Question about 1994 Nissan King Cab

Open Question

How do replace the starter on a 1994 6 cylinder 4wd auto nissan truck

Posted by on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: replacing a starter and starter

I also have the same problem i replace the starter and cylinode and im still having no luck i get a click when i turn the key

Posted on Oct 04, 2008

  • 337 Answers

SOURCE: how do i replace the

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528018d0be

Posted on Dec 19, 2008

  • 1024 Answers

SOURCE: need photos of alternator and starter wiring on 93

there are 4 wires go to alternator
2 white wires go to battery
1 black wire goes to ground
1 yellow/black goes to bulb check relay
starter has only two wires
the big one goes to the battery and the small one goes to ignition system. you can not mix the terminals because the size of the studs on the starter

Posted on Mar 07, 2010

  • 610 Answers

SOURCE: i have a 1994 nissan truck with a bad head gasket

Check with a local salvage yard, as they have the Hollander interchange info, that tells what will swap with what. Make sure you offer a little comp for their trouble, as this information costs them money to have! If you are lucky, and it does swap, make sure you remove the pilot bearing or bushing from the hole in the rear of the manual trans engine"s cranckshaft, as it won't mate up otherwise. Good luck, and feel free to contact me with any other questions!

Posted on Jan 15, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dosent start makes a clicking sound


Manual Transmission, or Auto? If Manual, when it doesn't start, does it click once when you turn the key, but nothing else happens? If so, replace the Clutch Relay - under the hood on the passenger side fender. I've done this a few times on my Nissan. Cheap part ($30), but incredibly irritating when it starts acting up. If you hear repeated clicking, it's either the starter or solenoid, so a starter replacement would be in order.

Mar 16, 2014 | 1994 Nissan Pickup

1 Answer

What are the possible solutions if my 1994 Nissan altima has a brand new clutch kit and everything seems to work good even the transmission but the car just want engage?


have you checked the fluid in the clutch master cylinder? look under the hood on the drivers side, on the firewall. looks like a brake master cylinder,takes regular brake fluid. if low,top it off with brake fluid and keep pumping it[the clutch pedal] until it works right. you may also have a bad clutch slave cylinder[located on the side of your transmission] it may be bad. it's not uncommon for it to go bad at any time. it's called a slave cylinder,or hydraullic clutch cylinder. you can purchase it at most auto parts stores,such as auto zone or advance auto parts. wish you the very best of luck,thank you for choosing fixya.com

Feb 27, 2011 | 1994 Nissan Altima

1 Answer

How do i change the starter motor on a 1993 pathfinder


  1. Remove the exhaust manifold heat insulator.
  2. Remove the fuel tube retainer bolt.
  1. On 2wd models with the 6-cylinder engine:
    1. Remove the front right wheel.
    2. Remove the front gravel shield.
    3. Remove the exhaust manifold heat insulator.
    4. Remove the exhaust manifold.
    5. Detach the oil pressure switch connector.
  2. Unfasten the remaining electrical connections at the starter solenoid.
  3. Remove the two nuts holding the starter to the bell housing, then pull the starter toward the front of the vehicle and out.

To install:

  1. Insert the starter into the bell housing, being sure that the starter drive is not jammed against the flywheel.
  2. Tighten the attaching nuts and secure all electrical connections to the starter assembly.
  3. Install all remaining components in reverse order of removal.
  4. Reconnect the battery cables. If applicable, refill and check the oil level. Check the starter assembly for proper operation.



// // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 31; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]> var _strTreeScrollHidName = 'ctl00_hidTreeScrollPos'; c17hydro_100.gif

Starter removal on 2WD-6-cylinder engine






c17hydro_101.gif

Starter removal on 4WD-6-cylinder engine


On 4wd models with the 6-cylinder engine:

Remove the front gravel shield.

    1. Detach the oil pressure switch connector.
    2. Drain the engine oil and remove the oil filter.

Jan 19, 2011 | 1993 Nissan Pathfinder

1 Answer

How do you remove the starter from a 1991 nissan pic up with 2.9 cc engine


I did not find the instructions for a 2.9 L engine per se, but the following should be good for many American models of the 1991 Nissan d21 Pickup truck: REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable at the battery, then disconnect the positive battery cable at the starter. Fig. 1: Starter removal on 4WD - 6-cylinder engine 86713015.gif
    Fig. 2: Starter removal on 2WD - 6-cylinder engine 86713016.gif

  2. On 4wd models with the 6-cylinder engine:
    1. Remove the front gravel shield.
    2. Detach the oil pressure switch connector.
    3. Drain the engine oil and remove the oil filter. CAUTION
      The EPA warns that prolonged contact with used engine oil may cause a number of skin disorders, including cancer! You should make every effort to minimize your exposure to used engine oil. Protective gloves should be worn when changing the oil. Wash your hands and any other exposed skin areas as soon as possible after exposure to used engine oil. Soap and water, or waterless hand cleaner should be used.
    4. Remove the exhaust manifold heat insulator.
    5. Remove the fuel tube retainer bolt.
  3. On 2wd models with the 6-cylinder engine:
    1. Remove the front right wheel.
    2. Remove the front gravel shield.
    3. Remove the exhaust manifold heat insulator.
    4. Remove the exhaust manifold.
    5. Detach the oil pressure switch connector.
  4. Unfasten the remaining electrical connections at the starter solenoid.
  5. Remove the two nuts holding the starter to the bell housing, then pull the starter toward the front of the vehicle and out. To install:
  6. Insert the starter into the bell housing, being sure that the starter drive is not jammed against the flywheel.
  7. Tighten the attaching nuts and secure all electrical connections to the starter assembly.
  8. Install all remaining components in reverse order of removal.
  9. Reconnect the battery cables. If applicable, refill and check the oil level. Check the starter assembly for proper operation.
prev.gif next.gif

Oct 07, 2010 | 1991 Nissan Pickup

1 Answer

Auto trans fluid capacity


On a 1994 Nissan Pickup, the auto transmission capacity is 8 3/8 quarts for a 2WD, and 9 quarts for a 4WD.

Jul 31, 2010 | 1994 Nissan Pickup

1 Answer

Where is the starter in a 1995 nissan pathfinder


Nissan Pick-ups and Pathfinder 1989-1995
Starter - REMOVAL & INSTALLATION
(see Figures 1 and 2)
  1. Disconnect the negative battery cable at the battery, then disconnect the positive battery cable at the starter.
4178adf.jpg


Fig. 1: Starter removal on 4WD-6-cylinder engine

74f3669.jpg

Fig. 2: Starter removal on 2WD-6-cylinder engine
  1. On 4wd models with the 6-cylinder engine:
    1. Remove the front gravel shield.
    2. Detach the oil pressure switch connector.
    3. Drain the engine oil and remove the oil filter.
CAUTION The EPA warns that prolonged contact with used engine oil may cause a number of skin disorders, including cancer! You should make every effort to minimize your exposure to used engine oil. Protective gloves should be worn when changing the oil. Wash your hands and any other exposed skin areas as soon as possible after exposure to used engine oil. Soap and water, or waterless hand cleaner should be used.
  1. On 2wd models with the 6-cylinder engine:
    1. Remove the front right wheel.
    2. Remove the front gravel shield.
    3. Remove the exhaust manifold heat insulator.
    4. Remove the exhaust manifold.
    5. Detach the oil pressure switch connector.

  2. Unfasten the remaining electrical connections at the starter solenoid.
  3. Remove the two nuts holding the starter to the bell housing, then pull the starter toward the front of the vehicle and out.

Hope this help (remember rated this).

May 18, 2010 | 1995 Nissan Pathfinder

1 Answer

Need a manual to change the starter on a, 1994 Nissan, Quest mini van + 6 cylinders


http://groups.yahoo.com/group/villagerquest/

Section 03-06: Starting System 1996 Villager Workshop Manual
REMOVAL AND INSTALLATION Starter Motor stv~us~en~file=ani_caut.gif~gen~ref.gif WARNING: WHEN SERVICING THE STARTER MOTOR OR PERFORMING OTHER UNDERHOOD WORK IN THE VICINITY OF THE STARTER MOTOR, BE AWARE THAT THE HEAVY GAUGE BATTERY INPUT LEAD AT THE STARTER SOLENOID IS "ELECTRICALLY HOT" AT ALL TIMES. A PROTECTIVE BOOT IS PROVIDED OVER THIS TERMINAL ON ALL VEHICLE LINES AND MUST BE REPLACED AFTER SERVICING. BE SURE TO DISCONNECT THE BATTERY GROUND CABLE BEFORE SERVICING THE STARTER MOTOR.
Removal
  1. Disconnect the battery ground cable (14301).
  1. Remove the engine air cleaner (ACL) (9600). Refer to Section 03-12 for the removal and installation procedure.
  1. Slide back the protective boot and remove the nut securing the battery positive cable on the B-terminal of the starter solenoid (11390).
  1. Remove the battery positive cable from the B-terminal.
  1. Disconnect the S-terminal electrical connector.
  1. Remove the two starter motor bolts.
  1. Remove the starter motor (11002) from the vehicle.

Apr 27, 2010 | 1994 Nissan Quest

1 Answer

I need to know how to get the bolts off a nissan pathfinders starter motor


Nissan Pick-ups and Pathfinder 1989-1995
Starter - REMOVAL & INSTALLATION
(see Figures 1 and 2)
  1. Disconnect the negative battery cable at the battery, then disconnect the positive battery cable at the starter.
e757468.jpg
Fig. 1: Starter removal on 4WD-6-cylinder engine


4643c02.jpg
Fig. 2: Starter removal on 2WD-6-cylinder engine
  1. On 4wd models with the 6-cylinder engine:
    1. Remove the front gravel shield.
    2. Detach the oil pressure switch connector.
    3. Drain the engine oil and remove the oil filter.
CAUTION The EPA warns that prolonged contact with used engine oil may cause a number of skin disorders, including cancer! You should make every effort to minimize your exposure to used engine oil. Protective gloves should be worn when changing the oil. Wash your hands and any other exposed skin areas as soon as possible after exposure to used engine oil. Soap and water, or waterless hand cleaner should be used.
  1. On 2wd models with the 6-cylinder engine:
    1. Remove the front right wheel.
    2. Remove the front gravel shield.
    3. Remove the exhaust manifold heat insulator.
    4. Remove the exhaust manifold.
    5. Detach the oil pressure switch connector.

  2. Unfasten the remaining electrical connections at the starter solenoid.
  3. Remove the two nuts holding the starter to the bell housing, then pull the starter toward the front of the vehicle and out.
To install:
  1. Insert the starter into the bell housing, being sure that the starter drive is not jammed against the flywheel.
  2. Tighten the attaching nuts and secure all electrical connections to the starter assembly.
  3. Install all remaining components in reverse order of removal.
  4. Reconnect the battery cables. If applicable, refill and check the oil level. Check the starter assembly for proper operation.

Also can check here other DIY.

Hope helped with this (remember rated and comments this help).

Mar 03, 2010 | 1995 Nissan Pathfinder

Not finding what you are looking for?
1994 Nissan King Cab Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...