Question about 1994 Dodge Intrepid

Open Question

1994 Dodge Intrepid headlights adjustment

Hi!
How do i adjust, verticaly, the headlights on a 1994 Dodge Intrepid?

Thanks,
Mag

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 36 Answers

SOURCE: adjusting the headlights on a 99 dodge intrepid

On the back of the headlight their is a bolt which you could turn it one way and it lowers the headlight the other way it picks it up.

Posted on Nov 03, 2008

  • 840 Answers

SOURCE: 1996 dodge caravan headlight up/down adjustment ?

there are 2 hex screws that one is for adjusting ht and the other is for adjust in and out and they are just inside the hdlt. if you need more advice go to collisionrepairadvice.com

Posted on Mar 10, 2009

emissionwiz
  • 75222 Answers

SOURCE: how to adjust timing for 94 dodge intrepid

1st the belt must ALWAYS be replaced when the water pump is done or anytime the belt is distrubed, here are the only instructions I could find on the belt replacement.
http://www.allpar.com/fix/timingbelt35.html

Posted on Jun 18, 2009

  • 1986 Answers

SOURCE: adjusting headlights on 2001 dodge Ram 2500

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Posted on Sep 30, 2009

  • 1986 Answers

SOURCE: How do I adjust headlights on 2004 Intrepid

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Posted on Oct 20, 2009

Testimonial: "Thanks for the very helpful info"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1994 dodge dakato slt 3.9 how to remove headlight cover and side marker benzel


There are screws in plain site to remove the chrome trim

No cables involved ,just headlamp adjustment screws

Mar 04, 2014 | 1994 Dodge Dakota Club Cab

1 Answer

How do I find the headlight adjustment


You need an aiming tool to use those "two little" adjusters.

Dec 15, 2013 | 2003 Dodge Intrepid

1 Answer

Where are adjustment screws on my 2002 dodge intrepid headlight?


On top of the housing of the headlight, you will see some small holes. With the use of a flashlight, look through these holes and you will see some torqux screws (T-20 or T-25 star bit). First loosen the headlight housing. With the use of the stars bits, adjust the headlight as needed and then re-tigthen the housing. You're done.

Oct 06, 2010 | 1999 Dodge Intrepid

1 Answer

Can not find headlight adjustment screws


YOU NEED A HAYNES REPAIR MANUAL.IT HAS 3 HEAD LIGHT ADJUSTMENT SCREWS WITH PHOTOS.IT WOULD BETTER TO TAKE TO A GARAGE.SHOULDNT COST MUCH BUT GET A PRICE CHECK.THEY HAVE EQUIPMENT TO ADJUST HEAD LIGHTS.IF YOU TRY ADJUSTING THEM YOUR SELF.YOUR HEAD LIGHTS WILL BLIND OTHER DRIVERS IF ADJUSTMENT NOT CORRECT.

Mar 06, 2010 | 1999 Dodge Intrepid

1 Answer

How do you replace headlights 94 dodge intrepid


The headlight bulbs are inserted into the headlight housing. To remove the bulb, disconnect the wiring harness, then twist the bulb housing to remove the bulb. Insert a new bulb and install the wiring harness.

Nov 01, 2009 | 1994 Dodge Intrepid

1 Answer

Where can i find the timing points on a 1994 3.5 liter dodge intrepid


You do realize that is all controlled electrically by computer right?
Non adjustable by normal procedures.
Or are you changing timing belt & need reference points ?

Aug 04, 2009 | 1994 Dodge Intrepid

1 Answer

1999 Dodge Intrepid...shift lever wil shift gears


I believe that the cable has to be adjusted. Most cases, the cable adjustment is off. Worst case senario, is the bushing in tranny is worn out.

Jun 22, 2009 | 1994 Dodge Intrepid

1 Answer

How to adjust timing for 94 dodge intrepid


1st the belt must ALWAYS be replaced when the water pump is done or anytime the belt is distrubed, here are the only instructions I could find on the belt replacement.
http://www.allpar.com/fix/timingbelt35.html

Jun 18, 2009 | 1994 Dodge Intrepid

1 Answer

94 dodge intrepid no low-beams


It could be a dimmer switch. Although make sure both Head light bulbs aren't burnt out. Check for power and ground at the low beam headlight connectors.

Feb 26, 2009 | 1994 Dodge Intrepid

1 Answer

Adjusting the headlights on a 99 dodge intrepid


On the back of the headlight their is a bolt which you could turn it one way and it lowers the headlight the other way it picks it up.

Sep 25, 2008 | 1999 Dodge Intrepid

Not finding what you are looking for?
1994 Dodge Intrepid Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...