank shaft positions.


    go here for expert help on Villager & Quest

    http://groups.yahoo.com/group/villagerquest/

    e09cf57.gif

    Item Part Number Description 1 — 40 Timing Chain/Belt Teeth 2 6256 Camshaft Sprocket , Front 3 — 43 Timing Chain/Belt Teeth 4 6306 Crankshaft Sprocket 5 6268 Timing Chain/Belt 6 6256 Camshaft Sprocket , Rear
    Removal
    1. Drain the cooling system. Refer to Section 03-03 for the procedure.
    1. Disconnect the battery ground cable (14301) .
    1. Remove the generator drive belt, water pump and power steering pump drive belt, and the A/C compressor drive belt (if equipped). Refer to Section 03-05 for the removal procedure.
    1. If equipped, remove the three A/C compressor drive belt idler pulley bolts and the A/C compressor drive belt idler pulley.
    1. Remove the upper radiator hose bracket bolt.
    1. Loosen the two upper radiator hose clamps and remove the radiator hose bracket bolt. Remove the upper radiator hose (8260) and the upper radiator hose bracket from the vehicle.
    1. Remove the water bypass hose (8597) from between the thermostat housing and the water hose connection (8592) .
    1. Remove the main wiring harness from the upper engine front cover (6019) .
    1. Remove the eight upper engine front cover bolts and the upper engine front cover .
    1. Raise and support the vehicle.
    1. Remove the RH front wheel and tire assembly.
    1. Remove the four RH outer engine and transmission splash shield bolts and two screws and remove the RH outer engine and transmission splash shield (6775) .
    1. Use Strap Wrench 303-D055 (D85L-6000-A) or equivalent to hold the water pump pulley (8509) while removing the four water pump pulley bolts.
    1. Remove the water pump pulley from the water pump (8501) .
    1. Remove the crankshaft pulley (6312) . Refer to the procedure in this section.
    1. Remove the five lower engine front cover bolts and the lower engine front cover .
    2. Ensure that the timing marks between the crankshaft sprocket (6306) and the oil pump housing line up.
    3. NOTE: The directional arrow is necessary to ensure that the timing chain/belt (6268) can be reinstalled in the same direction.
    4. Loosen the timing chain/belt tensioner nut.
    5. Remove the timing chain/belt .

    6. Installation
      NOTE: Ensure that the timing marks on the camshaft sprockets (6256) and the seal plate are properly aligned. Ensure that the timing marks on the crankshaft sprocket and the oil pump housing are still aligned. NOTE: A new timing chain/belt has three white timing marks that indicate the correct timing positions of the camshafts (6250) and the crankshaft (6303) . These marks will help ensure that the engine (6007) is timed properly. When the engine is properly timed each white timing mark on the timing chain/belt will be aligned with the corresponding camshaft and crankshaft timing mark on the sprocket. Because the white timing marks are not evenly spaced you will need to refer to the following illustration for proper timing chain/belt placement. There should be 40 timing belt teeth between the timing marks of the front and rear camshaft sprockets and 43 teeth between the timing mark on the front camshaft sprocket and the timing mark on the crankshaft sprocket .

      NOTE: Verify that the camshaft timing marks are aligned with the timing marks on the seal plate, and that the crankshaft sprocket timing mark is aligned with the timing mark on the oil pump (6600) .

      Install the timing chain/belt starting at the crankshaft sprocket and moving around to the camshaft sprocket following a counterclockwise path. Do not allow any slack in the timing chain/belt between the timing sprockets. After all of the timing marks are matched up with the timing chain/belt installed, slip the timing chain/belt onto the timing chain/belt tensioner .





    Sep 20, 2009 | 1998 Nissan Quest

    1 Answer

    Serpentine belt


    5729dde.gif
    This is a job for an experienced technician. Probably about a $300 job. Maybe more.

    Here is procedure for 1996:

    Removal
    1. Drain the cooling system. Refer to Section 03-03 for the procedure.
    1. Disconnect the battery ground cable (14301).
    1. Remove the generator drive belt, water pump and power steering pump drive belt, and the A/C compressor drive belt (if equipped). Refer to Section 03-05 for the removal procedure.
    1. If equipped, remove the three A/C compressor drive belt idler pulley bolts and the A/C compressor drive belt idler pulley.
    1. Remove the upper radiator hose bracket bolt.
    1. Loosen the two upper radiator hose clamps and remove the radiator hose bracket bolt. Remove the upper radiator hose (8260) and the upper radiator hose bracket from the vehicle.
    1. Remove the water bypass hose (8597) from between the thermostat housing and the water hose connection (8592).
    1. Remove the main wiring harness from the upper engine front cover (6019).
    1. Remove the eight upper engine front cover bolts and the upper engine front cover.
    1. Raise and support the vehicle.
    1. Remove the RH front wheel and tire assembly.
    1. Remove the four RH outer engine and transmission splash shield bolts and two screws and remove the RH outer engine and transmission splash shield (6775).
    1. Use Strap Wrench D85L-6000-A or equivalent to hold the water pump pulley (8509) while removing the four water pump pulley bolts.
    1. Remove the water pump pulley from the water pump (8501).
    1. Remove the crankshaft pulley (6312). Refer to the procedure in this section.
    1. Remove the five lower engine front cover bolts and the lower engine front cover.
    2. Ensure that the timing marks between the crankshaft sprocket (6306) and the oil pump housing line up.
    2acab54.gif
    18. NOTE: The directional arrow is necessary to ensure that the timing chain/belt (6268) can be reinstalled in the same direction.

    If the timing chain/belt is to be reused, mark the direction of rotation on the timing chain/belt.

    19. Loosen the timing chain/belt tensioner nut.

    1. Remove the timing chain/belt.
    Installation
    NOTE: Ensure that the timing marks on the camshaft sprockets (6256) and the seal plate are properly aligned. Ensure that the timing marks on the crankshaft sprocket and the oil pump housing are still aligned.



    stv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Pay special attention to the tooth shape of the timing belt. The current timing belts are not interchangeable with the timing belts from the 1993 model year. The 1993 model year uses a square or trapezoidal tooth timing belt while the current model year uses a rounded tooth design. The design change was made to extend the service life of the timing belt from 60,000 miles for the square or trapezoidal toothed belt to 105,000 miles for the rounded tooth belt. If the proper timing belt is not used, the customer may complain of a "whining" noise coming from the engine compartment. If the camshaft sprocket has a square cut in the valley of the gear tooth, it will require a square or trapezoidal tooth timing belt. If the camshaft sprocket has a rounded cut in the valley of the gear tooth, it will require a rounded tooth timing belt.
    NOTE: If a new timing chain/belt is to be installed, make sure that the arrow is pointing away from the engine. If a timing chain/belt is to be reused, make sure that the directional arrow that was marked during disassembly is facing the correct direction.

    NOTE: A new timing chain/belt has three white timing marks that indicate the correct timing positions of the camshafts and the crankshaft. These marks will help ensure that the engine (6007) is timed properly. When the engine is properly timed each white timing mark on the timing chain/belt will be aligned with the corresponding camshaft and crankshaft timing mark on the sprocket. Because the white timing marks are not evenly spaced you will need to refer to the following illustration for proper timing chain/belt placement. There should be 40 timing belt teeth between the timing marks of the front and rear camshaft sprockets and 43 teeth between the timing mark on the front camshaft sprocket and the timing mark on the crankshaft sprocket.

    NOTE: Verify that the camshaft timing marks are aligned with the timing marks on the seal plate, and that the crankshaft sprocket timing mark is aligned with the timing mark on the oil pump (6600).

    Install the timing chain/belt starting at the crankshaft sprocket and moving around to the camshaft sprockets following a counterclockwise path. Do not allow any slack in the timing chain/belt between the timing sprockets. After all of the timing marks are matched up with the timing chain/belt installed, slip the timing chain/belt onto the timing chain/belt tensioner.

    1. While holding the timing chain/belt tensioner with an Allen wrench, loosen the timing chain/belt tensioner nut.
    1. Allow the timing chain/belt tensioner to put pressure on the timing chain/belt.
    1. Use an Allen wrench to turn the timing chain/belt tensioner 70-80 degrees clockwise and tighten the timing chain/belt tensioner nut to 43-58 Nm (32-43 lb-ft).

      1. Rotate the crankshaft (6303) clockwise twice and align the No. 1 piston to Top Dead Center (TDC) on its compression stroke.
      1. Apply 98N (22 lbs) of force on the timing chain/belt between the rear camshaft sprocket and the timing chain/belt tensioner.
      2. NOTE: An assistant may be needed to adjust the timing chain/belt.

        While holding the timing chain/belt tensioner steady with an Allen wrench, loosen the timing chain/belt tensioner nut. Remove the Allen wrench and adjust the timing chain/belt tensioner as follows:
        1. Install a 0.35mm (0.0138 inch) thick and 12.7mm (0.500 inch) wide feeler gauge as shown.

    1. Turn the crankshaft clockwise to position the feeler gauge between the timing chain/belt tensioner and the timing chain/belt

    1. Tighten the timing chain/belt tensioner nut to 43-58 Nm (32-43 lb-ft).
    1. Turn the crankshaft clockwise to remove the feeler gauge from between the timing chain/belt tensioner and the timing chain/belt.
    1. Rotate the crankshaft clockwise twice and align the No. 1 piston to TDC on its compression stroke.
    1. Apply 98N (22 lbs) of force on the timing chain/belt between the rear and front camshaft sprocket.
      1. Measure the timing chain/belt deflection. Timing chain/belt deflection should be between 13-15mm (0.51-0.59 inch). If timing chain/belt deflection is not within specification, repeat steps 3-11. If the timing chain/belt cannot be adjusted to within specification, the timing chain/belt will have to be replaced.
      1. Position the lower engine front cover and install the five lower engine front cover bolts. Tighten the five lower engine front cover bolts to 3-5 Nm (27-44 lb-in).
      1. Install the outer timing chain/belt guide and the crankshaft pulley. Refer to the procedure in this section.
      1. Position the water pump pulley on the water pump and install the four water pump pulley bolts
      1. Use Strap Wrench D85L-6000-A or equivalent to hold the water pump pulley, and tighten the four water pump pulley bolts to 16-21 Nm (12-15 lb-ft).
      1. Position the RH outer engine and transmission splash shield and install the four RH outer engine and transmission splash shield bolts and two screws.
      1. Install the RH front wheel and tire assembly. Tighten the lug nuts (1012) to 98-118 Nm (72-87 lb-ft).



    Feb 14, 2009 | 1993 Mercury Villager

    Not finding what you are looking for?
    2002 Kia Sedona Logo

    584 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Kia Experts

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    yadayada
    yadayada

    Level 3 Expert

    76109 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8269 Answers

    Are you a Kia Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...