Question about 1991 Chevrolet Corsica

1 Answer

Where is the crankshaft position sensor located on a1991 chevy corsica 2.2 engine

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 76 Answers

The sensor is located Under hood, center, rear engine area, below ingnition coil pack and DIS module, mounted in engine block. It has the small elec. connecting plug.

Posted on May 03, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the crankshaft position sensor located in the 1990 Chevrolet Corsica 4 cylinder 2.2 liter engine?


Follow this link to a diagram that will show you where it's located. Hope this helps.

Jul 11, 2016 | Chevrolet Cars & Trucks

1 Answer

Where is the crankshaft sensor on a 93 chevy corsica 3.1 engine?


chevy corsica 3.1L crank sensor is located on the front of the engine above the starter.

Feb 28, 2012 | 1993 Chevrolet Corsica

1 Answer

96 corsica has spark and gas wont start


Bad sensor most likely. Crankshaft position sensor and car wont run at all or maybe for a second. Also depends if anything weird happened before it was turned off that would reveal more. Usually a bad sensor will cause stalls before a no start. Bad injectors can cause but you would have a stall out also. If pump and spark your computer is working, and ASD relay and pump. I'd lean toward a sensor and crankshaft sensor would cause that but a pain to replace depending where it located.

Sep 02, 2010 | 1996 Chevrolet Corsica

1 Answer

WHERE IS THE CRANK SHAFT SENCER LOCATED ON THE MOTOR


The 2 crankshaft sensors are located on the front of the engine block, between cylinder Numbers 4 and 6. Crankshaft position A sensor is located on the upper crankcase and crankshaft position B sensor is located in the lower crankcase. Both sensors extend into the crankcase and are sealed into the engine block with O-rings. The crankshaft position sensors are not adjustable.

Jun 08, 2010 | 1998 Cadillac Catera

1 Answer

Jsut want to know where crankshaft position sensor


Hi!!

here are illustrations of the CKP (crankshaft position) sensor in 2.3L and 3.0L.

Note: In the bottom of the 2.3L drawing says Trottle Position (TP) Sensor, this is wrong, It should say CKP Sensor.


2.3L Engine


The Crankshaft Position (CKP) sensor is located to the left of the crankshaft pulley.

0996b43f80202990.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Crankshaft Position (CKP) sensor location-2.3L engine


3.0L Engine


The Crankshaft Position (CKP) sensor is located just behind the crankshaft pulley on engine block.

0996b43f8020299e.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Crankshaft Position (CKP) sensor location-3.0L engine

The cost of the sensor is $23 bucks at AutoZone.

If helpful, click below

Apr 15, 2010 | 2002 Ford Escape

2 Answers

Were is the crankshaft position sensor located on 2001 chevy mali


It mounts in the side of the block near the crankshaft,it fits in a hole,going into the engine block.,look on the inside of the engine compartment ,on the firewall side,left of the pulleys,down low.

Mar 22, 2010 | Chevrolet Malibu Cars & Trucks

1 Answer

Crankshaft position sensor location


1990 Chevrolet Cavalier 2.2L TBI 4cyl
The Crankshaft Position Sensor is located under hood, center, rear engine area, below ingnition coil pack and DIS module, mounted in engine block.

87c675c.jpg

Fig. 1: View of the CKP sensor-to-crankshaft reluctor relationship

Crankshaft Position (CKP) Sensor
A magnetic crankshaft sensor (Hall Effect switch) is used which is remotely mounted on the opposite side of the engine from the DIS/IC module. The sensor protrudes in to the engine block, within about 0.050 in. (1.27mm) of the crankshaft reluctor.

I really hope help you wuth this (rated this help). have a nice day, good luck.

Sep 25, 2009 | 1990 Chevrolet Cavalier

3 Answers

Im not getting any spark in my 96 Corsica


Ignition module may be bad. It should be located under the coils, the coils usually plug into the ignition module. Also might be a bad crank or cam sensor

Sep 11, 2009 | 1996 Chevrolet Corsica

1 Answer

Location of crank position sensor on 92 chevy corsica 3.1


You will have a no start or stalls after engine gets hot and then cools down restarts, the sensor is on the front of the engine mounted into the cam gear cover if it is not visiable get under the, (here is a picture) car and look.d37e0b9.jpg

Jan 21, 2009 | 1988 Chevrolet Corsica

Not finding what you are looking for?
1991 Chevrolet Corsica Logo

332 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8201 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...