Question about 1996 Toyota Camry

1 Answer

Broken wiring harness: driver side door, 1996 Toyota camry le. Need to order new part. Can't find an on-line store. Can you help

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 26 Answers

ROCKAUTO ,madison ,wisconsin

Posted on May 03, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Drivers window and back passengers windows do not roll down purchased used master switch and the problem is still there. I can roll the window up by using a battery and wires. I am stumped can you help?

you need to check the wires that come in from the left drivers side kick panel to the drivers front door......when you open the drivers side front door you will see the harness that comes from inside the car to the door and 99% of the time you will find that there will be broken wires......this is a common problem on these cars.....the best way to check this is to unplug the harness behind the kick panel and take the door panel off and feed the harness back through the door and pull back the black rubber cover that is protecting the wires.......once you have all of the wires exposed start checking for any broken wires and also you might want to take each wire one at a time and pull on them to see if any of the other wires are about to break cause the insulation around the wire could be the only thing holding it together......the wire inside will break over time and the insulation will not....hope that this will help you and if you need more info let me know.....let me and fixya know if i was any help to you and a comment and a thumbs up would let me know how i am doing.....thanks and have a blessed day........good luck and i do believe you will find your problem in the door harness and dont forget to check all of the wires......

Jul 22, 2011 | 1996 Toyota Camry

1 Answer put new regulator on main drivers window. still dont work..96 camry

does it have power and ground to motor when you work the switch and if it dont then there is probably some broken wires in the wiring harness that goes from the left kick panel to the door. they always break in the section between the door and body and one way to check this is to pull the harness out of the door and cut the rubber back and start pulling on each wire to see which one is broken and they could already be visibly broken.the switch or the motor itself could also be bad if you did not replace the motor and the only other way to check all of this is with a electrical wiring diagram and a volt meter.i have repaired tons of these with the wires broken. let me know if i can help any further and to give me more info. good luck...............

Jun 17, 2011 | 1996 Toyota Camry

1 Answer

Power windows and door locks do not work, At first they intermittently stopped working and now they don't work at all. The fuses appear to be okay. Could the circuit breaker be faulty? How do I change...

this generation Camry has a known issue with the harness that goes through the driver side door (from under the dash to the door) getting damaged over years of door opening/closing-I went thought this recently and found many broken wires in that harness, you need to remove the door panel and check the wiring in the sheath for breaks-some are hard to find as the insulation may still be intact, I did price that harness at a local toyota dealership and it is $115, so I ended up using a digital meter set to continuity to find the breaks, and I spliced and sodered the damaged wires. ime consuming, but it worked.

Jun 07, 2011 | 1989 Toyota Camry

1 Answer

I have a '92 Toyota Camry LE 4cyl., my passenger side pwr. window motor will go up but not down with the switch. When I use a jumper from the battery it will work great but not with the switch on the...

Have you tried replacing the master switch in the drivers door?
Toyota switches can be dismantled ( carefully ) and the usual problem is dirty contacts.
When you dismantle the switches use a small flat blade screwdriver and do the job in a large clean area where you can find small springs and ballbearings that will fire everywhere if let them.
Happy hunting, Marshall

Apr 29, 2010 | 1992 Toyota Camry V6

1 Answer

1996 toyota camry power windows won't go down. checked the 30 amp pink switch under the dash and it's good. pulled the main switch from the drivers door and no obvious issues with the circuit board. the...

the wire harness that runs from the door to the car from opening and closing the door ive seen the wires break try to move them first while working the switch sometimes it will start to work

Feb 28, 2010 | 1991 Toyota Camry

1 Answer

1998 Toyota Camry tail lights and backup lights won't work


I have a solution for you, as I see your same issue in my shop quite a bit...There are two possibilities:

You may have a broken wire. This is a very common issue.

Open up the trunk lid, and look at the hinge on the driver side. You will see a wiring harness, in a plastic tube, attached to the arm that holds th trunk lid to the car.... Remove the tubing, and follow the wires towards the back seat area. You are probably going to find a wire that has been broken, from the many actions of opening and closing the trunklid. Splice and resolder the wire, and you should be fine.

The other issue is the tallamp failure sensor may have burned out. This too is rather common. Open the trunk lid, and pull back the inner carpeting on the driver side of the trunk. Locate a small box (it will be white or blue), on a brace. The box is closer to the quater panel sheetmetal. Remove the box, and take it apart. If it looks or smells burnt, you need a new sensor.

Nov 30, 2009 | 1998 Toyota Camry

1 Answer

Need wiring schematics for 96 toyota camry

hayne's (or chilton's) manual from an auto parts store. $17.

Mar 04, 2009 | 1996 Toyota Camry

3 Answers

1996 toyota camry

It is not a fuse. All of the windows are on thje same circuit. You either have a bad window motor, or a bad driver side door master window cantrol switch.

Feb 07, 2009 | 1996 Toyota Camry

1 Answer

Failed power window

I'd bet on a broken wire in the harness going to the drivers door. I suggest the drivers door because it is used the most often. You can pull the master switch and check the wires for continuity to the harness just under the dash at the fuse box, after removing the lower dash trim panel. Sometimes you can gently pull on the wires of the door harness from under the dash and one will pull right out. Thats how I found mine.

Jul 08, 2008 | 1992 Toyota Camry V6

Not finding what you are looking for?
1996 Toyota Camry Logo

Related Topics:

339 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

80637 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides