Question about 2002 Saab 9-5

Open Question

2000 saab 95 2.3 turbo looking for torque for cyl head

Posted by on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
BCAS1298
  • 3092 Answers

SOURCE: I AM DOING THE HEAD GASKET ON 1999 SAAB 95 4 CYL I

Torque spec

Step 1- 44 Ft.Lbs.
Step 2- 59 Ft.Lbs.
Step 3- Tighten bolts an additional 90 degrees.

Here the head bolt's tightening sequence.

bcas1298_1.gif

Posted on Nov 11, 2010

Ad
  • 14036 Answers

SOURCE: Saab 95 Aero 2.3 turbo. I need torque settings

CYLINDER HEAD BOATS TORQUE FIRST PASS 29.5 FT LBS SECOND PASS 44 FT LBS.THEN TIGHTEN ADDITIONAL 90 DEGREES FOR MAIN BEARINGS 15 FT LBS TIGHTEN EACH BOAT ADDITIONAL 70 DEGREES ROD BEARINGS 15 FT LB TIGHTEN ADDITIONAL 70 DEGREES. CRANKSHAFT DAMPER BOLTS 130 FT LBS.

Posted on Jan 26, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need torque settings for mazda xa 3.0l diesel 4 cyl


con rod bolt tension is 55-60ft/lbs
crank shaft main bearings is 80-85 ft/lbs
fly wheel bolts95-100 ft/lbs
crank shaft pulley nut 94-123 ft/lb
head studs tension 80-95 ft/lbs working in a spiral direction from no 1 stud directly in the centre of the head. Pull down in 10ft/lb increment starting at 20 ft/lbs
valve clearance is .010" both valves cold but after warming engine and re-tensioning the head studs re set valves to .012 both valves
injector retaining nuts tension12-17 ft/lbs

Dec 25, 2013 | Saab 9 Cars & Trucks

1 Answer

Saab 95 Aero 2.3 turbo. I need torque settings for big end bearings and cylinder head bolts.


CYLINDER HEAD BOATS TORQUE FIRST PASS 29.5 FT LBS SECOND PASS 44 FT LBS.THEN TIGHTEN ADDITIONAL 90 DEGREES FOR MAIN BEARINGS 15 FT LBS TIGHTEN EACH BOAT ADDITIONAL 70 DEGREES ROD BEARINGS 15 FT LB TIGHTEN ADDITIONAL 70 DEGREES. CRANKSHAFT DAMPER BOLTS 130 FT LBS.

Jan 26, 2011 | 1999 Saab 9-5

1 Answer

I AM DOING THE HEAD GASKET ON 1999 SAAB 95 4 CYL I NEED THE TORQUE SPEC ON CYL. HEAD


Torque spec

Step 1- 44 Ft.Lbs.
Step 2- 59 Ft.Lbs.
Step 3- Tighten bolts an additional 90 degrees.

Here the head bolt's tightening sequence.

bcas1298_1.gif

Nov 11, 2010 | Saab 9 5 Cars & Trucks

1 Answer

I need the torque for the head bolt


SAAB 2.3 140 B235 98-03 Head Bolt Torque
Done in 3 sterps
Step I:30 FT/LBS
Step II:44 FT/LBS
Step III a full 90

Jul 21, 2010 | 1999 Saab 9-5

1 Answer

Trouble selecting gears when engine running at standstill but clutch not slipping saab 95 2 ltr turbo 2004


try bleeding the slave cyl if hydraulic, if not it may be an adjustment could be the clutch is reaching its wear limit, or the pilot bearing is not rolling free either way you will have to remove the trans,

Jul 19, 2010 | Saab 9 5 Cars & Trucks

1 Answer

Where is the turbo located on my 2000 saab 9-5


If 4 cyl, turbo in the front passenger bottom of the engine. Why do you need to know?

Jul 13, 2010 | 1999 Saab 9-5

4 Answers

What oil should I use in my Saab 96 900?


factory recommends you use 10w-30 motor oil ,hope this is helpful.

Nov 27, 2009 | 1996 Saab 900

2 Answers

1997 saab 4 cyl non turo give check gearbox light


Take it back to the Dealer........Their Problem not yours.
It is possible that a plug was removed during the service and at some stage the ignition was switched on before the plug was reconnected , this would cause a check light and the computer would store this until the light was reset.
Hope this helps.

Jun 26, 2009 | 1999 Saab 9-5

Not finding what you are looking for?
2002 Saab 9-5 Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saab Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76630 Answers

rgbypoet

Level 2 Expert

166 Answers

Are you a Saab Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...