Question about 1996 Jeep Grand Cherokee

1 Answer

Where is the location of the crank shaft position sensor

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 193 Answers

It's in the back passenger side of the engine. It gets it's trigger from the flywheel.

Posted on May 03, 2010

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: crank shaft position sensor

i know myne is under the starter have to drain a little oil

Posted on Feb 28, 2009

  • 383 Answers

SOURCE: CRANK SHAFT POSITION SENSOR 20002 NISSAN ALTIMA

1st, Nissan had a recall on Crank position sensors for 2002-2006 Altima's. Check with you dealer before you go doing any repairs. You may discover you can get your car repaired at no charge.
NHTSA Campaign ID number :O7V527000
Symptom: Erratic behavior. Stalling and no starts and very difficult to diagnose due to the time frame in which the component actually malfunctions. The warranty should not be limited to the original owner.
I would also need more specifics as to which engine you have so I might assist you in where the location of the sensor is. The Altima had a 4 and a 6 cyl engine offered that year.

Posted on Apr 06, 2009

blueextc3221
  • 15935 Answers

SOURCE: Need to find Camshaft position sensor and crank se

CRANKSHAFT SENSOR - Under hood, center, front engine area, rear of crankshaft pulley, mounted in timing cover assembly.

afa767f.gif
CAMSHAFT SENSOR - Under hood, passenger side, upper engine area, mounted on engine in front of camshaft.
4c3af2b.gif
Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

Posted on Apr 08, 2009

tracer_steve
  • 59 Answers

SOURCE: crank shaft position sensor located hyundai sonta 2004 v6

On a 2.7L it is located above and to the right of the starter. You will have remove the starter heat shield to gain access to it.

Posted on Jun 25, 2009

  • 4 Answers

SOURCE: Crank shaft sensor location.

Underneath on the transmission housing.

Posted on Jul 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is crank shaft sensor location on 95 lexus sc300 please help


images for Where is crankshaft sensor location on 95 ...

eplaced engine on '97 SC300 now new engine does not have Crank ...

www.clublexus.com/.../633233-replaced-engine-on-97-sc300-now-new-...
May 4, 2012 - Location: arizona. Posts: 3 ... apparently 95-97s had an additional crank sensor. .... 1995 Lexus SC300 5spd Na-T ( TT Ecu Mod + a few others) 2jzge position sensor??
Nov 2, 2011
SC400 Crank Shaft Position Sensor. WHERE?????
Oct 11, 2011
SC300 No Spark
Oct 2, 2010
What happens if the Camshaft Position Sensor goes bad?
Jun 18, 2009
More results from www.clublexus.com

Lexus Crank Position Sensor ' LS400 SC300 ES300 GS300 ...

www.partsgeek.com > Crank Position Sensor > Lexus Parts & Accessories
Products 1 - 10 of 68 - 95 1995 Lexus LS400 Crank Position Sensor Denso NLA 7/13 ... 96 1996 Lexus SC300 Crank Position Sensor Denso Includes Pigtail.

Jan 27, 2016 | Lexus Cars & Trucks

1 Answer

Where is the 2nd crank shaft sensor located, and is there a diagram to show where these sensors are located?


is it a no crank or crank no start?
Possible causes for code P0335
- Faulty crankshaft position sensor
- Crankshaft position sensor harness is open or shorted
- Crankshaft position sensor circuit poor electrical connection
- Signal plate may be damage
- Starter motor may be faulty
- Starting system circuit
- Dead or weak battery

Read more: http://engine-codes.com/p0335.html#ixzz3Cxw6SN6O

Sep 10, 2014 | 2004 Buick Rendezvous

1 Answer

Locate crankshaft sensor on 1996 crystler New yorker (where is the crank shaft found on a 1996 Crystler NewYorker?


The crank shaft is actually an internal mechanical part of the engine (see last picture) however the crank shaft position sensor uses through what they call a "hall effect" with a componant inside the transmission. The crank shaft turns which in turn turns the componant inside the transmission. Below are a couple of pictures of the location of the crankshaft position sensor as well as what the plug looks like so you know you are removing the correct part. Hope this helps.....

1_17_2012_1_55_30_pm.jpg

1_17_2012_1_55_54_pm.jpg

1_17_2012_1_56_30_pm.jpg

1_17_2012_1_56_58_pm.jpg

1_17_2012_1_57_19_pm.jpg

Jan 17, 2012 | Cars & Trucks

1 Answer

Crank shaft position sensor code. Where is the crank shaft position sensor located?


The crankshaft sensor is located just above the the oil filter, which is by the front of the engine, by the firewall. I reached it from underneath the car. There is one bolt holding it in place.

Jul 15, 2011 | 2002 Chrysler PT Cruiser

1 Answer

Where is the crank shaft position sensor located


the crank shaft position sensor is part of the timing belt system. if your going threw the trouble of doing the sensor consider doing the timing belt as well heres a pisture to help you locate it. hope this helpsonetufshoppe_72.gif

Jan 28, 2011 | 2005 Kia Sorento

1 Answer

Where is the Crank Shaft Position Sensor located?


The crank shaft position sensor is located just above the starter on the front of the engine block.If your not sure what you can do is purchase one and then look at the connector end to see if it looks the same.Hope this helps.Good luck.

Nov 06, 2010 | 2000 Oldsmobile Intrigue

1 Answer

Where is the crank shaft positioning sensor located on a 01' Cherekee Sport with a 4 liter? What are the symptoms of a faulty Crank shaft positioning sensor?


Look at the area around the crankshaft pulley. It's bolted to the block and senses the crank position. If it fails, You won't have an ignition spark. Good Luck, Ned

Aug 27, 2009 | Jeep Cherokee Cars & Trucks

2 Answers

CRANK SHAFT POSITION SENSOR 20002 NISSAN ALTIMA


1st, Nissan had a recall on Crank position sensors for 2002-2006 Altima's. Check with you dealer before you go doing any repairs. You may discover you can get your car repaired at no charge.
NHTSA Campaign ID number :O7V527000
Symptom: Erratic behavior. Stalling and no starts and very difficult to diagnose due to the time frame in which the component actually malfunctions. The warranty should not be limited to the original owner.
I would also need more specifics as to which engine you have so I might assist you in where the location of the sensor is. The Altima had a 4 and a 6 cyl engine offered that year.

Dec 18, 2008 | 2005 Nissan Altima

Not finding what you are looking for?
1996 Jeep Grand Cherokee Logo

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...