Question about 1997 Infiniti.5 Q45

1 Answer

How do i change the xenon head light bulbs on my 01 q45

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 26 Answers

Take to dealer,or if you do it ,please unplug/disconnect the battery,I know on BMW's there are stickers on the front bar under the hood showing a guy getting shocked with 25,000 volts, ,and people have been fryed doing so. thats why there are stickers to worn us . so ,take it to the dealer,if they mess it up they have to fix it.

Posted on May 03, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

If i was to change headlight globes from 55 watt low/65 watt high to xenon halogen 90 watt low/100 watt high is there any problems


Most OE factory wiring is marginal as far as amperage carrying capability goes. They installed wiring fine for the stock bulbs and switch. A lot of vehicles send power to the lights..head and running...through the light switch on the dash. This causes it's own problems as switches are the weak link in the lighting system.

If you run 100watt bulbs you will need to power the bulbs via a 40 amp relay switched by the light switch so the switch does not carry the amperage load through it's contacts.

Doing so will reduce the voltage drop to the bulbs as a 2 volt drop will cause the bulbs to be only 75% as bright as they would be with the full 13.5 volt running voltage..

You run a fused wire from the battery or power distribution block to the relay that should be mounted within 6 inches of the closest h/l bulb. Then from the relay to the head light bulb/s. The front and rear running lamps can remain as factory as they are low amperage draw and original light switch will work because you now no longer run power to the h/lamps through the switch.

Search the www for schematics for relay switched lamps.


.

Mar 12, 2014 | Cars & Trucks

2 Answers

How to change headlight bulb


On the back of the headlight where the wires enter, you should be able to twist and remove the lamp holder. Be careful with the new bulb if it is halogen, do not touch the bulb!!

Apr 13, 2013 | 2000 Hyundai Sonata

2 Answers

How do I get to the front headlight to change it


Re: Replace headlight bulb

  1. INSTALLATION GUIDE:
  2. BMW E38 99-01 HID TYPE 7 Series 1PC Halo Amber Projector Headlights
  3. Parts Identification:
  4. Projector Headlight
  5. Halo & L.E.D.
  6. Bottom of the Headlight:
  7. Ballast Bracket, Halo Wires(red/black)
  8. Turn Signal Adaptor
  9. TOOLS REQUIRE
  10. 10mm - 8mm socket
  11. Philip Screwdriver
  12. Crimper/Pliers
  13. For more information about how to install your vehicle, come visit our youtube page on
  14. http://www.youtube.com/spyderauto
  15. Remove the facotry headlight from the BMW. First remove the front panel cover below the headlight to access the bottom screw of the headlight housing. There is also two screws on the top of the housing.
  16. Once you have remove the headlight, turn the headlight around and remove the bracket that holds the Ballast. Then remove the ballast using a philip screwdriver.
  17. Unplug the wire from the ballast, and then remove the Xenon Plug from the housing. Put the Ballast aside.
  18. Carefully remove the D2S Xenon Bulb from the factory housing. Once you have remove the bulb, transfer the bulb to the Spyder headlights.
  19. Remove the bracket from the Spyder Headlight, and then install the ballast on the housing like the original. Once you have put the ballast on, put the bracket back on.
  20. Remove the Panel Cover bracket from the original headlight to the new Spyder Headlights as shown here.
  21. STEP:
  22. Install the Spyder turn signal socket if the orignal does not fit, unplug the factory plug from the harness and plug the new one on.
  23. Install the Spyder Headlight back on to the vehicle. Plug the Harness back on, the halo/L.E.D. Wires is connect to the Parking lights. These wires are optional to your vehicle, you do not have to wire them together.
  24. Factory Xenon Headlight
  25. Spyder Projector Headlight using Factory Xenon Lights
  26. STEP:
BMW e46 HID Headlight Replace
get-front-headlight-change-afy5cnsznmokzumyhdcbeseq-5-0.jpg

get-front-headlight-change-afy5cnsznmokzumyhdcbeseq-5-2.jpg

Nov 22, 2012 | Cars & Trucks

1 Answer

How to change headlight bulb on 2009 smartcar fortwo


first you should what is your car bulb type, such as HID Xenon Light H4 bulb. And open you hood, there is a rubber grommet the size of a coaster thats where the bulb is located. unplug the plug (squeeze the side of the plug and it should slide right off)
remove the grommet. just pull if off away from the headlight.
the bulb is secured by a spring clip push the clip towards the front of the car and move it to one side to get it unhooked from the headlight housing.
pull the head light bulb out. replace with new head light bulb (MAKE SURE NOT TO TOUCH THE GLASS OF THE NEW BULB)
secure the bulb with the spring clip.
put rubber grommet back on
plug the harness back on the bulb.
your done

Oct 30, 2012 | Smart Cars & Trucks

1 Answer

How do i change a headlight bulb on a 2007 520d estate?


first is the headlight Xenon or normal? Xenon : The bulb is situated behind the backing cover on the light and is a clip on cover! remove this cover and the xenon bulb and module will be exposed. turn this unit anti-clock wise direction and it should come out easily. unplug the small wire and replace the bulb and or the small unit that has been removed. DON'T TOUCH THE BULB ! as this will damage it!
Normal: Remove the round cover and the bulb will be exposed !, remove wire connector and un clip the retainer spring, replace bulb!

Feb 08, 2011 | 2007 BMW 530xi Sports Wagon

1 Answer

Repairing the light on the analog clock of a 2002 infinity Q45


repairing the light on the analog clock of a 2002 infinity Q45
i want ti know which model should i buy (bulbs burned)

Jan 15, 2011 | 2004 Infiniti Q45

1 Answer

How to remove headlight covers on 2002 q45


These are sealed units so if a new light bulb is needed change it from the back side of the headlamp assembly

Jun 08, 2010 | 2004 Infiniti Q45

2 Answers

How do you change front headlight blub 2008 sonata


how do you change front headlight blub 2008 sonata

Nov 28, 2009 | 2008 Hyundai Sonata

1 Answer

How to change the bulb on the front head light on my 2002 jaguar x-type


Dip beam (outer) headlight
Open the bonnet.
Slide open the two spring clips (A) and remove the cover (B).
Press the spring clip inwards and push towards the bulb
to release the bulb and then remove the bulb from the light
unit. Pull the connector from the bulb.
Fit a new bulb to the connector, type H1 for dipped beam.
Fit the bulb to the light unit, the bulb will only correctly fit in
one position. Engage the spring clips to retain the bulb and then
fit the cover and retain using the two spring clips.
Close the bonnet.
Note: High Intensity Discharge (HID) Xenon light units,
type D2S 35W, are not renewable, contact your Dealer if the headligh fails to operate

Oct 07, 2009 | 2002 Jaguar X-Type

1 Answer

How do I change the head xenon light bulb on my 2002 Audi A6


you need to remove the headlamp assembly to change the bulb should be held in with 3-4 10mm bolts

Aug 19, 2009 | 2002 Audi A6

Not finding what you are looking for?
Cars & Trucks Logo

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Infiniti Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14333 Answers

Are you an Infiniti Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...