Question about Cars & Trucks

1 Answer

1992 Metro: I have a 1992 metro conv. and I'm just trying to f...

I have a 1992 metro conv. And I'm just trying to find out the correct idle speed?

Posted by Anonymous on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Hi 900 revs.

Posted on May 03, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am looking for the parking lite fuse on 1992 geo metro conv


that means there is short in the park lamp feed.
its the largest feed on all cars, and very hard to find, if visuals of harness show no damage, and you remove all 4 tail and front light bulbs. the light blubs with brass (yellow) metal bases, LOVE to short.
remove all 4 and try new fuse.
http://www.fixkick.com/power-elect/blows-fuse.html

all ways to find a short are there ,even Duanes video.

Jul 08, 2014 | 1992 Geo Metro

1 Answer

Motor runs at 4000 rmp when started


1995 Geo Metro. COLD start or HOT started or BOTH?
Does it ever idle down to 800 HOT? (engine temp)>?

Aka:
Geo Metro (later re-branded the Chevrolet Metro), Pontiac Firefly, and Suzuki Swift
which engine, what country???
I will post for USA only !!!!
Auto or stick tranny???
the USA 1995 was the last car to use TBI injection (throttle body)
the LSI option, then had a 4 cylinder. in 1.3Liters.
and works totally differ. than any 1.0L
answsering for 1.0L

Have you inserted the Diagnostic jumper wire and looked at the
FLASH codes yet?
choke? on 95? what country is this, ours are not carbs. in 1995.
so post country. ours are all EFI in USA.
3 cylinder? 1 liter? or which engine/?
on any USA Metro, 1L , when first started, it has 2 valves. to control IDLE, (cold , is iAC) hot is ISC, The cold start valve opens farther the colder it is (how cold was it). but usually is limited to about 2000 rpm
max.
this engine, TBI, uses a MAP to control fuel mixtures, and
any air leaks (aka; vacuum leaks) what so ever, will cause too fast idle.
so on MAP cars, you get to find out what is leaking AIR.
1995 has the new better , idle control speed motor, (ISC)
this can be stuck open.
that new TPS, did you do the calibration correctly?
it must set right. or idle will never be controlled.
finding the cause, takes hard work, and hands on testing
A/C fast idle broken
A/T transmission fast idle, device, broken.
Air leaks (add huge list of possibles and cracked hoses here)
Throttle stuck
ISC or IAC bad.
very hands on to find this, done many.
TPS on indexed corrrectly or not calibrated.

Jan 28, 2014 | 1995 Geo Metro

1 Answer

Auto trans will shift some times and manual only


It may be just the vehicle speed sensor. Does the speedometer work OK? The vehicle speed sensor tells the computer how to control the shifting and it also sends a signal to the speedometer. Is the trany full of fluid, is it fairly clean? It should be red. Most vehicles, you check the fluid with the engine idling, in park.

Dec 12, 2009 | 1992 Geo Metro

1 Answer

1992 Geo Metro Convertible. I cannot get the top


DId you remember to push (depress) the small, square button to the right, first?

Jun 06, 2009 | 1992 Geo Metro

1 Answer

When i start my 1997 Geo Metro, it often sputters


Try this
Here are the most common causes of surges, stalls at stops, low erratic idle speed, rough idle and engine hesitation, it is in most cases the idle speed control air-bypass valve and or throttle valve and upper intake, these area's get full of gunk and combustion residue over the miles and cause idle issues (stalls, low idle) like yours, Get a can of intake cleaner from any local parts store, not carb spray, intake cleaner, it is made by a company called CRC, remove the air intake hose to the engine, hold the idle high so the engine won't stall, then spray the can of cleaner into the intake while keeping the engine running, use at least 1/2 the can, shut down the engine and disconnect the battery for 5 minutes, then restart and complete a number of mixed driving cycles, town, freeway, stop and go etc., after a few days the problem will go away as the system will relearn to the clean intake.

Apr 03, 2009 | 1997 Geo Metro

1 Answer

THE FIRING ORDER FOR A 1992 GEO METRO


The firing order is 1-3-2,   distrubtor rotates counter clockwise. looking at engine from front of vehicle cyl. # 1 will be on your left cyl.# 2 center and cyl.# 3on your right.

Nov 28, 2008 | 1992 Geo Metro

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...