Question about 2000 Kia Sephia

1 Answer

2000 sephia,car is blowing left side tail lamp/parking lamp fuse,also at the same time the left side turn signals are blinking fast like a blown bulb would do,however the bulbs work fine.any ideas and is this a common problem for these cars.thanks

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 72 Answers

Check all the grounds on the front fenders and in the trunk near the tail lampsclean these up and put star washers between cable end and ground

Posted on May 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I'm needing the wiring diagram for my 2007 Chevrolet Impala LT 3.5 tail lights.


Go to http://www.bbbind.com/free_tsb.html free wiring diagrams ! You having tail light problems ? Do you know how they work ?

They are turned on by the BCM !
Park, Tail, Marker and License Lamps
The park, tail, license, and marker lamps are turned ON when the headlamp switch is placed in either the HEAD or PARK lamp positions, or anytime the automatic light control (ALC) turns the headlamps ON. When the headlamp switch is placed in the park lamp or headlamp positions, ground from G202 is applied through the signal circuit to the BCM indicating the park lamp request. In response to this signal, the BCM applies ground through the park lamp relay control circuit energizing the PARK LP PCB Relay. With the relay energized, battery voltage is applied through the switch side of the relay, both park lamp fuses, and the supply voltage circuits illuminating the park, tail marker, and license lamps. Ground for the left front park and marker lamps is provided at G101 and the right front park and marker lamps at G100. Ground for all rear lamps is provided at G302.
Turn Signal Lamps
The LT T/SIG and RT T/SIG fuses located in the underhood fuse block supplies battery positive voltage to the body control module (BCM) for turn signal and hazard lamp operation. When the turn signal switch is place in either the LEFT or RIGHT position, ground from G202 is applied through the turn signal switch signal circuit to the BCM indicating the turn signal request. In response to this signal, the BCM applies a pulsating voltage to the front and rear turn signal lamps supply voltage circuits cycling the lamps ON and OFF. The BCM also sends a message via GMLAN to the instrument panel cluster (IPC) to cycle the turn signal indicator ON and OFF depending on the position of the turn signal switch.
Ground for the turn signal lamps is supplied as follows:
?€¢
G101 provides ground for the left front turn signal lamp


?€¢
G100 provides ground for the right front turn signal lamp


?€¢
G302 provides ground for the left and right rear turn signal lamps

May 03, 2016 | 2007 Chevrolet Chevrolet Impala LT

2 Answers

My turn signal fuse blowed got new one now they dont work why


canada or USA, (diffr. laws, different wiring, even DRL up there)
station wagon or NOT?
THE TURNS FUSE BLEW OUT. 2nd time, 3rd,,,?????
that means the circuit is overloaded or shorted.! (prevents fire)
but did it blow a 2nd time, why not say so???

all 4 lamps dead. or stuck on, or flash odd. or what? dim?
does the cluster lamp flash, , in blink or emerg. mode?
wont work , means what, (dead or stuck on or dim)?????
do emergency flashers work? ,dead, stuck on what?
does car drive perfect day or night?
are any other things on car dead, of odd acting?
we see all this , 1st 5 min in a shop, zero here.
ive answered Forenza blinks here, many times.
ever search?

ill now answer by guessing USA non stationwagon and no DRL.
dash box fuse 4 kills blinkers

EF1 (engine fuse) 1 good?
dash fuse 14 and EF1 can kills emerg. flasher

so of Emergancy flash lamps blows fuse 14,(smaller of 2)
then the blinkers are in fact shorted.
does it?
if yes, then find out which side blows the fuse 3.
turns left blow or turns right blows.
so if say turns right blows, F4 fuse.
if true ?remove all bulbs front rear right bulbs.
does the fuse hold now,(means not blown)
then buy new lamps there. problem solved
bulbs can in fact short.
not just blow open.
Tell the full story and all this gets easy.
For sure emergency flash,

26123255-vhg5j1pxaeih5p05yacvrs2p-1-0.jpg

Mar 09, 2016 | 2007 Suzuki Forenza Sedan

3 Answers

Turn signals not working


all else on car works perfectly (other shoe drops??????)
waring 1: no scan tool, you will fail (99%)
is battery fully charged to 12.6vdc rested or at 10v?
all 4 corners dead?
not working means dead?, flashes too fast/slow or dim? or they stick on? (5 modes to fail not counting L/R and haz)
do the hazards work? (prime evidence and not stated)
most cars before 2007 have fuse marked TURN.
but not this car... its not at all like older cars....
did you scan it first after the fuse tests? any PCM scan tool.?
2009 WK jeep
the FSM chapter 8L shows the huge list of errors the lamps can fail. DTC errors.
in fact 8 blinker codes, ! DTC errors,

there is no fuse, just for turns, (trailer lamps fuse 19)

read this excerpt from the FSM book.

The turn signal system operates on battery current received on a fused ignition switch output (run) circuit so that the
turn signals will only operate with the ignition switch in the On position. The hazard warning system operates on
non-switched battery current received on a fused B(+) circuit so that the hazard warning remains operational regardless
of the ignition switch position. When the turn signal system is activated, the circuitry of the left multi-function
switch and the FCM will cause the selected (right or left) turn signal indicator, front park/turn signal lamp, front side
marker lamp and rear tail/stop/turn signal lamp to flash on and off. When the hazard warning system is activated,
the circuitry of the hazard warning switch and the FCM will cause both the right side and the left side turn signal
indicators, front park/turn signal lamps, front side marker lamps and rear tail/stop/turn signal lamps to flash on and
off. The Front Control Module (FCM) can also activate the hazard warning system lamps.
end quote)

the module front control MFC, runs this
and it uses fuse 18 , if 18 blows the module goes off line and vast things fail and huge numbers OF DTCs store.
and fuse 27 MFC
MFC needs these fuses good.
keep in mind nobody has MFC internal schematics...so........



this module drives left and right side front and rear.
electronic drivers, not fuses.
the MFC is here.
the fuses are 12,13,18, 20,27 that power MFC.


25812039-lb3yimx2pwhstnjl4tgwffiq-2-0.jpg ground this end.

Aug 07, 2015 | 2009 Jeep Grand Cherokee

1 Answer

No tail lights on my 2008 ford escape. driver rear blinker wasn't working. replaced bulb, but when i turn on the blinker both blinkers are blinking...front and back...


Not sure I follow your story.
The front and rear turn signal should blink on one side. If the tail lamps are not working, it could be a fuse or a problem with the wiring. And the tail lamps are on the same circuit as the front parking lamps.

Feb 26, 2014 | 2008 Ford Escape

2 Answers

No tails on 2003 Envoy fuse is good


There are several things that could be the problem, but first, I would have to know EXACTLY what IS working and what IS NOT working to isolate the problem.
1. Is it just your rear park (or running) lamps not working? One side? or Both sides? (they have separate fuses.)
2. Are the FRONT park lamps working? (Again, separate fuse, but powered by the same MAIN feed.)
3. Are your Brake and Turn signals working? One side? Both sides? Front AND Rear for turn signals?
4. Have you tried changing bulbs already? (It IS possible to have two blown bulbs at the same time)

Get back to me with this information and I will try to isolate the possibilities for you.

Jan 28, 2011 | 2003 GMC Envoy

1 Answer

Signal lights, fuse box and signal light relay in 2001 Volkswagen


The bulbs on these cars can be delicate. Some get replaced every year or so-( headlights, tail and brake) and some I've never touched in 8 years (my front turn signals and marker lights)

The fast blinking occurance is normal when a turn signal bulb goes out.

The rear lights are common to blow, I keep spares in the glovebox.

Make sure you were given the correct bulb, check to see that it works and isn't defective. Also there is an empty spot in the rear bulb holder- make sure you didn't mistakenly pop a bulb in there cause' it won't work.

The front right signal light is in the right headlight housing. Open the hood and on the back of the housing there are two plastic caps. One is curved and one is rectangular- you want to take off the rectangular one.

Open the drivers door and on the side of the dash there's a cover. This is the main fuse block. Use a coin or carefully with a screwdriver pry it open. To check a fuse pull it out, noting exactly where it came from, and visually inspect it to see if it is blown.

Fuse # 2- turn signal system
Fuse #4- License plate lights
Fuse #7- back up lights
Fuse #13- brake lights
Fuse #22- parking and side marker lights, right
Fuse #23- parking and side marker lights, left

The turn signal flasher is integrated into the hazzard button in the center of the dash. If all else is good and you suspect the flasher is bad, which is a good possibility, call a VW dealer and have them run your VIN# to check for recalls. The hazzard switch for some cars around your year had a recall on em'.





Jan 01, 2010 | 2001 Volkswagen Jetta TDI

2 Answers

Tail lights work on both sides. turn signal and


Sounds like you need to replace the drivers brake/tail light.

Dec 14, 2009 | 1998 GMC Sierra

1 Answer

Right hand side tail light short circuit Fuse blows even with all three bulbs removed


you must have another bad lamp either in the front turn/parking light circuit or the left side rear tail, cause most tail light fuses feed all 4 sides

Nov 01, 2009 | 2007 Chevrolet Aveo Sedan

2 Answers

2002 Hyundai elantra driver side turn signal not working outside


This simply means that the front driver side turn signal bulb has failed. Replace it.

Oct 28, 2009 | 2000 Nissan Maxima

2 Answers

2001 Explorer Sport ,Rear Driver Brake Light and Turn Sig. Broke


Rear lights are double filament bulbs one side for the lights other side for the brake/turn signals so it still may be a bulb. Do u have a test light or volt meter you can check to make sure u have power there when brakes or turn signals are activated. Or just try another bulb.

Feb 12, 2009 | 2001 Ford Explorer Sport

Not finding what you are looking for?
2000 Kia Sephia Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...