Hi i have a problem with 2 electrical windows i try already from all switches and they are not going down i don't know if is any fuse or the problem is the motors can you help me please this is a 98 jetta gls

None of the windows work ? You say fuses are good , which fuses ? Did you pull them all out an look at them ? Did you check for power - battery voltage at the window switches ? There is a driver door module involved !

• Power Windows Completely Inoperative

• Supply open or shorted.
• Ground open.
• Window regulator control switch inoperative.
• Circuits open or shorted.
• Window regulator electric drive inoperative.
• Driver door module.

• PERFORM driver door module self test. Service DTCs. If no DTCs are retrieved, GO to Pinpoint Test C .

If you don't know electrical circuit testing suggest you take to a AES certified repair shop ! If you plan to do this anyway your going to need a wiring diagram , wiring harness layout , volt ohm meter !
Basic Electricity for Service Techs Ohm law Current Flow Opens Shorts

Hi,
The problem would be the power window switch assembly! That switch controls the power to ur window motors! If u are a tinkering man, try to borrow from any garage/friend w/ the same window switch and test it!
Or
Go to ur service center and have them check it for free... they always try the new switch... and you will know the main prob!

if it works intermittanly then its not the fuse. In my opinion its 1 of 3 things. Either first the power connector going from the fuse to the window has a loose connection. 2 the switch itself has failed thus working intermittanly. 3 the motor is failing on the window. This should be the first 3 places you check but if you want to check the fuse its located in the high current fuse box in the engine compartment. An is D and is a 40a fuse. If you need further assistance please let me know, Thanks, Midwest-tek

Hello! Turn the ignition switch on...Hold the master power window auto up switch for five seconds...Send a comment with results...


Guru........Saailer


I’m happy to help further over the phone at https://www.6ya.com/expert/david_6df67de3b14de867

i have an 03 g35 coupe and my driver's window just doesnt go back up! i tried looking for a fuse for the power window but couldnt find it and my passenger window works just fine! what possibly solutions do i have?

hi there

there are three things that would cause this problem

1. the window motor is bad
2. the fuse that controls the window is blown

3. most common is the window switch its self

this is the most common cause
if the motor was going out it would make a noise or go down very slow but going down is easier then up so thats what makes me think switch or fuse

don

This is One with the Power Window SWITCH in the CENTER Console they Often Get Liquids SPILLED on them Causing them to Fail, I Would First Check for 12volts @ the Switch with KEY ON. With a Sure 12volts Going IN the Switch Check for 12 Volt going OUT, If Switch IS BAD there Will be NO 12volts Coming OUT With this Go on to Switch Replacement


REMOVAL PROCEDURE

1. Use a flat-bladed tool in order to remove the power window switch bezel (1) from the console.
2. Remove the electrical connection from the power window switch (2).
3. With a flat-bladed tool release the power window switch (2) tabs, and remove the switch from the power window bezel (1) retainers.

INSTALLATION PROCEDURE \

1. Install the power window switch (2) into the power window switch bezel (1) until fully seated.
2. Connect the electrical connector to the power window switch (2).
3. Install the power window switch bezel (1) to the floor console.

((((>>>All of this is Assuming that All FUSES Related to And RELAYS Related to Windows Have Been Deemed GOOD & Funktional<<<<)))
If Further HELP / SUPPORT / INSTRUCTIONS Are needed P L E A S E Dont RULE me Out as I have the Answers, Just Try to be as Spisific as Possible and I will be More than HAPPY to Help you With your Needs of Auto Repair

1. Install the power window switch (2) into the power window switch bezel (1) until fully seated.
2. Connect the electrical connector to the power window switch (2).
3. Install the power window switch bezel (1) to the floor console.

Does the switch work the other windows? if not the switch is broken. Although it may just be the window in question with a faulty switch
If the motor was broken theres usually (not always) noise involved.
Pry out the switch and use an electric meter to test it.
The fuse will normally control more than 1 window, so if its blown, they will all not work.
be careful trying to raise the glass again.
Hope that helps.