Question about Buick Rendezvous

2 Answers

My 3rd row window got broken. So how do i remove 1 from another car and install it to my car? Also where can i buy a new 1? 2002 buick rendezvous

Posted by on

  • cody314 May 04, 2010

    no i need to no how on the quater panel window/ 3rd side window?

  • cody314 May 04, 2010

    if i cut the seal how will i re use it?

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,427 Answers

Ok to remove

  • open out door by removing upholestry
  • have a friend claps the glass between both palms to hold it up..
  • you will notice some bolts on door hidden by upholestry
  • remove bolts
  • this releases the ARm, guide and regulator as well as power motor..
  • let glass down half way then remove at angle
to install

1 insert glass indoor ensureing its set in the gudies to the sides
  1. bolt up arm and motor then botl glass to arm
thats it your done..

Posted on May 04, 2010

  • 1 more comment 
  • Rishi Roshan Ali May 04, 2010

    oh that...



    • get a knife.. cut away the ribbol seal that holds it in place

    • carefully pry it loose..


  • Rishi Roshan Ali May 04, 2010

    u buy new ones,, as well as a tube of ribbon sealer



  • Rishi Roshan Ali May 04, 2010

    if u want you can try pulling the rubber off without breaking it or cutting it.. its hard but possible..

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Buick Master
  • 1,851 Answers

Hi,,
I think you may want a professional to do this but here is something to help you if you decide to do it yourself. Please watch both videos before deciding.

Posted on May 04, 2010

  • Gary Rice
    Gary Rice May 04, 2010

    I see - To replace a side window is exactly like a windshield or rear window. the cosmetic edge also keeps the window glass in place. There are special tools that allow you to remove the trim - then the rubber molded seal. The seal also anchors the glass into place.
    The best way is found here.
    http://www.youtube.com/watch?v=5nCm0vQab...
    Thanks





  • Gary Rice
    Gary Rice May 07, 2010

    The window comes out just like the windshield -
    1 - remove retainer band or rubber seal - there are specialty tools you must purchase to do this unless the window is broken. If the window isn't broken - try using the correct tools this avoids a broken seal - then use silicone to seal the seal and window - this is really a job for the pros because these windows are brittle and will break with the slightest pressure the wrong way.


×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Were is the fuse for the windows


2 IN THE FUSE BOX UNDER THE HOOD. LOOK AT IT WITH THE RELAYS ON TOP, FIRST ROW OF MINI FUSES 3RD OVER 30 AMP. NEXT ROW 4TH OVER 30 AMP!! IN THE CAR THE BOTTOM RIGHT FUSE 30 AMP!!

Nov 17, 2013 | 2002 Lincoln Continental

1 Answer

I have a 2002 Buick rendezvous I keep having problems with it locking up to wear my car will not start what could be causing this is it my security system locking up or what please help


Not sure if you mean engine is locking or vehicle will not crank. If the vehicle doesnt crank and the security light is flashing, the problem is most likely a worn out key and lock and tumbler assembly. Once replaced the new key will have to be recognized by the body control module through a reset procedure. Close drivers door. Turn ignition to run position and wait for security light to go out. Turn key off for 2 seconds. Do this 3 times in row. After turning key off 3rd time the key code should be recognized by the body control module and the vehicle should start. Hope this helps.

Mar 25, 2012 | 2002 Buick Rendezvous

1 Answer

I need to know how to fix the power windows in my 91 buick


check the fuse that protects the power windows, it's fuse l, last from 3rd row

Mar 15, 2010 | 1991 Buick Regal

2 Answers

1999 ford expedition


1999 Expedition

Seats — Third Row
The third row seat is:
  • a three-passenger seat.
  • engaged to the floor by a latch and striker assembly.
  • a quick release seat.
  • equipped with rollers to ease removal and installation.

Dec 17, 2009 | 2002 Ford Expedition

1 Answer

How do you remove the 3rd row seat on a 2002 ford expedition


remove seat to floor mounting bolts, then detach the seat and lift out of vehicle. install in reverse

Oct 15, 2009 | 2002 Ford Expedition

1 Answer

Cant release spare tire from under car of 2002 mercury villager. no owners manual available.


Location of the spare tire and tools
The spare tire and tools for your vehicle are stowed in the following
locations:
Item Location
Spare tire Under the vehicle, just forward of
the rear bumper
Jack assembly Under the third row bench seat in
the tool bag
Removing the jack and tools
1. Lift the 3rd row seat cushion.
2. Remove the jack assembly from the bag under the seat.

Removing the spare tire
1. Open the liftgate, locate the U-shaped slits in the carpet, and flip up
the piece of carpet to expose the hex nut.
2. Insert the lug nut wrench on the
hex nut in cargo floor.
3. Turn the wrench
counterclockwise until tire is
lowered to the ground and the cable
is slightly slack.
4. Remove the retainer from the
spare tire. It may be necessary to
lift one end of the tire to disengage
the retainer

Jul 12, 2009 | 2002 Mercury Villager

1 Answer

2002 Chevy 1/2 ton broken window cable power window


The only way the parts are available is to buy the window regulator assembly.

Jun 14, 2009 | 2002 Chevrolet Silverado

2 Answers

How do I replace broken 2002 buick century passenger side mirror?


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Oct 09, 2008 | 2002 Buick Century

2 Answers

2002 door panel


There is a special tool you can purchase to remove the quick fasteners. If you don’t want to buy one you can use a flat blade screwdriver. Be real careful the fasteners will break easy.

Jul 12, 2008 | 2002 Buick LeSabre

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...