Question about 1998 Chevrolet Camaro

1 Answer

Changing head gaskets

I am trying to change my heads on my 98 camaro its a v6.. i have all the bolts out but there is like a glue of some sort and the top partr of the engine wont come up so i can get to the heads. please help!

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 834 Answers

If you are referring to the intake manifold, be very certain that you have removed all of the bolts from the upper and the lower intake manifolds. Here are some diagrams that might be useful to you.

If you are certain that all of the bolts are removed from the manifolds, then you can break the seal holding the intake manifold by using a large screwdriver, wedge it between the intake manifold and the cylinder head and you should then be able to pry up the intake manifold and get it to break loose.

You did not specify what engine you had so these diagrams are for a 1998 3.8 litre V-6 engine. I hope that they will be of any use to you.changing head gaskets - 8d58a40.gif97f8120.gifc0dadb4.gif0f0a8e9.gif

Posted on May 02, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change and replace valve cover gaskets in a 2004 Chrysler Sebring Convertible 2.7L DOHC V6


You first have to remove the ignition coils or plug wires and then remove the bolts holding the cover to the cylinder head. Discard old gasket. Clean gasket channel of any oil and install new gasket to cover taking care during assembly not to disturb gasket when placing cover back on cylinder head. The rear gasket is much harder to change as the upper plenum must be removed to access this cover. You should have some knowledge of engines if you are going to atempt this repair on your own

Apr 05, 2015 | Chrysler Cars & Trucks

1 Answer

How do I change the head gaskets on a 98 for expedition xlt 4.6L?


this really isn't the place to get an answer as it will not be a straight forward few lines to give the answer, you will need a manual that shows the head torque sequence and the torque settings for the various bolts and it may also give you the strip down procedure

Mar 02, 2015 | 1998 Ford Expedition

1 Answer

I need to know the torque specs for the head gasket for a 96 3.8 chevy camaro


Tighten the cylinder head bolts to 50 N·m (37 lb ft) in sequence.

Use a torque angle meter to rotate each cylinder head bolt 120 degrees in sequence.

Use a torque angle meter to rotate the four center cylinder head bolts an additional 30 degrees in sequence...

I hope this helps.

Jul 06, 2011 | 1996 Chevrolet Camaro

3 Answers

I need torque settings for the engine ie head bolts v6 engine 1


i am replacing the heads on a GMC 350 cu in engine. what is the final torque of the head bolts?

Jul 15, 2010 | 1985 Chevrolet Camaro

2 Answers

Which is the hole for coolant temp sensor on my 87 camaro 2.8v


located on the left cylinder head. at the front. it is right where the power stering is

Feb 17, 2010 | 1995 Chevrolet Camaro

1 Answer

1993 camaro 3.1 v6 running hot,evidence of a small oil leak thru the head cylinder.


possible blown head gasket....be sure to check that cooling fan comes on after engine is at operating temperature

Oct 10, 2009 | 1996 Chevrolet Camaro

2 Answers

How do I replace my valve cover gaskets on my 1992 toy cam v6 3.0


this is relatively easy unbolt the cover from the head (this usually requires a 10 milimeter socket)once unbolted pull the cover off make sure you clean the old gasket off the cover and the head glue the gasket back to the cover and reverse the process used to take it off be careful not to over tighten the new gasket so as not to split it and cause it to leak.

Oct 03, 2009 | 1992 Toyota Camry V6

1 Answer

Nead help


If it is blowing white smoke, it's definately the head gasket.

Mar 26, 2009 | 1994 Chevrolet Camaro

2 Answers

1999 Chevy Camaro


The best site for camaro help is http://www.ls1tech.com

Sep 25, 2008 | 1999 Chevrolet Camaro

Not finding what you are looking for?
1998 Chevrolet Camaro Logo

465 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...