Question about 2007 Toyota Sienna

Open Question

Replace the rear window wiper blade on a 2007 Toyota Sienna

How do you replace the rear window wiper blade on a 2007 Toyota Sienna?

Also, how do you adjust the positioning of the wiper arm?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
bibleman01
  • 334 Answers

SOURCE: remove rear wiper blade on saab 9-5 estate

Best way go to a parts store and ask for help and they would probably slip it on for you
God Bless you Greg

Posted on Dec 03, 2008

Ad
  • 1 Answer

SOURCE: How do I change a rear wiper blade on a 2004 Toyota Sienna

This is a dealer item. You will not find anywhere esle.

Posted on Dec 26, 2008

dgjtex
  • 405 Answers

SOURCE: 04 dodge ram 1500 wiper arm goes down before going up

remove wiper arms at the shaft, right at the cowl. each will have a nut on them but it is covered by a piece of plastic that will snap up for access. take nuts off and remove wiper assembly. turn key on turn wipers on make sure shafts turn when on, then turn off the shafts to stop in park position. then reinstall wiper assemblies in their park position .

Posted on Dec 29, 2008

  • 1861 Answers

SOURCE: 1998 Toyota Sienna Windshield Wipers not working

The fuse is the 20 amp WIPER fuse, located in the fusebox under the driver side of the dash, farthest on the left, 2nd one up from the bottom.

Posted on Jan 02, 2009

alicantecoli
  • 22219 Answers

SOURCE: wiper blade does not hold tight to rear window,is

oil the hinge and make sure spring hasnt corroded away ,if it appears ok pull arm up put a cardboard on screen or blanket ,then bend arm over a bit to increase the pressure

Posted on Jan 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace 2006 Sienna wiper arm


check that the rubber blade is free to move in the arm guides

Apr 08, 2014 | Toyota Sienna Cars & Trucks

1 Answer

How do you replace the rear wiper on a 2009 Scion XD?


You can make use of following procedure to replace rear wiper in ur scion xd.
Pull the rear wiper arm away from the rear window in order to access the wiper blade.

  • Locate the hinge where the blade mechanism meets the wiper arm and squeeze the plastic tabs on the blade in order to release it from its locked position on the arm. In some cases, instead of tabs, there is a small button that must be pressed to release the wiper from the arm.
  • Detach the blade from the arm and slide the old blade out. Insert the new blade into the wiper arm and lock the blade in place.
  • Return the wiper arm to its set position. Before driving, wet the window and test the wiper to make sure it is operating properly.
  • Dec 14, 2010 | 2009 Scion xD

    1 Answer

    How do I replace wiper blades


    First, pull on the wiper arm until it raises and locks into the service position. The wiper arm will stand by itself once you raise it past a certain point.
    Then find the clip on the underside of the wiper arm (rotate the blade slightly to get to it.
    Press the clip in while simultaneously pulling the old wiper blade off the wiper arm. You can then discard the old blade.
    Align the new wiper blade with the wiper arm track. Slide it along the track until you hear it click.
    Repeat this process with the other wiper blade to complete the replacement of wiper blades on your Highlander.
    Return the wiper arms to their normal position against the windshield. Done!

    Dec 05, 2010 | 2005 Toyota Highlander

    1 Answer

    I need to adjust the wiper arm on a 1997 suburban, it hits the side of the window.


    Wiper Arm & Blade (Front) Removal & Installation Wiper Blade To Remove:
    1. Turn ignition switch to ACCY position.
    2. Turn wiper switch to PULSE position and turn ignition OFF when wipers are stopped in the innerwipe position.
    3. Push the wiper blade clip button IN and remove wiper blade from wiper arm.
    To Install:
    1. Insert wiper arm hook through opening in wiper blade.
    2. Place wiper blade pivot in the inside radius of wiper arm hook.
    3. Pull on wiper blade pivot into hook until it locks into place.
    4. Check wipers for proper operation.
    Wiper Arm To Remove:
    NOTE: Mark position of wiper blade on windshield to ensure proper position upon reassembly.
    1. Remove washer hose.
    2. Lift wiper arm from windshield and use a screwdriver to disengage retaining latch.
    3. Remove wiper arm from shaft.
    To Install:
    1. Place wiper arm on shaft so that wiper arm aligns with marks placed on windshield.
    2. Press arm assembly on shaft and push retaining latch IN.
    3. Connect washer hose.
    4. Remove windshield markings and check wipers for proper operation.
    prev.gif next.gif

    Oct 26, 2010 | Chevrolet Suburban 1500 Cars & Trucks

    1 Answer

    How does one change the wiper blades (front and back) on a 2004 Toyota Sienna minivan?


    Pretty simple, they both just snap out of the connector on the wiper arms. If you buy your wipers at Walmart or most major parts stores they will install them for free.

    Apr 03, 2010 | 2004 Toyota Sienna

    1 Answer

    The rear wiper blade no longer works


    new rear motor, or linkage inside door broke, or wire broke

    Jan 04, 2010 | 2004 Toyota Sienna

    1 Answer

    How to replace the wiper insert at the back of


    moz-screenshot.jpg
    1. REMOVE RR WIPER BLADE
      1. Raise the rear wiper blade to the position as shown in the illustration where the meshing of the claw disengages with a clicking sound. NOTE: Be careful not to break the claw.
      2. Pull straight the rear wiper blade to vehicle's left from the wiper arm. NOTE: Do not fold the rear wiper arm with the rear wiper blade removed from it.1722d05.gif

    1. REMOVE REAR WIPER RUBBER
      1. Place the rear wiper with the rear end of the rubber protruded from the blade stopper as shown in the illustration. NOTE: Do not pull out the wiper rubber forcibly, as the backing plates will become deformed or the blade claws will become damaged. HINT: The rubber can be easily pulled out by pushing the middle area of the blade.
    f54b10a.gif
    1. INSTALL REAR WIPER RUBBER
      1. Install the 2 wiper rubber backing plates to the rear wiper rubber. NOTE: Be careful to observe and keep direction of curvature for correct replacement.
    0dd144d.gif
    b. Insert the rear wiper rubber from the claw of the middle of the rear wiper blade into the rear end position.
    8f40009.gif
    c. After passing the rear wiper rubber through the rear end side claw, protrude it from the rear end stopper and pass it through the front tip side claw.

    Sep 12, 2009 | 2005 Toyota Matrix

    3 Answers

    How do you change the rear wiper blade on a 2007 Prius


    either you go to the dealor and get a whole new arm wich is toyotas solution to the problem or you go to the auto parst store and ask them for 16 inch insert not a blade just an insert most stores will even instal it for you

    Aug 26, 2009 | 2007 Toyota Prius

    1 Answer

    Replace rear wiper 2007 RAV-4?????


    Slide a small screwdriver under the tab in the middle of the blade and the arm, while pressing the tab in, pull blade away from the arm, this may need some extra wiggle. Remember you dont want it to fall off when driving..

    May 07, 2009 | 2007 Toyota RAV4

    2 Answers

    How do I change a rear wiper blade on a 2004 Toyota Sienna


    You gotta flip the wiper arm up, and turn the blade out. Underneath you will find a tab in the center. Press in on this tab and slide the blade out.

    Dec 20, 2008 | 2004 Toyota Sienna

    Not finding what you are looking for?
    2007 Toyota Sienna Logo

    Related Topics:

    491 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Toyota Experts

    yadayada
    yadayada

    Level 3 Expert

    76682 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8531 Answers

    Are you a Toyota Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...