Question about 2001 Ford Windstar

1 Answer

Does not move when put in gear. It starts and everything exept when put forwrd gear, it does not move

Posted by on

  • rooster123 May 11, 2010

    I have a lot of questions for you 1 does it move when put in reverse 2 Is the emergency brake set 3 was the emergency brake set If the answer is yes to the above you might try giving it power while in reverse. Sometime the e-brake is set in wet weather and the metal fibers in the brake pad will rust/weld themselves it the drums/rotors and they will break loose while moving in reverse where they might not allow it to move forward at all. If that help great otherwise I would need a bit more info

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Do you have a bad axle shaft? It can turn the inner axle inside the joint and not move the car as if the trans is bad.

Posted on May 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Powerseat switch does not work on 1993 bonnivillehow to manually move seat or jump switch out


Get another switch from a junk yard. the seat will not move manually. If you're going to try to jump the switch it's easier to just replace it.

Dec 23, 2012 | 1993 Pontiac Bonneville

1 Answer

My 03 Windstar will not move in any gear


Have you checked the transmission fluid?

Sep 27, 2012 | 2003 Ford Windstar

1 Answer

I bought a tired 1994 gmc jimmy with a 4.3 vortec motor with 243,000 miles on it and just want to get more driving out of it. it is also 4wheel drive 1 problem i ,m having is that the oil pressure reads 40...


Do you have the electric shift 4wd? If so, start by checking if there is power to the actuator on the transfer case.

ok you hear a noise in the dash and a noise under the truck. there will be two noises under the truck one puts the transfer case into gear the other locks the fromt axle. raise rear axle let truck idle in 4x4 look under truck is front shaft moveing if yes the 4x4 motor on the front axle is not working remove dissasemble clean lube reinstall. if the shaft does not turn do this same procedure on the elec motor on trans case..good luck you can replace your oil pump it may help vehicle
Looking at the motor from the front, it is behind carb and to the right of the distributor. It has 3 wires on it.


Dec 12, 2010 | 1994 GMC Jimmy

1 Answer

96 caravan 3.0 , have had it two weeks now bought from a cousin who had trans rebuilt. Test drove it, everything was fine. seems the trans was starting to require a little gas to move but after you got it...


If it happens in all gears then the out put shaft is worn. If it only happens in reverse then find out from your cousin where he had it repaired from .It might be still under warranty. If not take it to a tranny repair shop sounds like oil pump in converter may be weak 0r reverse gear or its idler is worn.

Sep 15, 2010 | Dodge Caravan Cars & Trucks

1 Answer

Need tha diagram for a 2.4 dodge stratus timing marks


timing mark?everybody asks me the same question.First everything is removed and cleaned and i mean very clean?always start at the top ,on the gear you will find a dot/indent,on the plate/casing behind the gear you will also find a dot/indent line the two up and dont move ,do the same with all the other gears and dont move them [water pump dosent matter it does not need timing]once you are satisifed get the NEW belt and slowly put it in and remember what i told you at the start do not move the gears that are lined up not even a tooth. once belt is in position with all dots lined release tention pully and ther there you go you have timed your engine well done.adrian,,,,,,,,,

Aug 16, 2010 | Dodge Stratus Cars & Trucks

1 Answer

I HAVE A 1996 DODGE RAM 1500 I CHANGED TRANSMISSION AND ALL I GOT IS FORWRD GEARS IN ALL GEARS COULD IT BE THE BANDS


Sounds like the valve body is stuck,try a product called lube guard,at napa auto parts,it will unstick the valve body.

Jan 30, 2010 | 1996 Dodge Ram 1500 Club Cab

Not finding what you are looking for?
2001 Ford Windstar Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...