Question about 2000 Ford Taurus

1 Answer

How to replace power steering line hose - 2000 Ford Taurus

Posted by on

Ad

1 Answer

It unbolts. What do you want to know? Most likely need metric wrenches.

Posted on May 03, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How involved is it to replace a power steering pump on a 2007 Explorer 4.0?


Power Steering Pump - 4.0L Special Tool(s) Installer Set, Teflon® Seal
211-D027 (D90P-3517-A) or equivalent Material Item Specification MERCON® V Automatic Transmission Fluid
XT-5-QM (or XT-5-QMC) (US); CXT-5-LM12 (Canada) MERCON® V
Item Part Number Description 1 388898 Teflon® seal 2 - Pressure line-to-pump fitting (part of 3A719) 3 W700839 Power steering pump bolts (3 required) 4 3A674 Power steering pump 5 W503924 Pressure line bracket-to-engine bolt 6 3691 Power steering pump supply hose 7 W503924 Power steering pump supply hose bracket bolt
Removal
NOTICE: While repairing the power steering system, care should be taken to prevent the entry of foreign material or failure of the power steering components may result.

  1. Using a suitable suction device, remove the power steering fluid from the reservoir.
  1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02.
  1. Remove the power steering pump pulley. For additional information, refer to Power Steering Pump Pulley - 4.0Lin this section.
  1. Remove the pressure line bracket-to-engine bolt.
  1. Remove the power steering pump supply hose bracket bolt.
  1. Release the power steering pump supply hose clamp and disconnect the hose.
  1. Disconnect the pressure line-to-pump fitting.
    • Remove and discard the Teflon® seal.
  1. Remove the 3 bolts and the power steering pump.
Installation
  1. NOTE:A new Teflon® seal must be installed.Using the Teflon® Seal Installer Set, install a new Teflon® seal to the pressure line fitting.
  1. Position the power steering pump and install the 3 bolts.
    • Tighten to 25 Nm (18 lb-ft).
  1. Connect the pressure line-to-pump fitting.
    • Tighten to 75 Nm (55 lb-ft).
  1. Connect the power steering pump supply hose.
  1. Install the power steering pump supply hose bracket bolt.
    • Tighten to 11 Nm (97 lb-in).
  1. Install the pressure line bracket-to-engine bolt.
    • Tighten to 11 Nm (97 lb-in).
  1. Install the power steering pump pulley. For additional information, refer to Power Steering Pump Pulley - 4.0Lin this section.
  1. Fill the power steering system. For additional information, refer to Section 211-00.

Apr 13, 2016 | Ford Cars & Trucks

1 Answer

Power steering fluid leak in 99 Toyota Corolla


look for split in the hard line where fluid is leaking. If you see split, change the line only. make sure power steering reservoir is filled and rack and pinion is full (charge with steering wheel left/right motion). You should be able to remove wheel and inside wheel panel to see power steering fluid shooting out of any hole. There is hydraulic pressure on the lines.

Apr 03, 2014 | 2003 Kia Spectra

1 Answer

Replace pressure house on 1985 mustang


For procedure to replace power steering hoses,click the link below :----http://technoanswers.blogspot.in/2012/02/how-to-replace-power-steering-pressure.html
----------Also its advisable to go through this additional help links.Click the link to go through the procedures:----How to Remove Power steering Pressure Hose?

http://schematicsdiagram.blogspot.com/2011/12/how-to-remove-power-steering-pressure.html


Vacuum hose Routing diagram?

http://repairhelpcenter.blogspot.com/2011/11/vacuum-hose-routing-diagram-for-acura.html


Ac line and evaporator drain hose?

http://repairhelpcenter.blogspot.com/2011/10/ac-line-and-evaporator-drain-hose-on.html


How to disconnect the hose form the Evap Canister?

http://schematicsdiagram.blogspot.com/2011/12/how-to-disconnect-hose-form-evap.html


Vacuum Hose Routing Diagram For Throttle Body?

http://schematicsdiagram.blogspot.com/2011/12/vacuum-hose-routing-diagram-for-1995.html


How exactly the Vehicles A/C Hose works?

http://repairhelpcenter.blogspot.com/2011/11/how-exactly-vehicles-ac-hose-works.html


HOW TO REPLACE AN UPPER RADIATOR HOSE

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-upper-radiator-hose.html
HOW TO REPLACE A LOWER RADIATOR HOSE

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-lower-radiator-hose.html



Fail smog test due to gas filter hose?

http://repairhelpcenter.blogspot.com/2012/01/fail-smog-test-due-to-gas-filter-hose.html


EGR Hoses melting?

http://repairhelpcenter.blogspot.com/2011/12/egr-hoses-melting.html


EVAP connecting hose to PCV valve Collapse?

http://schematicsdiagram.blogspot.com/2012/01/evap-connecting-hose-to-pcv-valve.html


--------How to replace Power steering rack and pinion gear? http://technoanswers.blogspot.in/2012/02/how-to-replace-power-steering-rack-and.html
--------How to replace Power Steering Pump?

Also bleeding:

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-power-steering-pump-on.html

----------------
How to replace Steering Linkage? http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-steering-linkage-on.html
-----Car steering wheel makes noise?

http://schematicsdiagram.blogspot.com/2011/12/car-steering-wheel-makes-noise.html

------
Car makes clicking or tapping sound? http://schematicsdiagram.blogspot.com/2011/12/car-makes-clicking-or-tapping-sound.html
---------This will help.Thanks.

Feb 16, 2012 | 1985 Ford Mustang

1 Answer

HOW DO I REPLACE THE HIGH PRESSURE LINE FOR A POWER STEERING UNIT ON A 1998 MUSTANG?


Disconnect battery ground cable.
Remove engine Air Cleaner (ACL) .
Disconnect electrical connector in back of engine cooling fan motor.
Remove radiator fan shroud.
Disconnect constant control relay module harness from headlamp harness and place constant control relay module on top of engine to provide accessibility to power steering lines.
Remove wiring harness guide retaining screws and position guide aside.
Remove screw at power steering hose bracket.
Remove anti-rattle clip.
Remove plastic strap retaining tubes to power rack and pinion steering gear.
Remove power steering pressure hose at power steering pump.
Remove power steering pressure hose at power rack and pinion steering gear.
Remove power steering pressure hose from vehicle.
Reverse procedure to install new hose.
Fill and bleed power steering system.

Aug 20, 2011 | Ford Mustang Cars & Trucks

1 Answer

1998 silverado...no power brakes or steering


Hydra boost brakes? On a 1500? Is it a diesel? Pump is full of fluid? Can you explain which hose he did this to?

Apr 03, 2010 | 1988 Chevrolet C1500

1 Answer

Need to replace high pressure power steering hose on 2004 Monte Carlo SS. Need tips to effectively do the job myself. Tools needed, tricks to make the job easier, what not to do...etc. Thank yiou so much...


Power Steering Line/Hose: Service and Repair
Pressure Hose
Power Steering Pressure Pipe/Hose Replacement (3.8L)
Removal Procedure
1. Place a drain pan under the vehicle.
2. Remove the accessory drive belt.
3. Raise and support the vehicle. Refer to Vehicle Lifting.
4. Remove the tire and wheel assembly.
5. The power steering pressure hose is the lower hose at the power steering gear.
Remove the power steering pressure hose from the power steering gear.
6. Remove the power steering pressure hose from the power steering pump.
7. Remove the power steering pressure hose from the clamps on the power steering gear.
8. Remove the power steering pressure hose from the vehicle.
Installation Procedure
1. Install the power steering pressure hose to the vehicle.
2. Install the power steering pressure hose to the clamps on the power steering gear.
Notice: Refer to Fastener Notice in Service Precautions.
3. Install the power steering pressure hose to the power steering pump.
^ Tighten the fitting to 27 Nm (20 ft. lbs.).
4. Install the power steering pressure hose to the power steering gear.
^ Tighten the pressure hose fitting to 27 Nm (20 ft. lbs.).
5. Install the tire and wheel assembly.
6. Remove the drain pan from under the vehicle.
7. Lower the vehicle.
8. Install the accessory drive belt.
9. Fill the power steering system with power steering fluid.
10. Bleed the power steering system.
11. Inspect the power steering system for leaks.

00d203e.jpg

Sep 15, 2009 | 2004 Chevrolet Monte Carlo

1 Answer

Subaru impreza 1993 power steering leak


YOU CANT USE A REGULAR FUEL LINE ON POWER STEERING AS A HIGH PRESSURE HOSE.BECAUSE POWER STEERING PRESSURE IS 1000 PSI.YOU HAVE TO BUY THE POWER STEERING HIGH PRESSURE HOSE IT HAS NUMBER OF PLIES MATERIAL WEAVES TO MAKE IT STRONG.IT WAS MADE FOR POWER STEERING HIGH PRESSURE.YOU DONT HAVE A BLOCKAGE .THE HIGH PRESSURE HOSE JUST WORE OUT.REPLACE IT .IT SHOULD FIX THE PROBLEM.

Sep 04, 2009 | 1993 Subaru Impreza

1 Answer

HOW DO YOU TAKE OFF A POWER STEERING LINE? I HAVE A 96 FORD E150 5.8


When power steering hose replacement is required, follow these steps:
  1. With the engine stopped, remove the return hose at the power steering gear, and allow the fluid to drain from this hose into a drain pan. On some cars, the vehicle must be lifted on a hoist to replace the power steering hoses.
  2. Loosen and remove all hose fittings from the pump and steering gear.
  3. Remove all hose-to-chassis clips.
  4. Remove the hoses from the chassis, and cap the pump and steering fittings.
  5. If O-rings are used on the hose ends, install new O-rings. TRW steering gear cylinder lines have gaskets that are serviced as a unit. The old gasket must be pried out of the fittings in the housing before the new lines and gaskets are installed. Lubricate O-rings with power steering fluid.
  6. Reverse steps 1 through 4 to install the power steering hoses. Tighten all fittings to the manufacturer's specified torque. Be sure all hose-to-chassis clips are in place. Do not position hoses where they rub on other components.
  7. Fill the pump reservoir to the full mark with the manufacturer's recommended fluid. Bleed air from the power steering system. Check the fluid level in the reservoir and add fluid as required.

Jul 07, 2009 | 1996 Ford Econoline

1 Answer

Do you have the steps to replace the pump


Notes Power steering pump, replacing

Note: As the illustrations in this service information are used for different model years and/or models, some variation may occur. However, the essential information in the illustrations is always correct.

Preparation

Warning: Used fluid is considerably more dangerous than new fluid. Avoid skin contact with the oil.

Remove

  • the oil hose from the mounting on top of the power steering pump
  • the auxiliaries belt.
Note: If there is dirt in the fluid, drain the system and remove the hoses from the steering gear.

Removing the power steering pump/engine strut
Applies only to diesel cars:

Remove

113652509


  • the screw at the pump
  • the screw at the engine.
Leave the strut hanging in the delivery line.

Removing the feeder hose and delivery line
Install

113652510


  • the lock grip pliers on the feeder hose as close to the power steering pump as possible
  • the lock grip pliers on the return hose at the fluid reservoir.
Note: Place paper over the generator (GEN) as protection against oil.

Remove

  • the screw nipple. Remove the delivery line from the pump
  • the hose clamp. Remove the feeder hose from the power steering pump.
Warning: Avoid skin contact with the oil.

Removing the power steering pump
Remove

113652511


  • the 3 screws
  • the servo pump.
Installing the power steering pump
Install

  • the servo pump
  • the three screws. Tighten to 25 Nm .
Installing the power steering pump
Install

  • the feeder hose. Tighten the clamp
  • the delivery line. Do not tighten yet.
Installing the power steering pump/engine strut
Applies only to diesel cars:

Install

  • the strut
  • the screw at the engine. Tighten to 24 Nm
  • the screw at the pump. Tighten to 24 Nm .
Finishing
Tighten the delivery line. Tighten to 25 Nm .
Remove paper and lock grip pliers.
Install the auxiliaries belt.

113652512



Jun 06, 2009 | 2004 Volvo XC90

1 Answer

Power steering


Go to a parts store and tell them you want power steering return hose or transmission cooler hose. It comes in bulk, they can just cut off how much you need.

Mar 25, 2009 | 2001 Dodge Caravan

Not finding what you are looking for?
2000 Ford Taurus Logo

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...