Question about Mazda B2600

1 Answer

Am I able to remove the hydralic lifters from a G6 engine without taking the engine out of the car

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Yes you can,, just replace it with a common jumper,

Posted on May 03, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to know how to adjust valve lash on a big block 454 with roller rocker arms and hydralic roller lifters ? A video whould really help


The old fashioned way was to connect everything up and tighten the nut on the lifters until you could no longer turn the pushrod and then add about a quarter turn. Cover the lifters with a rag then start the engine with the valve cover off and loosen one lifter at a time until you hear it clicking and then tighten just until the clicking stops. Do that on all lifters ona at a time. Whe complete go back and add one quarter turn to each lifter.

Sep 12, 2013 | Cars & Trucks

1 Answer

After changing my thermostat in my 1996 eagle vision tsi i now have a clunking noise in engine. i have taking apart the entire engine and put it back together and the noise is still there what coul


when you put it back together did you soak the lifters in oil for 24 hours or at all , this noise could be anything I would have to see it and hear it , this is hard to tell when not there

Sep 23, 2012 | 1995 Eagle Vision

1 Answer

Sounds like teppets are noisy


you could need valve clearance adjustment or need oil and filter change oil is dirty.causing dirt particles stop up hydralic lifter bleeder holes stopping lifters from pumping oil.or lifters worn out.and oil passages in engine block restricted with sludge.

Apr 29, 2011 | Renault Sport Cars & Trucks

1 Answer

My engine has a ticking at start up and goes away after a few minutes? I put some motor honey in it and it is better. what could this be?


It sounds as if the hydrallic lifters are bleeding off pressure after it sits. Which means the lifters somewhat collapse until they start getting oil pressure from the oil pump after you start it. You might try an oil change and an A/C oil filter. If it is the lifters, they would need to be replaced.

May 15, 2010 | 2002 Cadillac Deville

2 Answers

How do i ajust my lifters on a chevy 350 tbi


they are hydralic and are not adjustable during normal maintenence
if you removed heads then you need to adjust them
if they are clicking then a lifter may be bad or the cam shaft is going flat

Mar 22, 2010 | 1992 Chevrolet K1500

1 Answer

Power steering reservoir Pontiac G6


some G6 do not have power streeing pumps
they have ELECTRIC POWER STEERING
all depends on the engine
2.2 4cylinder have electric
3.5V6 can have one or the other
if you have a V6 then you will see the power steering cap through the engine cover on the right side if it has hydralic power steering

Dec 23, 2009 | 2005 Pontiac G6

2 Answers

1992 jeep cherokee 4.0 can I remove the lifters without removing the cylender head?


Sorry...lifters will not come out without removing the cylinder head

Nov 14, 2009 | 1992 Jeep Cherokee Sport

1 Answer

Lifter noise.


since the 4.2L is a push rod engine, you have the 4.6L or 5.4L which the valve train system is the same. The lifter can be removed without removing the camshaft by using two special tools that can be purchased from any tool house that sells special tools in your area. Tool 1 is a spacer to prevent the valve from traveling too far (damage to seal), Tool 2 is a valve spring compressor, that uses the camshaft as a fulcrum to depress the valve and spring enough to remove the rocker assembly, use a plastic pen to determine piston location before using the compressor tool, you want the piston approximately 1-2 inches below TDC, once the rocker assembly is removed the lifter can be pulled out the top. It is very improtant that the rockers and lifters be kept together by location (ie. exhaust number 3 rocker and lifter together) and installed back in thier original positions. If you can not get the special tools, then the only other option is to remove the cams. Hope this helps, let me know

Jun 01, 2009 | 2004 Ford F150

2 Answers

Dodge Caravan 2000, 3 l engine, 109000 km/ mechanical valve lifters that are out of adjustment


The next time you do an oil change, put a liter of tranny fluid in with the oil BEFORE you change it. Let it run for an hour or two.The tranny fluid will clean out the gunk that causes your lifters to stick.Now do your oil change. Do this each time you change your oil, only use a 1/2 liter each time. You will be amazed at the difference, I was.

Jun 05, 2008 | 2000 Dodge Caravan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

119 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...