Question about 1993 Mitsubishi Eclipse

1 Answer

How to remove crankshaft bolt on 93 eclipse - 1993 Mitsubishi Eclipse

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,317 Answers

Either using a heavy duty air impact gun. Or a chain strap wrench to hold the pulley and a long breaker bar.

Posted on May 03, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I remove the crankshaft pulley


which engine?
the fsm covers that, its free to read.
old post.
ZJ jeep 93


4.0L fsm verbatim, buy a puller, or make one, or use a huge gear puller, at edges of pulley, or use a slam hammer, rad out and grill out. or?
24535178-ojy4jbcchjvgbf2ww1qvc1nl-5-0.jpg

May 29, 2014 | 1993 Jeep Grand Cherokee

1 Answer

How i do the timing on my 87 subaru gl awd


It's a bit of a pain but here is what you set it to:


c17hydro_187.gif

Aligning the marks on the flywheel with the marks on the flywheel cover



c17hydro_188.gif

Driver side timing belt (No. 2) and No. 2 tensioner-1.8L engine




c17hydro_189.gif

Passenger side timing belt (No. 1) and No. 1 tensioner


  1. Disconnect the negative battery cable.
  2. Loosen the water pump pulley mounting bolts.
  3. Loosen the alternator mounting bolts and remove the alternator belt.
  4. Remove the water pump pulley bolts and remove the water pump pulley.
  5. Disconnect the electrical harness from the oil pressure switch.
  6. Remove the dipstick tube.
  7. Remove the crankshaft pulley.
  8. Remove the timing belt cover plate, if equipped.
  9. Remove the timing belt cover bolts on the left, right, and center covers.
  10. Remove the timing belt covers.
  11. Remove the rubber cover seal. Clean all mating surfaces.

To install:

  1. Install a new timing belt cover seal.
  2. Install the timing belt covers on the engine using the mounting bolts. Tighten the bolts to 48 inch lbs. (5 Nm).
  3. Install the timing belt cover plate, if removed.
  4. Install the crankshaft pulley, and tighten the bolt to 69-76 ft. lbs. (93-103 Nm)
  5. Install the dipstick tube.
  6. Connect the electrical harness to the oil pressure switch.
  7. Install the water pump pulley and loosely install the mounting bolts.
  8. Install the drive belt and adjust the tension as necessary. Tighten the alternator mounting bolts.
  9. Tighten the water pump pulley mounting bolts.
  10. Connect the negative battery cable.
// // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 77; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]>

Jun 20, 2011 | 1987 Subaru Gl 4WD

1 Answer

Can you tell me where I can print instructions for free to help me change my timing belt in a 93 ford festiva


Here are the instructions for removing the timing cover, and for replacing the timing belt. If this is helpful, please click my accept button! Thanks!
Remove accessory drive belts.
  1. Remove water pump pulley to pump hub attaching bolts, then the pulley.
  2. Remove right inner fender panel to gain access to crankshaft pulley.
  3. Remove outer crankshaft pulley attaching bolts, then the outer stiffener/spacer and outer pulley
  4. Remove inner stiffener/spacer, attaching screws, inner pulley and baffle plate.
  5. Remove attaching bolts, then the upper and lower timing covers.
  6. Reverse procedure to install. When installing crankshaft pulley, ensure curved lip on baffle plate and deep recess of inner pulley face outward

8fb9fc4.gif
  1. Remove timing belt covers as outlined previously.
  2. Remove timing belt tensioner pulley attaching bolt, then the tensioner pulley, spring and spring cover
  3. If reusing old belt, mark direction of rotation on belt to aid installation.
  4. Remove timing belt from crankshaft and camshaft sprockets.
  5. Check crankshaft and camshaft sprockets, tensioner pulley and timing belt for wear or damage. Replace components as necessary.
  6. Align camshaft and crankshaft sprocket timing marks with marks on cylinder head and oil pump housing
  7. Install timing belt. If reusing old belt, ensure belt is installed so that direction of rotation mark made during removal is positioned correctly.
  8. Install spring and spring cover onto tensioner pulley, then install pulley and attaching bolt. Do not tighten bolt at this time.
  9. Install tensioner spring onto anchor, then tighten pulley attaching bolt to torque listed at the end of this section.
  10. Reinstall timing belt covers.

spacer.gif 2006-05-25_081817_fest2.thumb.gif
This photo shows timing marks.


59f76eb.gif

Jul 14, 2010 | 1993 Ford Festiva

1 Answer

Timing belt markings mazda B2500 1998


Timing Belt, Sprockets & Front Cover Removal & Installation Timing belt To Remove:
  1. Disconnect the negative battery cable.
  2. Remove the exhaust side spark plugs, outer timing belt cover, and crankshaft pulley.
  3. Turn the crankshaft until the number one piston is at top dead center (TDC). CAUTION
    The camshaft belt tensioner tool (303-097) can be damaged when trying to relieve belt tension if you attempt to remove the belt without first loosening both the timing belt tensioner adjusting bolt and the spring pivot bolt.
  4. Loosen the timing belt spring pivot bolt, but do not remove it at this point in the procedure.
  5. Loosen the adjusting bolt slowly and release the spring tension.
  6. Turn the tensioner with the camshaft belt tensioner tool (303-097), against the spring pressure, clockwise to the farthest position.
  7. While holding it in this position, tighten the adjusting bolt to hold the tensioner away from the belt.
  8. Remove the timing belt.
To Install:
  1. Be certain that on piston number one, the crankshaft is at TDC with the crankshaft keyway pointing straight up and the circle on the crankshaft sprocket lined up with the notch on the engine front cover.
  2. Line up the timing marks.
  3. Install the timing belt over the crankshaft sprocket going counterclockwise over the oil pump sprocket and over the camshaft sprocket.
  4. Loosen the bolt allowing the tensioner pulley to press against the timing belt. NOTE: The timing belt tensioner should not be tightened or the belt tension will not be evenly distributed over the whole belt.
  5. Turn the crankshaft two revolutions clockwise. Next, slowly bring the crank to the number one position firing position with the keyway on the crank facing up. The dot on the crankshaft gear is lined up with the notch on the front cover.
  6. Check the timing mark alignment again. If necessary, repeat the procedure.
  7. Tighten the bolts. Torque the pivot bolt to 30-40 ft-lb (40-55 Nm). Torque the adjustment/locking bolt to 26-33 ft-lb (35-45 Nm).
  8. Install the crankshaft pulley and tighten the bolt. Torque to 93-121 ft-lb (125-165 Nm).
  9. Install the outer timing belt cover and tighten the bolt. Torque to 70-106 in-lb (8-12 Nm).
  10. Install the exhaust side spark plugs.
Sprockets To Remove:
  1. Remove the timing belt.
  2. Install the camshaft sprocket holding/removing tool (303-098) onto the sprocket.
  3. Remove the camshaft sprocket.
To Install:
  1. Place the key and camshaft sprocket on the shaft.
  2. Install the camshaft sprocket holding/removing tool (303-098) onto the camshaft sprocket and tighten the bolt. Torque to 52-70 ft-lb (70-95 Nm).
  3. Remove the tool then install the timing belt.
Outer Cover To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Remove the fan shroud.
  4. Loosen the bolts on the water pump pulley, but do not remove them at this point in the procedure.
  5. Remove the drive belt, the water pump pulley, and the fan and clutch assembly.
  6. Recover the refrigerant from the A/C system.
  7. Disconnect the A/C wiring connector.
  8. Remove the A/C compressor from the mounting bracket then remove the A/C mounting bracket with the power steering pump still attached.
  9. Remove the outer timing belt cover.
To Install:
  1. Install the outer timing belt cover. Torque to 70-106 in-lb (8-12 Nm).
  2. Install the A/C mounting bracket with the power steering pump still attached. Torque the M10 bolts and stud to 35 ft-lb (48 Nm) and torque the M8 bolt to 18 ft-lb (25 Nm).
  3. Install the A/C compressor to the mounting bracket. Torque to 16-20 ft-lb (21-28 Nm).
  4. Connect the A/C wiring connector.
  5. Refill the refrigerant into the A/C system.
  6. Install the fan and clutch assembly, the water pump pulley, and the drive belt.
  7. Tighten the bolts on the water pump pulley. Torque to 13-17 ft-lb (17-23 Nm).
  8. Install the fan shroud. Torque to 54-70 in-lb (6-8 Nm).
  9. Connect the negative battery cable.
  10. Start the engine. Check for leaks and repair as necessary.
Inner Cover To Remove:
  1. Loosen oil pump sprocket bolt.
  2. Remove timing belt, timing belt tensioner, oil pump sprocket, and crankshaft pulley.
  3. Remove inner timing belt cover.
To Install:
  1. Install inner timing belt cover.
  2. Install crankshaft pulley. Torque to 93-121 ft-lb (125-165 Nm).
  3. Install the oil pump sprocket.
  4. Install the timing belt tensioner. Torque the pivot bolt to 30-40 ft-lb (40-55 Nm). Torque the adjustment/locking bolt to 26-33 ft-lb (35-45 Nm).
  5. Install the timing belt.
  6. Tighten the oil pump sprocket bolt. Torque to 30-40 ft-lb (40-55 Nm).
  7. Torque the camshaft bolt to 52-70 ft-lb (70-95 Nm).

Jul 12, 2010 | 1998 Mazda Pickup

1 Answer

Timeing belt replacement do i need special tools to repalce the timeing belt on a 2002 mitsubishi eculpse v6


actually if you have never done this before, yes...
there is atool to hold the crankshaft pulley in place to remove and re-torque the crankshaft bolt, you'll need a vise to compress the tensioner, they recomend a tool to remove the slack in the belt after installing the new belt, and you'll need an inch pound torque wrench and a foot pound torque wrench that is able to go to 184 NM. air tools help ALOT!

Jul 09, 2010 | 2002 Mitsubishi Eclipse

2 Answers

I am having problem with crankshaft pulley in a


The harmonic balancer/pulley assembly on this car is known to come apart.You likely need a new assembly,the pulley should never come off the balancer.

Apr 09, 2010 | 1993 Mitsubishi Eclipse

1 Answer

Change a crankshaft position sensor on a 2000 eclipse


Is this a V6 or 4cyl???>>>(V6) This requires removing the Harmonic balancer (crankshaft pulley). Remove (R) front wheel, remove engine splash Guard, Remove crank pulley, remove lower timing belt cover. The Crank sensor is located behind the crank shaft pulley!! I highly recommend having this done by a certified tech, requires special tools. Hopefully this helps!!

Mar 11, 2010 | 2000 Mitsubishi Eclipse

1 Answer

Anyone know the thread direction on the crankshaft bolt on a 96 eclipse


You didn't specify what bolt on the crankshaft, but they all should be clockwise threads (tighten clockwise, loosen counter-clockwise). If you are not sure, just imagine you are opening a jar, then orient the lid of the jar in the direction of the end of the shaft

Feb 14, 2010 | 1996 Mitsubishi Eclipse

2 Answers

Honda accord ex 92


Crankshaft pulley (harmonic balancer) removal- disconnect neg battery cable, remove belts, it would be a good idea to soak the bolt w/ penetrating oil overnight, there is a special 'crankshaft pulley holding tool' available to secure the pulley while removing and installing the bolt. Some parts stores loan tools for free if u purchase parts from them, I don't know if this is available, but it would be worth checking out. Attach holding tool and remove bolt securing pulley. Carefully remove pulley from crankshaft, Do NOT pry off. Remove key from crankshaft sprocket,
Install: install key on crankshaft sprocket, slide pulley on, apply clean oil to bolt threads but NOT to washer contact surfaces, secure crankshaft w/ holding tool, tighten to 159 ft lbs (91-93 Accord), install belts, re-attach neg cable.

Nov 11, 2008 | 1992 Honda Accord

Not finding what you are looking for?
1993 Mitsubishi Eclipse Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...