Question about 1994 Jeep Grand Cherokee

1 Answer

How to replace a fuel pump on a 1994 jeep grand cherokee?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 17,970 Answers

I'm assuming that your Jeep have a 5.2L V8 engine (as mine), then check this procedure...

Grand Cherokee 5.2L Engines
(see Figure 6)

  1. Disconnect the negative battery cable.
  2. Open the radiator valve and drain the cooling system.
  3. Remove the cooling fan and shroud as an assembly.
  4. Remove the accessory drive belt.
  5. Remove the water pump pulley from the hub.
  6. Disconnect the hoses from the water pump.
  7. Loosen the heater hose coolant return tube mounting bolt and nut and remove the tube. Discard the O-ring.
how to replace a fuel pump on a 1994 jeep grand - 25b04d0.jpg

Fig. 6: Water pump mounting bolt locations
  1. Remove the water pump mounting bolts.
  2. Loosen the clamp at the water pump end of the bypass hose. Slip the bypass hose from the water pump while removing the pump from the engine. Discard the gasket.
To install:
  1. Clean all gasket mating surfaces.
  2. Guide the water pump and new gasket into position while connecting the bypass hose to the pump. Tighten the water pump bolts to 30 ft. lbs. (40 Nm).
  3. Install the bypass hose clamp.
  4. Spin the water pump to ensure the pump impeller does not rub against the timing chain cover.
  5. Coat a new O-ring with coolant and install it to the heater hose coolant return tube.
  6. Install the coolant return tube to the engine. Ensure the slot in the tube bracket is bottomed to the mounting bolt. This will properly position the return tube.
  7. Connect the radiator hose to the water pump.
  8. Connect the heater hose and clamp to the return tube.
  9. Install the water pump pulley and tighten the bolts to 20 ft. lbs. (27 Nm).
  10. Install the accessory drive belt.
  11. Install the cooling fan and shroud.
  12. Fill the cooling system.
  13. Connect the negative battery cable.
  14. Start the engine and check for leaks.

Other details can find in your repair manual ZJ-Secc-7-Cooling-System

Hope thats help.

Posted on May 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Jeep grand cherokee won't start - will start on starter fluid - tried throttle position sensor already and codes are just coming up 55 each time tried


did you check the fuel pump or the fuel pump relay? first, check the fuel pump relay, located inside the power distribution center. the power distribution center is located next to the battery.

Apr 16, 2010 | 1994 Jeep Grand Cherokee

1 Answer

My 1994 Jeep Grand Cherokee has a no start problem. I have tested the fuel pump and it is fine. However, there is no fuel pressure at the fuel rail.


If pump is running, then two other places to look are the fuel filter and regulator. GC of that year may either have regulator on fuel rail and filter in line near l/r wheel, or both as one unit on the tank on top of the sending unit.

Jul 14, 2009 | 1994 Jeep Grand Cherokee

1 Answer

Jeep won't go over 60 mph loss of power


Check for a clogged catalytic conveter or weak fuel pump. Remove the O2 sensor so exhaust can flow out hole and test drive it. If it's better replace the cat or look for kinked or dented section of the exhaust. If it didn't help, have the fuel pressure tested as well as the ignition advance and timing chain.

Apr 16, 2009 | 1994 Jeep Grand Cherokee

1 Answer

Removal of fuel pump from fuel pump module in a 94 jeep cherokee


are u sure its removeable i know on some models u replace the whole assembly how is it sold did u buy the new part

Mar 31, 2009 | 1994 Jeep Grand Cherokee

1 Answer

Looking for fuel pump in jeep cherokee 1994


It is in the fuel tank. You have to remove the fuel tank to replace the fuel pump. Instructions for doing this can be found here.

Jan 29, 2009 | 1994 Jeep Grand Cherokee

1 Answer

Jeep won;t start..new fuel pump installed


try the fuel filter and make sure you have proper oil pressure!! Remeber if you have tried craking to many bad times then the plugs are going to be fouled out!! Means that they are going to be drowned with gas and need replacing!! Also make sure your fuel pump is coming on!! You should hear a hissin or a hummin noise back from the fuel tank!

Dec 07, 2008 | 1994 Jeep Grand Cherokee

Not finding what you are looking for?
1994 Jeep Grand Cherokee Logo

687 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...