Question about 2004 Dodge Ram 1500

2 Answers

The key will not turn in the ignition. The

The key will not turn in the ignition. The steering is not locked and it is in park. Any other causes?

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,319 Answers

You have bent tumblers inside the lock cylinder. A replacement will be needed for this repair. The old one is unuseable since the tumblers are stuck inside and the key does not turn it no longer

Posted on May 03, 2010

Testimonial: "That makes sense. thanks."

Ad
  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

For most cars and trucks the steering wheel must be locked for the key to turn. try pushing the brake and turning the steering wheel from one side to the other. once the wheel locks the key should turn and then u can start the truck.

Posted on May 03, 2010

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

SOURCE: key not turning, steering not locking, trans in

GM has had problems with the ignitions they use for years. Only option is to replace the tumbler assembly (ignition switch). If you have security installed theirs a special procedure to relearn the key.

Posted on Jul 14, 2009

freetek
  • 5568 Answers

SOURCE: A4 steering lock does not engage and car won't turn over

The steering locks don't necessarily engage when the key is removed, I always turn the wheel before exiting to engage it. There are several positions that will allow the pin to lock in but if between these, it may seem that it isn't locked.

Posted on Aug 23, 2008

frcs68
  • 1605 Answers

SOURCE: Ignition Lock

sprey some dw40 into the lock cylinder and try again.
you may have to wait a little while or repeat the porces several times, it will turn......

Posted on Oct 30, 2008

  • 2 Answers

SOURCE: Locked ignition and steering column

either you have the wrong key,or try turning the steering wheel to the right all the way,then turn key,this usually happens when you park the vehicle and the wheels are turned,then the steering wheel locks hard

Posted on Nov 16, 2008

  • 1 Answer

SOURCE: can't turn key in ignition lock cylinder 2000 dodge stratus

heat it up with a hair dryer

Posted on Jun 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need help with ignition switch on 2002 grand prix..keys stays in got it out try it again and sticks in again.


Does the vehicle start an run ?Can you turn the key to the off position ? And the key won't come out ? Did you try some key graphite ( lube ) ? New lock cylinder need maybe . Or is it a problem with
Steering Column Electric Park Lock
If the vehicle is equipped with a floor-mounted console gear shifter, an added safety feature is an steering column electric park lock system in the steering column. The steering column electric park lock system prevents the steering wheel from being locked when the transmission is in gear and the vehicle may be moving. The column ignition lock system consists of a steering column electric park lock and a park position switch, that is located in the A/T shift lock control switch. The steering column electric park lock contains a spring-loaded pin that mechanically prevents the ignition key cylinder from being turned to the Lock position when the transmission is not in the Park position. If vehicle power is lost or the transmission is not in the Park position, the operator will not be able to turn the ignition key to the Lock position and will not be able to remove the ignition key from the column.

Oct 30, 2017 | Cars & Trucks

1 Answer

How to remove my Keys from 2003 envoy they are stuck


Ignition Lock Cylinder Control Actuator
If the vehicle is equipped with a floor mounted console gear shifter, it has a ignition lock cylinder control actuator system in the steering column as an added safety feature. The ignition lock cylinder control actuators purpose is to prevent the steering wheel from being locked when the transmission is in gear and the vehicle may still be moving. The column ignition lock system consists of a ignition lock cylinder control acutator, and a park position switch that is located in the A/T shift lock control switch. The ignition lock cylinder control acutator contains a pin that is spring loaded out to mechanically prevent the ignition key cylinder from being turned to the lock position when vehicle transmission is not in the Park position. If vehicle power is lost, and/or the transmission is not in the Park position the operator will not be able to turn the ignition key to the lock position and will not be able to remove the ignition key from the column. GM has had some problems with this , If you have the console shifter there is a micro switch that when put into park a linkage pushes on this micro switch closing the circuit to ignition lock cylinder control actuator allowing you to remove your key ! These linkages fall out causing this problem ,an have electrical wiring problems as well ! I fixed a 2006 Chevy cobalt that had this same problem by getting a used shifter assembly at the auto salvage year ! cost $20.00 . There mite be a access hole under the bottom of the steering column with a release button up inside !

Apr 17, 2015 | 2003 GMC Envoy

3 Answers

Key will not turn in ignition


Probably because your steering lock is activated, if not then you have forced the ignition too much and it needs to be replaced.

Try the following:
Insert Key in ignition
Turn Steering Wheel to left side as much as it can when engine isnt started (apply some force), then try to see if key will turn in ignition.

If it doesn't work: Try same maneuver but turn Steering Wheel to the right instead.

Apr 06, 2015 | 2002 GMC Envoy

2 Answers

I have a 95 camaro, I put the key in ignition and it will not turn the ignition. It's like it's stuck. Replaced the ignition module and still cannot turn ignition. Help!


the ignition module (ignition switch on top of the steering column) normally doesn't get stuck.

things you can try:
steering wheel lock: (the pin gets a "burr" on it and locks everything up) wiggle steering wheel back and forth while trying to turn key.

transmission lock (parking on an incline will jam up the interlock)
push the shifter farther into park while trying to turn the key, or wiggle shifter

Sep 19, 2014 | 1995 Chevrolet Camaro

2 Answers

Why ignition won't turn


By far the most likely reason that one can't turn the key in the ignition is because the car was parked with the wheels turned. There is a security feature that locks the steering when the key is removed to prevent a thief from driving the car.
When the car is parked with the front wheels other than strait, the weight of the car will cause the wheels to try to straiten, If this engages the steering lock pressure is put on the ignition switch.
To start the car, look to see what direction the wheels are pointing. grasp the steering wheel and turn it TOWARD the direction the wheels are turning and now start the car.
Other causes may include wrong key, damaged ignition or other causes that may require a professional.

Aug 16, 2014 | 2009 Nissan Versa

2 Answers

Why won't my ignition key turn over and my steering wheel is locked in place at the sametime?


I'm assuming you mean your key wont turn in the ignition. first off check to make sure the car is in park. then what you gotta do is put in the key and put a little pressure as if turning but dont turn too hard, then even though the steering wheel is locked you will have to try to move it a little, if you parked with your tires turned then you will want to try to turn the wheel in the same direction, (even locked you should be able to move it about a half inch) you will have to turn the wheel hard but it should move enough to allow the key to turn, you may have to jiggle the key a little in the ignition but it should eventually turn, just remember not to try turning the key too hard, the extra force wont make it go but can cause the key to break. this tends to happen when you turn the car off andthe steering wheel gets locked if the wheels are turned hard in either direction. also if multiple attempts at this still dont work, try taking the key out and turning it over and trying again. Even though both sides of the key are identicle, because of wear on the key and the ignition, sometimes when the wheel locks the ignition, it will only turn if the key is put in a certain way. Hope this helps, good luck

Aug 29, 2012 | 2002 Pontiac Montana

1 Answer

The ignition wont turn at all and car is locked in park position.


IF you are parked with your wheels turned a little, sometimes the steering can get into kind of a bind and the steering wheel lock could be causing your problem. Did you try to move your steering wheel around a little bit to see if it will allow the key to turn? Is your key worn. I have seen worn keys that will cause your problem. Also the tumblers in your ignition could me messed up. You could try putting some dry graphite lube on your key and slide it in and out of your ignition several times to get lubrication into the tumblers and see if that helps.

Apr 22, 2011 | 2004 Chevrolet Monte Carlo

1 Answer

How do I change the ignition switch in my 93 plymouth van?


FIRST OF ALL, TURN OFF RADIO,DISCONNECT NEGATIVE BATTERY CABLE. IF EQUIPPED WITH TILT STEERING COLUMN,REMOVE TILT LEVER.CAREFULLY REMOVE THE UPPER AND LOWER STEERING COLUMN COVERS. REMOVE THE 3 TAMPER PROOF TORX IGNITION SWITCH MOUNTING SCREWS USING SNAP ON TOOL TTXR15A2 OR EQUIVALENT. GENTLY PULL THE SWITCH AWAY FROM THE COLUMN AND REMOVE THE 2 ELECTRICAL CONNECTORS FROM THE IGNITION SWITCH. WITH THE KEY IN THE LOCK POSITION, DEPRESS THE KEY CYLINDER RETAINING PIN FLUSH WITH THE KEY CYLINDER SURFACE. ROTATE THE KEY CLOCKWISE TO THE OFF POSITION THE KEY CYLINDER SHOULD NOW BE UNSEATED. ROTATE THE KEY CYLINDER COUNTER CLOCKWISE BACK TO THE LOCK POSITION, AND REMOVE THE LOCK CYLINDER. ( TO INSTALL ) CONNECT THE ELECTRICAL CONNECTORS TO THE IGNITION SWITCH. BE SURE THE CONNECTORS ARE SECURELY LOCKED IN PLACE. MOUNT THE IGNITION SWITCH TO THE COLUMN 3 SCREWS FOR VECHICLES WITH THE TILT STEERING COLUMN THE SHIFTER MUST BE IN THE PARK POSITION AND THE PARK LOCK DOWEL PIN AND THE COLUMN LOCK FLAG MUST BE INDEXED BEFORE THE SWITCH IS INSTALLED. PLACE SHIFTER IN THE PARK POSITION. PLACE THE IGNITION SWITCH IN THE LOCK POSITION. THE SWITCH IS IN THE LOCK POSITION WHEN THE STEERING COLUMN LOCK FLAG IS PARALLEL TO THE IGNITION SWITCH TERMINALS. POSITION THE PARK LOCK DOWEL PIN OF THE IGNITION SWITCH SO IT ENGAGES THE STEERING COLUMN PARK LOCK SLIDER LINKAGE. APPLY A LIGHT COATING OF GREASE TO THE PARK LOCK DOWEL PIN AND THE COLUMN LOCK FLAG. POSITION THE IGNITION SWITCH AGAINST THE LOCK HOUSING OPENING ON THE STEERING COLUMN. BE SURE THE SWITCH PARK LOCK DOWEL PIN ENTERS THE SLOT IN THE PARK LOCK SLIDER LINKAGE INSTALL THE RETAINING SCREW AND BRACKET. TORQUE THE SCREW TO 26 INCH LBS. INSTALL THE STEERING COLUMN COVERS AND THE TILT LEVER IF REMOVED. WITH THE KEY CYLINDER AND THE IGNITION IN THE LOCK POSITION INSTALL THE KEY CYLINDER INTO THE SWITCH UNTIL IT BOTTOMS. RECONNECT THE NEGATIVE BATTERY CABLE AND THE CHECK THE IGNITION SWITCH FOR PROPER OPERATION OF HALO LIGHT SHIFT LOCK IF EQUIPPED AND COLUMN LOCK.ALSO CHECK FOR PROPER OPERATION OF THE IGNITION SWITCH ACCESSORY, LOCK OFF, RUN AND START FUNCTIONS.

Sep 18, 2010 | 1993 Plymouth Voyager

3 Answers

Ignition locked, key won't turn, 2006 hyundai


If the car is parked on a flat surface, and a potential liquid spill has occured in the gear selector, make sure the car is engaged securely in park.

May 25, 2009 | 2006 Hyundai Sonata

Not finding what you are looking for?
Cars & Trucks Logo

364 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

78936 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...