Question about Ford Crown Victoria

1 Answer

What causes hesitation on a 1988 ford crown victoria so far i replaced wires, plugs, air filter, distributor cap

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 6,826 Answers

Check for the vacuum tee in the rear to have a hole in it,it may even be sucked together,and it could be the throttle position sensor.

Posted on May 04, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My crown vic turning over but wont crank never did this before


The most likely cause is a bad ignition coil, remove the coil wire from the distributor and attach an old spark plug to it, have a helper crank the engine, and see if the spark plug fires. If the plug does not fire then the coil is bad. If the plug fires, remove a plug wire from a spark plug and repeat the process. If no spark then the distributor cap may be bad? Also have you ruled out no gas???

Jan 11, 2015 | 1992 Ford Crown Victoria

1 Answer

I cleaned my engine on my 2000 ford crown victoria. Now it hesitates. Why?


Usually when you clean your motor always cover up the distributer cap area where the wires are, or were they plug in engine could of gotten some water usually takes little bit to dry out and then your back to normal, other suggestion is to blow the engine with air hose good luck

Jul 23, 2011 | 2000 Ford Crown Victoria

1 Answer

I have a 1988 berretta gt it just started stalling at lights eng light some times comes on when this happens but goes off soon after. the car starts back up fine can you help.i tryed map sen. tpo sen and a...


Hi,
Does it lack power and hesitate sometimes? Have you replaced plugs,wires,distributor cap and rotor anytime in the past? Has the catalytic converter been replaced anytime in the past? Fuel filter? Air filter? Check for leaks at vaccuum lines? Repost with answers, we can see if we can determine a possible cause other than those and what you have stated you replaced already. thanks, Mike

Jun 14, 2011 | 1988 Chevrolet Beretta

1 Answer

WHAT NEEDS TO BE DONE TO TUNE UP A 2003 FORD CROWN VICTORIA


spark plugs, wires, fuel filter and air filter and oil change

Mar 05, 2011 | 2003 Ford Crown Victoria

1 Answer

Hesitation on take off and a miss while goin down the road in my 1994 2.3l ford ranger


Start with a complete tune-up

Plug wires can cause this.

Do spark plugs, spark plug wires, distributor cap, rotor cap, spark plug wires, fuel filter, air filter, oil & oil filter.

People often neglect these simple things which could save your motor, maintain it's efficiency plus improve gas mileage.

Feb 20, 2011 | 1994 Ford Ranger Supercab

2 Answers

I have a 1996 crown vic i need to know these touble codes po305 po304


P0304 means that cylinder 4 has a misfire and P0305 is a cylinder 5 misfire. What this means is you may have bad spark plugs, or bad plug wires, or you may need to replace your distributor cap and rotor. I would start with plugs and wires.

Oct 21, 2010 | 1996 Ford Crown Victoria

1 Answer

How do you tune up a 1993 ford crown victoria


All you really have is the spark plugs and spark plug wires, I believe your car doesn't have a cap and rotor to replace, just coil packs, which really isn't something you replace when you do a tune up. I would also replace the fuel filter and check the air filter. Make sure you change 1 wire at a time, so they don't get put back on wrong.

May 06, 2010 | 1993 Ford Crown Victoria

1 Answer

Engine does not start immediately when cranking


The problem could be many things. Is the engine light on? Check for proper fuel pressure. Remove one spark plug and inspect. Your vehicle may just need a simple tune up. Spark plugs,distributor cap and rotor,fuel filter.

Jul 26, 2009 | 1991 Ford LTD Crown Victoria

2 Answers

Horrible Idle, Then Engine stalls


Sounds like the copper seal that the old owner put in quit working.

a lemon is still a lemon no matter how sour.

Jul 07, 2009 | 1988 Ford Crown Victoria

1 Answer

1988 Ford Crown Vic Strange Idle (Getting Worse)


i am trying to install an aftermarket temperature guage with capillary tube into my 1988 crown victoria ltd 5.0 efi. where does the capillary tube mount?

Jun 27, 2009 | 1988 Ford Crown Victoria

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

109 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...