Question about Ford E-150

1 Answer

On a 1995 ford E150,where is the rear heater blower motor,and how is it removed.

Posted by on

  • lmitchell734 May 03, 2010

    very helpful. thank you

  • lmitchell734 May 03, 2010

    very helpful. thank you

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 8,197 Answers


REMOVAL & INSTALLATION

  1. Remove the third, fourth and fifth bench seats, (if equipped).
  2. Remove the left center bolster, left lower front, and left rear lower and upper trim panels (if equipped).
  3. Disengage the blower motor tube and electrical connector.
  4. Loosen the retaining screws and remove the motor.

To install:
  1. Install the motor and tighten the retaining screws.
  2. Engage the electrical connections and tube to the motor.
  3. Install the trim panels.
  4. Install the seats.

Posted on May 02, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the Blower motor relay on a 2002 Ford Econoline E150, and how do you change it so both the front and rear blower motors work on all 3 speeds?


There would be two relay's , one for front an one for the back . And the relay would be for high speed only . And it just so happens there are two AUX blower motor relay's .
Auxiliary Blower Motor Relay C403
Left rear corner of vehicle, above wheelwell
Auxiliary High Blower Motor Relay C404
Left rear corner of vehicle, above wheelwell

Front blower motor relay - K73 top left , Six relay's at top left .


check it out here http://www.bbbind.com/free_tsb.html

Feb 17, 2017 | Ford Econoline Cars & Trucks

1 Answer

Heater doesn't work in 1995 ford econoline van.


I looked at e150, 5.0L engine.
Does the blower motor work? If so, does the engine reach normal operating temp? If so, are the heater hoses, hot? Circulation through heater core? Next, maybe a temp door under the dash has a problem?

Nov 30, 2016 | 1995 Ford Econoline

1 Answer

Wheres heater fan on 91 e150


Usually bad blower motor resister mounts into the heater box under hood.

Dec 28, 2014 | Cars & Trucks

1 Answer

No heat in my 2002 Ford E150


Did you check the fuse ? 12v direct to blower motor ? Or check the control switch ?

Dec 27, 2013 | Cars & Trucks

1 Answer

I have a 1997 ford econoline van e150. The heater is not blowing hot air. I got a new switch motor but some told me it needs to be timed. I don't know how to do tht Please help


If the fan motor is not running & you replaced switch problem could be blower motor or blower motor speed resistor if you vehicle has one.
Check with auto parts store if your vehicle has a resistor.
I hav enever heard of timing for/of a blower motor or switch.

Nov 30, 2013 | Cars & Trucks

1 Answer

Good Morning, I have a Ford E150 1995 with rear air conditioner. I have seen anti freeze on the ground by the left rear tire. Is that a metal line or rubber hose. Thanks for your any help you can give me.


The plumbing to the rear heater is metal lines under the body and then connect with rubber to the core in the heater, with the age of the van the leak is most likey the metal lines corroded. If you don't need the rear heater operational, the lines can be by-passed in the front of the van [ it will not affect the cooling system].

Mar 14, 2011 | Ford E-150 Cars & Trucks

1 Answer

How to replace main heater fan


Blower Motor REMOVAL & INSTALLATION Front Fig. 1: Front heater blower motor assembly 89696g02.gif
Remove the glove box to access the front blower motor, which is on the firewall 89696p02.jpg
The blower motor is retained by four bolts (arrows) 89696p03.jpg
The blower motor vent tube helps to cool the blower motor for efficient operation 89696p04.jpg
Push up on the clip to remove the blower motor connector 89696p05.jpg
A ratchet with extensions makes removal of the retaining screws easier 89696p06.jpg
Lift the blower motor over the control cable . . . 89696p07.jpg
. . . and remove it from the vehicle 89696p08.jpg
  1. Disconnect the negative battery cable.
  2. Open the glove box door. Gently squeeze the retainers at the rear of the box inward and allow the box to swing downward. NOTE: If additional access is required, unfasten the glove box hinge retainers and remove the assembly.
  3. Label and disconnect the electrical harness from the blower motor.
  4. Remove the blower motor housing tube and/or blower motor cover.
  5. Remove the blower motor retaining screws.
  6. Remove the blower motor from the A/C evaporator. To install:
  7. Install the blower motor in the A/C evaporator and tighten the retaining screws securely.
  8. Install the blower motor housing tube and/or blower motor cover.
  9. Connect the electrical harness to the blower motor.
  10. Reinstall the glove box and close its door.
  11. Connect the negative battery cable.
Rear Fig. 2: Service cover push pin locations 89696g03.gif
  1. Disconnect the negative battery cable.
  2. Remove both rear passenger seats.
  3. Remove the three push pin retainers from the lower edge of the auxiliary heater and air conditioning service cover.
  4. Lift the service cover outward and upward to remove.
  5. Label and disconnect the electrical harness.
  6. Remove the blower motor housing tube.
  7. Loosen the three retaining screws and remove the blower motor. To install:
  8. Install the blower motor and tighten retaining screws securely.
  9. Install the blower motor housing tube.
  10. Connect the electrical harness.
  11. Position the service cover and install the three push pin retainers from the lower edge of the cover.
  12. Install both rear passenger seats.
  13. Connect the negative battery cable.
prev.gif next.gif

Dec 19, 2010 | 1998 Ford Windstar

1 Answer

How to remove the blower motor from a 1978 ford bronco full size truck?


Deluxe Hi-Lo Heater
  1. Disconnect the battery cable, remove the carburetor air cleaner and partially drain the coolant system.
  2. Remove the heater hoses from the heater core.
  3. Remove the glove box liner and remove the register duct by pulling from the instrument panel register and releasing the clip at the plenum.
  4. Disconnect the right cowl outside air inlet vacuum hose from the outside/recirculating door vacuum motor.
  5. Remove the rear housing from under the instrument panel. Remove the outside air inlet duct from the rear housing (4 nuts and 1 bolt) and install one upper nut to retain heater housing-to-dash after rear housing is removed.
  6. Remove two screws retaining plenum-to-dash (above transmission tunnel) and two screws to heater housing and remove the plenum.
  7. Install a piece of protective tape on A-pillar inner cowl panel, at lower right corner of instrument panel.
  8. Remove the lower right instrument panel-to-A-pillar bolt to hold the panel in the rearward position.
  9. Remove the heater core (3 screws retaining 2 plates).
  10. Remove the temperature blend door (snaps off).
  11. Remove the temperature blend door arm support (2 screws) and pivot arm retainer (1 screw).
  12. Remove blower motor (2 screws) and remove blower wheel.

To install:
  1. Transfer blower to blower motor and panel assembly.
  2. Install door arm pivot retainer (1 screw) and door arm support (2 screws).
  3. Install the temperature blend door (snaps on).
  4. Install heater core.
  5. Install the plenum (4 screws).
  6. Connect blower wires.
  7. Remove heater housing upper retaining nut and install the heater outlet (4 nuts and 1 bolt). Position the air inlet duct.
  8. Connect the white vacuum hose to the outside/recirculating door vacuum motor.
  9. Reposition the instrument panel, install the retaining bolts and remove the protective tape at the A-pillar inner cowl panel, lower right corner of instrument panel.
  10. Install the right register duct assembly and install the glove box liner.
  11. Connect heater hoses to the heater core assembly.
  12. Fill cooling system, install the air cleaner and connect the battery cable to the battery.
  13. Check blower motor operation.

Jan 19, 2010 | 1981 Ford Bronco

1 Answer

I have a 2000 ford E350 van with front and rear air. the front blower motor runs at low speed, The front blower still runs on low even when the knob is set on medium or high. I do not know where the...


it's either the blower motor switch or blower motor resister. Resistor ?Heater Blower Motor Switch Removal Remove the battery (10655) ; refer to Section 414-01 . Remove the battery tray. Remove the screws. Remove the battery tray. Disconnect the heater blower motor switch resistor connector. Remove the heater blower motor switch resistor (18591). Remove the two screws. Remove the heater blower motor switch resistor. ----------------------------------- Switches Removal Disconnect the battery ground cable. Remove the center trim panel; refer to Section 501-12 . Remove the control assembly. Remove the screws. Remove the control assembly. Remove the A/C-heater function selector switch knob. Disconnect the vacuum harness connector. Disconnect the A/C-heater function selector switch connector. Remove the A/C-heater function selector switch. Remove the screw. Remove the A/C-heater function selector switch. Remove the temperature control switch knob. Disconnect the temperature control switch connector. Remove the temperature control switch. Remove the screw. Remove the temperature control switch. Remove the heater blower motor switch knob. Disconnect the heater blower motor switch connector. Remove the heater blower motor switch (18578). Remove the screw. Remove the heater blower motor switch. ----------------------------

Mar 31, 2009 | 2007 Ford E-350 Super Duty Length XLT

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...