Question about 1999 Lexus RX 300

1 Answer

Brake lights dont work changed bulbs , fuse , and stop light switch any ideas

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,033 Answers

Check to see if you are getting power to the fuse, Next check the power going to the brake switch. After you check for the power going into each location, and you find the one that's not getting the power, you may have a bad wire, also check to see if the brake switch is set up right to depress when applying brakes.

Posted on May 03, 2010

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: brake lights went out, changed bulbs, checked fuse, still wont work

You have to check the brake light switch which should be around the brake pedal on the upperside.
Ones located rremove the wires tht go to the switch and jump them by using a piece of wire, thn check if the brake lights come 'on'. If they do , thn its the switch tht may need replacing or even sometimes adjusting inorder to operate.
Hope this helps.

Posted on May 10, 2009

  • 1 Answer

SOURCE: No brake lights. Fuse good. Changed brake

this was a recall

Posted on Jun 13, 2009

chuck943
  • 783 Answers

SOURCE: change the bulb in brake light, still dont work fuses are good

Go to this website: http://www.genuineservice.com/genuineservice/en/default?page=genuineService Pick owner guide on the left task bar and then input your vehicle info. Then pick get owner guide and pick onwer guide 1st printing. Your fuse info begins on page 189.

Posted on Jun 16, 2009

  • 491 Answers

SOURCE: 2003 Impala Brake lights dont work

The brake lights are routed through the signal light switch.
Looks like that will be the next switch to replace and the problem.

Posted on Sep 07, 2009

  • 280 Answers

SOURCE: ford focus brake light failure !!!

1 - are you SURE theyre the right bulbs! - if theyre too bright they can blow the fuse, if theyre the wrong type of bulb they will blow the fuse.. best get the bulbs direct from ford, they are always in stock, so are the proper fuses.
2 - theres a center brakelight isnt there? check this bulb too for proper wattage and size/shape
Other than that maybe the wiring in the boot is damaged and shorting?? -----
Leave feedback good or bad.

Posted on Jan 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Turn signal and brake light not working.


Change the bulb.The bulb has two lights.Running,and brake light turn signal.Its the bulb

Apr 14, 2013 | 2004 Chevrolet Silverado 1500

3 Answers

Brake light dont work, change bulbs, fuse, bake switch, and has power still dont work


You have a failed brake lamp relay,this is located at the back right hand in the trunk at the quater panel.

Mar 12, 2012 | 2003 Honda Civic

1 Answer

2000 300M. no brake lights. changed switch, not it. checked all fuses, not it. changed all bulbs, not it. Was burnt bulb on deck lid light though. Help Please! All other lights and signals work. ...


Dont just go replacing parts, that gets expensive and a lot of work and you have not fixed anything. First at the switch, make sure the Pink/Dk Blue wire is hot. (fuse #20) and then when brake pedal is depressed the White/Tan wire should be hot. From there it goes to the Stop lamps. You dont say if the high mounted stop lamp works or not ( I ASSUME not??? working) You say the bulb was burned out, but not if it works or not??? there is connector C200 that is between the switch and the lights. its located just to the left of drivers feet, in the kick panel...but you really need to verify if you have power to the White/Tan wires at the rear tail lights.

Dec 01, 2010 | 1999 Chrysler 300M

2 Answers

Turn signals work but the brake lights do not how do i get them to work? i already changed the flasher.


I have a 2001 Ford F150, my brake lights dont work. Ive replaced the bulbs, checked the fuses,and the brake switch on side of the brake pedal was replaced. I still dont have any brake lights. My third brake light works fine, along with my running lights,flashers, blinkers.

Jun 18, 2009 | 1985 Ford F150

1 Answer

Brake lights went out, changed bulbs, checked fuse, still wont work


You have to check the brake light switch which should be around the brake pedal on the upperside.
Ones located rremove the wires tht go to the switch and jump them by using a piece of wire, thn check if the brake lights come 'on'. If they do , thn its the switch tht may need replacing or even sometimes adjusting inorder to operate.
Hope this helps.

May 10, 2009 | 2002 Nissan Xterra

1 Answer

All brake lights suddenly stopped working changed bulbs park light fuse and cant find any blown fuses what else can it be


brake switch on the pedal bad.bad relay. do you have a second fuse box if so check it. look at the wiring see if it is frayed or chafed check the connections.check all the fuses not just the ones labeled brakes.switch the relay with one that you know is good like turn signal and see if the turn signal works then check brakes.use a 12 volt test light check the brake switch and probe the wires. hope this helped if not write back and i'll give you more ideas.

Apr 24, 2009 | 1996 Buick Park Avenue

1 Answer

Brake light's and horn dont work


disconect the break light switch and link a piece of wire between the two terminals and the break lights should come on

Dec 25, 2008 | 1995 Subaru Impreza

2 Answers

Brake lights dont work


i have a 1999 malabu and my brake lights went out i checked all fuses and changed all the bulbs and i also have no tail lights what could it be.

Jun 06, 2008 | 2005 Chevrolet Malibu

Not finding what you are looking for?
1999 Lexus RX 300 Logo

266 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

874 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...